Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
89834
1.INSTALL REAR AIRBAG SENSOR LH
Check that the ignition switch is off.
Check that the cable is disconnected from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Install the rear airbag sensor with the nut.
If the rear airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
When installing the rear airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.
Check that the rear airbag sensor is not loose.
Connect the connector.
64740C
2.INSTALL DECK TRIM SIDE PANEL ASSEMBLY LH
73233A
3.INSTALL OUTER LAP BELT COVER
64712F
4.INSTALL FRONT DECK SIDE TRIM COVER (w/ Tonneau Cover)
64937A
5.INSTALL NO. 1 TONNEAU COVER HOLDER CAP (w/o Tonneau Cover)
64725D
6.INSTALL NO. 1 LUGGAGE COMPARTMENT TRIM HOOK
58570C
7.INSTALL REAR FLOOR CARPET ASSEMBLY
62538E
8.INSTALL QUARTER TRIM COVER HOLE LH
58574A
9.INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
58649C
10.INSTALL MAT SET PLATE COVER
64910M
11.INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
62312B
12.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH
67920
13.INSTALL DOOR SCUFF PLATE ASSEMBLY LH
14.INSTALL REAR NO. 1 SEAT ASSEMBLY
for 60/40 Split Double-folding Seat Type LH Side:
Install the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type LH Side)>INSTALLATION).
for 60/40 Split Double-folding Seat Type RH Side:
Install the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Double-folding Seat Type RH Side)>INSTALLATION).
for 60/40 Split Tumble Seat Type LH Side:
Install the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Tumble Seat Type LH Side)>REMOVAL).
for 60/40 Split Tumble Seat Type RH Side:
Install the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY(for 60/40 Split Tumble Seat Type RH Side)>INSTALLATION).
for 60/40 Split Slide Walk-in Seat Type LH Side:
Install the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type LH Side)>INSTALLATION).
for 60/40 Split Slide Walk-in Seat Type RH Side:
Install the rear No. 1 seat assembly (See page Vehicle Interior>SEAT>REAR NO. 1 SEAT ASSEMBLY (for 60/40 Split Slide Walk-in Seat Type RH Side)>INSTALLATION).
15.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
16. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
17.CHECK SRS WARNING LIGHT
Check the SRS warning light (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).