Home › Drivetrain › AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE) › AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV) › 2015.06–2017.08
RM27T0E _52 Drivetrain _053698 AC60F AUTOMATIC TRANSMISSION / TRANSAXLE _0260782 AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV) C

AC60F AUTOMATIC TRANSMISSION / TRANSAXLE  AUTOMATIC TRANSMISSION SYSTEM(for 1GD-FTV)  P2774  Four Wheel Drive (4WD) Low Switch Circuit High  


DESCRIPTION

The ECM detects the signal from the transfer L4 position switch.

This DTC indicates that the transfer L4 position switch remains off.

DTC Code DTC Detection Condition Trouble Area
P2774 Transfer L4 position switch remains off while the vehicle is being driven under the following conditions for 1.8 seconds or more (1 trip detection logic):
(a) Output shaft speed is between 1000 and 3000 rpm.
(b) Transfer position switch is in L4.
·

Open in transfer L4 position switch circuit

·

Transfer system

·

ECM



MONITOR DESCRIPTION

The ECM monitors the transfer case L4 position switch to determine when the transfer case L4 gears are engaged. If the transfer case H4 gears remain engaged under the following conditions, the ECM will conclude that there is a malfunction of the L4 position switch, illuminate the MIL and store the DTC:

·

The L4 switch indicates that the H4 transfer case gears are engaged.

·

The transfer position switch is in L4.

·

The transfer case output shaft speed is between 1000 and 3000 rpm.

·

The specified time period has elapsed.


CAUTION / NOTICE / HINT

NOTICE:

Perform registration and/or initialization when parts related to the automatic transmission are replaced.

Click hereDrivetrain>AC60F (AUTOMATIC TRANSMISSION / TRANSAXLE)>AUTOMATIC TRANSMISSION SYSTEM (for 1GD-FTV)>PRECAUTION


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the transfer position switch to L4.

2.

Drive the vehicle at 15 to 20 km/h (9 to 12 mph) for 1.8 seconds or more.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (L4 TERMINAL VOLTAGE)
a.
C209926C06
1.563,0.25 1.896,0.5 0.333,0.25 0.354,1.75 0.51,1.313 true 0.083,0.083 0.396,0.24 0.313,0.156 10 false *a 1.604,0.302 1.917,0.458 0.313,0.156 10 false G53 0.271,1.802 0.583,2 0.313,0.198 10 false L4
*a Front view of wire harness connector
(to 4 Wheel Drive Control ECU)


Disconnect the G53 4 wheel drive control ECU connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-21 (L4) - Body ground Engine switch on (IG) 11 to 14 V



Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
2.CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ECM)
a.

Disconnect the G53 4 wheel drive control ECU connector.


b.

Disconnect the C152 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G53-21 (L4) - C152-12 (L4) Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR