Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2018.06–2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  Drive Start Control  


DESCRIPTION

The drive start control is controlled by the ECM.

If the ECM determines that the shift lever and accelerator pedal are operated abnormally, engine output is restricted and, when necessary, a warning is displayed on the combination meter assembly.

A373286E39
0.385,0.615 2.573,0.917 2.188,0.302 10 false Accelerator Pedal Position Sensor 2.635,0.896 4.167,1.438 1.531,0.542 10 false Actual Accelerator Pedal Opening Value 0.344,1.438 2.01,1.854 1.667,0.417 10 false Steering Angle Sensor and Air bag ECU Assembly 2.677,2.198 3.969,2.615 1.292,0.417 10 false Vehicle Acceleration and Steering Angle 0.365,3.125 2.167,3.635 1.802,0.51 10 false Park/Neutral Position Switch Assembly 2.688,3.604 3.958,3.865 1.271,0.26 10 false Shift Lever Position 0.396,4.302 2.031,4.875 1.635,0.573 10 false Vehicle Speed Sensor or Wheel Speed Sensor 2.667,4.729 3.708,5.01 1.042,0.281 10 false Vehicle Speed 0.375,5.438 2.49,5.729 2.115,0.292 10 false Transmission Revolution Sensor 2.688,5.677 3.979,5.99 1.292,0.313 10 false Input/Output Speed 4.365,6.354 4.823,6.552 0.458,0.198 10 false ECM 5.667,1.354 7.104,1.958 1.438,0.604 10 false Meter Display Request (Only during shift control) 5.698,4.302 6.604,4.896 0.906,0.594 10 false Engine Output Request


CAUTION / NOTICE / HINT

HINT:

Even if the accelerator pedal position is maintained, the engine output may increase when driving uphill and decrease when driving downhill. This is due to the drive start control controlling the engine output, and is not a malfunction.


PROCEDURE

1.SYMPTOM CONFIRMATION
a.

Interview the customer to confirm the problem.


Result:
Result Proceed to
Hunting A
Hesitation/poor acceleration B



A

2.PAST ACTIVATION CONFIRMATION

B

8.PAST ACTIVATION CONFIRMATION
2.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:
Drive Start Control Activation Conditions
Shift control

Activation conditions


·

Pattern A (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift lever is moved from P to any forward position (D or S) or R.



·

Pattern B (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift lever is moved from R to any forward position (D or S), any forward position (D or S) to R, or N to R.

A396026E38
4.594,3.958 5.354,3.479 true 4.052,3.5 4.948,3.042 true 4.063,3.042 4.344,2.615 true 2.604,1.719 4.906,1.479 true 3.094,0.99 3.781,0.563 true 3.271,4.115 3.885,4.313 0.615,0.198 10 false Time 5.125,3.313 6.5,3.563 1.375,0.25 10 false with control * 4.198,2.438 5.188,2.708 0.99,0.271 10 false without control 4.833,2.875 5.604,3.167 0.771,0.292 10 false Restricted 2.781,2.51 3.365,2.771 0.583,0.26 10 false Activated 1.156,3.271 2.25,3.635 1.094,0.365 10 false Engine Output 0.99,1.198 2.26,1.542 1.271,0.344 10 false Shift Lever Position 0.802,1.958 2.25,2.25 1.448,0.292 10 false Accelerator Pedal OFF 4.948,1.281 6.833,1.938 1.885,0.656 10 false Accelerator pedal is open by approximately 1/5 or more. 3.771,0.417 6.302,0.76 2.531,0.344 10 false Shift operation of pattern A or pattern B 0.865,1.646 2.25,1.979 1.385,0.333 10 false Accelerator Pedal ON 4.49,4.125 7.021,4.75 2.531,0.625 10 false *: The engine output restricted level differs between pattern A and pattern B.



·

Items Controlled

-

Engine output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift lever is in P or N.



Reverse control

Activation conditions


·

The shift lever is in R.

·

The accelerator pedal is depressed excessively.

