Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › SPIRAL CABLE › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261087 SPIRAL CABLE A

SUPPLEMENTAL RESTRAINT SYSTEMS  SPIRAL CABLE  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.



PROCEDURE

Hide 84306 1.INSPECT SPIRAL CABLE SUB-ASSEMBLY

a.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B495629C01
1.313,1.469 1.615,1.729 0.302,0.26 2.865,3.698 3.125,3.917 0.26,0.219 5.823,1.51 6.042,1.698 0.219,0.188 0.948,1.396 1.542,1.396 1.542,1.396 1.542,1.177 true 0.958,0.792 1.552,0.792 1.552,0.792 1.552,1.115 true 6.042,2.177 5.479,2.177 5.479,2.177 5.729,1.563 true 3.167,3.615 3.615,4.271 true 5.792,1.49 6.521,1.167 true 2.583,3.167 3.135,3.531 true 1.469,1.729 1.469,2.292 true 3,3.917 3,4.479 true 6.042,1.604 6.458,1.604 true 1.854,0.417 2.198,0.74 0.344,0.323 12 false *A 0.76,1.302 1.073,1.458 0.313,0.156 10 false *a 1.406,2.333 1.719,2.49 0.313,0.156 10 false *b 3.583,4.292 3.896,4.448 0.313,0.156 10 false *c 0.771,0.698 1.083,0.854 0.313,0.156 10 false *d 5.323,0.406 5.667,0.729 0.344,0.323 12 false *B 3.458,2.646 3.802,2.969 0.344,0.323 12 false *C 6.094,2.094 6.406,2.25 0.313,0.156 10 false *d 6.563,1.052 6.875,1.208 0.313,0.156 10 false *a 2.406,3.052 2.719,3.208 0.313,0.156 10 false *a 2.948,4.521 3.26,4.677 0.313,0.156 10 false *b 6.521,1.531 6.833,1.688 0.313,0.156 10 false *b
*A Flat Cable (Visible Type), w/o Steering Haeter *B Flat Cable (Visible Type), w/ Steering Heater
*C Colored Roller (Visible Type) - -
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn



b.

If the spiral cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral cable sub-assembly .

·

When rotating the spiral cable sub-assembly , make sure to push on the interlock to release the interlock.

·

Do not turn the spiral cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B459513C01
0,0 0,0 false
V100144

Interlock
V100135

Counterclockwise


While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

Make sure to rotate the spiral cable sub-assembly counterclockwise. If rotated clockwise, it may be damaged or centering may no longer be possible.


HINT:

The interlock operates at the top and bottom of the connector.



ii.
B459514

If the spiral cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B459515C01
0,0 0,0 false
V100144

Interlock
V100135

Counterclockwise


While pushing on the interlock, rotate the spiral cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.




c.

Check that the spiral cable sub-assembly is center position.

OK:

The connector is at the top.

The matchmarks are aligned.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B495629C01
1.313,1.469 1.615,1.729 0.302,0.26 2.865,3.698 3.125,3.917 0.26,0.219 5.823,1.51 6.042,1.698 0.219,0.188 0.948,1.396 1.542,1.396 1.542,1.396 1.542,1.177 true 0.958,0.792 1.552,0.792 1.552,0.792 1.552,1.115 true 6.042,2.177 5.479,2.177 5.479,2.177 5.729,1.563 true 3.167,3.615 3.615,4.271 true 5.792,1.49 6.521,1.167 true 2.583,3.167 3.135,3.531 true 1.469,1.729 1.469,2.292 true 3,3.917 3,4.479 true 6.042,1.604 6.458,1.604 true 1.854,0.417 2.198,0.74 0.344,0.323 12 false *A 0.76,1.302 1.073,1.458 0.313,0.156 10 false *a 1.406,2.333 1.719,2.49 0.313,0.156 10 false *b 3.583,4.292 3.896,4.448 0.313,0.156 10 false *c 0.771,0.698 1.083,0.854 0.313,0.156 10 false *d 5.323,0.406 5.667,0.729 0.344,0.323 12 false *B 3.458,2.646 3.802,2.969 0.344,0.323 12 false *C 6.094,2.094 6.406,2.25 0.313,0.156 10 false *d 6.563,1.052 6.875,1.208 0.313,0.156 10 false *a 2.406,3.052 2.719,3.208 0.313,0.156 10 false *a 2.948,4.521 3.26,4.677 0.313,0.156 10 false *b 6.521,1.531 6.833,1.688 0.313,0.156 10 false *b
*A Flat Cable (Visible Type), w/o Steering Haeter *B Flat Cable (Visible Type), w/ Steering Heater
*C Colored Roller (Visible Type) - -
*a Check Window *b Matchmark
*c Colored Roller *d Top of Flat Cable U-turn


NOTICE:

If the spiral cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.



Hide 89245B 2.INSTALL STEERING SENSOR (w/ Steering Sensor)

HINT:

Perform this procedure only when replacement of the spiral cable sub-assembly is necessary.


a.

Install the steering sensor to a new spiral cable sub-assembly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>STEERING ANGLE SENSOR>INSTALLATION


Hide 84307 3.INSTALL SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY (w/ Steering Sensor)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Attach the 3 claws to install the spiral cable with sensor sub-assembly.

CAUTION:

When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.



d.

