Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › EXHAUST PIPE › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053680 1GD-FTV INTAKE / EXHAUST _0260653 EXHAUST PIPE A

1GD-FTV INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

NOTICE:
A372594

w/ Urea SCR System:

Do not hold the front exhaust pipe assembly at the location shown in the illustration. Otherwise, it may become deformed or damaged, adversely affecting its thermal insulation capabilities.


a.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Minimum free length:

41.5 mm (1.63 in.)


If the free length is less than the minimum, replace the compression spring.



b.
A076194C46
2.031,1.583 1.594,1.885 1.594,1.885 1.479,1.885 true 2.438,0.979 3.042,0.979 true 1.281,1.781 1.542,1.969 0.26,0.188 10 false *1 3.063,0.875 3.313,1.156 0.25,0.281 10 false *a
*1 Gasket
*a Wooden Block


Using a plastic-faced hammer and wooden block, tap in a new gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Be sure to install the gasket so that it faces the correct direction.

·

Do not reuse the gasket.

·

Do not damage the gasket.

·

When connecting the front exhaust pipe assembly, do not push in the gasket with the front exhaust pipe assembly.




c.

Install a new gasket and the front exhaust pipe assembly and 2 compression springs with the 2 bolts.


d.
A329093C37
1.667,0.573 1.979,0.729 0.313,0.156 10 false *a
*a Torque Wrench Fulcrum Length


w/ Urea SCR System:

Using a 14 mm union nut wrench, tighten the 2 bolts.

Torque:
Specified tightening torque : 43 N*m (438 kgf*cm, 32 ft.*lbf)

HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

·

When using a union nut wrench (fulcrum length of 30 mm (1.18 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 38N*m (385 kgf*cm, 28 ft.*lbf)




e.

w/o Urea SCR System:

Install the front exhaust pipe assembly and 2 compression springs with the 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)


f.

Connect the front exhaust pipe assembly to the exhaust pipe support.


Hide 23203A 2.INSTALL UREA INJECTOR SET (w/ Urea SCR System)

Hide 17420 3.INSTALL CENTER EXHAUST PIPE ASSEMBLY

a.

for 3 Door:

Connect the center exhaust pipe assembly to the 2 exhaust pipe supports.


b.

for 5 Door:

Connect the center exhaust pipe assembly to the 3 exhaust pipe supports.


c.

Install the center exhaust pipe assembly with the 2 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 894A0 4.INSTALL PARTICULATE MATTER SENSOR (w/ Urea SCR System)

Hide 89425C 5.INSTALL NO. 4 EXHAUST GAS TEMPERATURE SENSOR (w/ Urea SCR System)

Hide 89463D 6.INSTALL NO. 2 NITROGEN OXIDES SENSOR (w/ Urea SCR System)

Hide 89439K 7.INSTALL NO. 3 SENSOR BRACKET (w/ Urea SCR System)

Hide 17430 8.INSTALL TAILPIPE ASSEMBLY

a.

Install a new gasket to the tailpipe assembly.


b.

Connect the tailpipe assembly to the exhaust pipe support.


c.

Connect the tailpipe to the center exhaust pipe assembly.


d.

Install the 2 bolts.

Torque:
48 N*m (489 kgf*cm, 35 ft.*lbf)


Hide 9.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.