A396028E39
3.323,1.344 5.198,0.979 true 4.177,3.25 5.667,2.75 true 4.521,2.885 4.938,2.469 true 4.719,3.542 5.635,3.25 true 1.438,3.167 2.375,3.635 0.938,0.469 10 false Engine Output 3.625,4.042 4.24,4.24 0.615,0.198 10 false Time 5.563,3.073 6.375,3.292 0.813,0.219 10 false with control 5.563,2.573 6.438,2.844 0.875,0.271 10 false Restricted 4.677,2.281 5.615,2.646 0.938,0.365 10 false without control 2.896,2.406 3.677,2.677 0.781,0.271 10 false Activated 1.104,0.781 2.438,1.083 1.333,0.302 10 false Shift Lever Position 1.083,1.271 2.5,1.583 1.417,0.313 10 false Accelerator Pedal ON 1.031,1.656 2.521,2.01 1.49,0.354 10 false Accelerator Pedal OFF 5.25,0.771 7.135,1.365 1.885,0.594 10 false When the accelerator pedal is suddenly depressed. 2.76,0.781 2.917,0.979 0.156,0.198 10 false R


·

Items Controlled

-

Engine output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift lever is moved to any position other than R.




HINT:
·

The engine output restricted level differs between pattern A, pattern B and Reverse control.

·

During reverse control or shift control, engine output is adjusted based on the road gradient and steering angle.




Result:
Result Proceed to
Performed A
Not performed B



A

3.CHECK DTC OUTPUT

B

3.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC is output B



A

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)

B

GO TO DTC CHART

4.READ VALUE USING GTS (FR, FL, RR, RL WHEEL SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / FR Wheel Speed, FL Wheel Speed, RR Wheel Speed and RL Wheel Speed.


f.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle stopped, engine running 0 km/h (0 mph)
Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

5.READ VALUE USING GTS (SPD (SP2))

NG

INSPECT FRONT OR REAR SPEED SENSOR

5.READ VALUE USING GTS (SPD (SP2))
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Powertrain / Engine / Data List / SPD (SP2)


f.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
SPD (SP2) Vehicle stopped, engine running 0 rpm
Vehicle being driven at constant speed between 16.1 to 64.4 km/h (10 to 40 mph) No large fluctuations when driving at a constant speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

6.READ VALUE USING GTS (DECELERATION SENSOR)

NG

6.READ VALUE USING GTS (DECELERATION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Deceleration Sensor and Deceleration Sensor2.


f.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
Deceleration Sensor
Deceleration Sensor2
During deceleration Value changes with vehicle speed
During acceleration Value changes with vehicle speed


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

7.READ VALUE USING GTS (STEERING ANGLE SENSOR)

NG

7.READ VALUE USING GTS (STEERING ANGLE SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Start the engine.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List / Steering Angle Sensor.


f.

Read the value displayed on the GTS.

Standard:
GTS Display Condition Specified Condition
Steering Angle Sensor Steering wheel turned left Value increases with steering wheel operation
Steering wheel turned right Value decreases with steering wheel operation


CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Data can be captured relatively easily by using the snapshot function in the Data List. Confirm the data after performing the drive test.



Result:
Proceed to
OK
NG



OK

NG

8.PAST ACTIVATION CONFIRMATION
a.

Check if the customer operated the vehicle in a way that would cause the drive start control to operate.

HINT:
Drive Start Control Activation Conditions
Shift control

Activation conditions


·

Pattern A (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift lever is moved from P to any forward position (D or S) or R.



·

Pattern B (When all of the following conditions are met, control starts.)

-

The accelerator pedal is open by approximately 1/5 or more.

-

The shift lever is moved from R to any forward position (D or S), any forward position (D or S) to R, or N to R.

A396026E39
4.594,3.958 5.354,3.479 true 4.052,3.5 4.948,3.042 true 4.063,3.042 4.344,2.615 true 2.604,1.719 4.906,1.479 true 3.094,0.99 3.781,0.563 true 3.271,4.115 3.885,4.313 0.615,0.198 10 false Time 5.125,3.313 6.5,3.563 1.375,0.25 10 false with control * 4.198,2.438 5.188,2.708 0.99,0.271 10 false without control 4.833,2.875 5.604,3.167 0.771,0.292 10 false Restricted 2.781,2.51 3.365,2.771 0.583,0.26 10 false Activated 1.156,3.271 2.25,3.635 1.094,0.365 10 false Engine output 0.99,1.198 2.26,1.542 1.271,0.344 10 false Shift Lever Position 0.802,1.958 2.25,2.25 1.448,0.292 10 false Accelerator Pedal OFF 4.948,1.281 6.833,1.938 1.885,0.656 10 false Accelerator pedal is open by approximately 1/5 or more. 3.771,0.417 6.302,0.76 2.531,0.344 10 false Shift operation of pattern A or pattern B 0.865,1.646 2.25,1.979 1.385,0.333 10 false Accelerator Pedal ON 4.49,4.125 7.021,4.75 2.531,0.625 10 false *: The engine output restricted level differs between pattern A and pattern B.



·

Items Controlled

-

Engine output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift lever is in P or N.



Reverse control

Activation conditions


·

The shift lever is in R.

·

The accelerator pedal is depressed excessively.

A396028E40
3.323,1.344 5.198,0.979 true 4.177,3.25 5.667,2.75 true 4.521,2.885 4.938,2.469 true 4.719,3.542 5.635,3.25 true 1.438,3.167 2.375,3.635 0.938,0.469 10 false Engine output 3.625,4.042 4.24,4.24 0.615,0.198 10 false Time 5.563,3.073 6.375,3.292 0.813,0.219 10 false with control 5.563,2.573 6.438,2.844 0.875,0.271 10 false Restricted 4.677,2.281 5.615,2.646 0.938,0.365 10 false without control 2.896,2.406 3.677,2.677 0.781,0.271 10 false Activated 1.104,0.781 2.438,1.083 1.333,0.302 10 false Shift Lever Position 1.083,1.271 2.5,1.583 1.417,0.313 10 false Accelerator Pedal ON 1.031,1.656 2.521,2.01 1.49,0.354 10 false Accelerator Pedal OFF 5.25,0.771 7.135,1.365 1.885,0.594 10 false When the accelerator pedal is suddenly depressed. 2.76,0.781 2.917,0.979 0.156,0.198 10 false R


·

Items Controlled

-

Engine output is restricted.



·

Deactivation Conditions

-

The accelerator pedal is released.

-

The shift lever is moved to any position other than R.




HINT:
·

The engine output restricted level differs between pattern A, pattern B and Reverse control.

·

During reverse control or shift control, engine output is adjusted based on the road gradient and steering angle.




Result:
Result Proceed to
Performed A
Not performed B



A

SYSTEM NORMAL

B

9.CHECK DTC OUTPUT
9.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: System Select / Health Check.


e.

Check the DTCs.


Result:
Result Proceed to
DTCs are not output A
DTC is output B



A

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

B

GO TO DTC CHART

10.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Result:
Result Proceed to
Normal A
Abnormal B



A

11.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)

B

11.READ VALUE USING GTS (ACCELERATOR PEDAL POSITION SENSOR)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Data List / Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %.


e.

Read the value displayed on the GTS.

OK:
GTS Display Condition Specified Condition
Accelerator Position Sensor No.1 Voltage % Accelerator Pedal Released → Depressed Values smoothly change following accelerator pedal operation
Accelerator Position Sensor No.2 Voltage %


HINT:

For numerical values of Accelerator Position Sensor No.1 Voltage % and Accelerator Position Sensor No.2 Voltage %, refer to the Data List.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>DATA LIST / ACTIVE TEST



Result:
Proceed to
OK
NG



OK

NG

REPLACE ACCELERATOR PEDAL(W/SENSOR) ROD ASSEMBLY