Connect the connectors to the spiral cable with sensor sub-assembly.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



Hide 84306 4.INSTALL SPIRAL CABLE SUB-ASSEMBLY (w/o Steering Sensor)

a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Attach the 3 claws to install the spiral cable sub-assembly.


d.

Connect the connectors to the spiral cable sub-assembly.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.



Hide 45286B 5.INSTALL UPPER STEERING COLUMN COVER

a.

for Manual Tilt and Manual Telescopic Steering Column:



b.

for Power Tilt and Power Telescopic Steering Column:



Hide 45287 6.INSTALL LOWER STEERING COLUMN COVER

a.

for Manual Tilt and Manual Telescopic Steering Column:



b.

for Power Tilt and Power Telescopic Steering Column:



Hide 7. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

Hide 84306 8.ADJUST SPIRAL CABLE SUB-ASSEMBLY

NOTICE:

Do not adjust the spiral with sensor cable sub-assembly with the battery connected and the ignition switch ON.


a.

Check that the ignition switch is off.


b.

Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



c.

Check that the spiral with sensor cable sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B495636C01
2.271,4.229 2.979,4.573 true 1.51,3.667 2.219,4.01 true 6.458,2.563 6.771,1.938 true 0.948,2.281 0.635,2.906 true 0.531,1.594 0.948,2.177 true 6.396,2.656 5.958,3.25 true 1.74,0.271 2.156,0.656 0.417,0.385 12 false *A 1.333,3.552 1.646,3.708 0.313,0.156 10 false *a 3.031,4.521 3.344,4.677 0.313,0.156 10 false *b 0.375,1.448 0.688,1.604 0.313,0.156 10 false *c 5.302,0.281 5.719,0.667 0.417,0.385 12 false *B 3.458,2.521 3.875,2.906 0.417,0.385 12 false *C 0.542,2.927 0.854,3.083 0.313,0.156 10 false *a 6.781,1.781 6.979,1.99 0.198,0.208 10 false *a 5.844,3.24 6.156,3.396 0.313,0.156 10 false *c
*A Flat Cable (Visible Type), w/o Steering Haeter *B Flat Cable (Visible Type), w/ Steering Heater
*C Colored Roller (Visible Type) - -
*a Check Window *b Colored Roller
*c Top of Flat Cable U-turn - -



d.

If the spiral with sensor cable sub-assembly is not centered, center it.

NOTICE:

Failure to observe the following precautions may result in damage to the spiral with sensor cable sub-assembly.

·

When rotating the spiral with sensor cable sub-assembly, make sure to push on the interlock to release the interlock.

·

Do not turn the spiral with sensor cable sub-assembly using the airbag wire harness.

·

Do not forcibly rotate the part.



i.
B495633C01
0,0 0,0 false
V100144

Interlock
V100135

Counterclockwise


While pushing on the interlock indicated in the illustration. Make sure to rotate the spiral with sensor cable sub-assembly counterclockwise slowly by hand until it stops.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral with sensor cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



ii.
B495634

If the spiral with sensor cable sub-assembly stops rotating and the connector has moved past the bottom, return the connector to the bottom as shown in the illustration.


iii.
B495635C01
0,0 0,0 false
V100144

Interlock
V100135

Clockwise


While pushing on the interlock, rotate the spiral with sensor cable sub-assembly clockwise approximately 2.5 times to move the connector from the bottom to the top.

NOTICE:

If the connector is rotated clockwise from the bottom 5 times or more, the spiral with sensor cable sub-assembly may be damaged.


HINT:

The interlock operates at the top and bottom of the connector.



iv.

Check that the spiral with sensor cable sub-assembly is center position.

OK:

The connector is at the top.

The colored roller or the top of the flat cable U-turn can be checked from the check window.


B488759C02
1.583,1.948 2,2.281 0.417,0.333 4.323,2.135 4.615,2.135 4.615,2.135 5.302,1.99 true 1.99,1.688 2.938,1.688 true 1.031,2 1.292,2 1.292,2 1.979,1.76 true 5.365,1.938 5.156,1.771 5.156,1.771 4.25,1.771 true 5.5,2.115 6.417,1.854 6.417,1.854 5.427,2.052 true 0.354,0.031 0.719,0.229 0.365,0.198 12 false *A 3.75,0.031 4.021,0.24 0.271,0.208 12 false *B 0.875,1.896 1.188,2.052 0.313,0.156 10 false *a 1.594,1.958 1.781,2.135 0.188,0.177 10 true *b 2.99,1.625 3.302,1.781 0.313,0.156 10 false *c 4.083,1.667 4.396,1.823 0.313,0.156 10 false *a 4.177,2.042 4.49,2.198 0.313,0.156 10 false *c 6.438,1.792 6.688,2.01 0.25,0.219 10 false *b
*A w/o Steering Heater *B w/ Steering Heater
*a Check Window *b Matchmark
*c Top of Flat Cable U-turn - -


NOTICE:

If the spiral with sensor cable sub-assembly cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.




Hide 45100 9.INSTALL STEERING WHEEL ASSEMBLY

a.

Install the steering wheel assembly (See page Steering>STEERING COLUMN>STEERING WHEEL>INSTALLATION).


Hide 10.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Hide 11. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


Hide 12.CHECK SRS WARNING LIGHT