Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
67492A
3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH
Detach the 2 clips and remove the front door lower frame bracket garnish LH.
69298A
4.REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH
Using a moulding remover, detach the 3 claws and remove the inside handle bezel LH as shown in the illustration.
74611C
5.REMOVE ASSIST GRIP COVER LH
Using moulding remover A, detach the 8 claws and remove the assist grip cover LH.
67602
6.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
Remove the 12 clips.
| *a | Reference Boss |
Pull out the front door trim board sub-assembly LH in the direction indicated by the arrow in the illustration.
Raise the front door trim board sub-assembly LH to detach the 4 claws and remove the front door trim board sub-assembly LH together with the front door inner glass weatherstrip LH.
Disconnect the 2 connectors.
w/ Seat Position Memory System:
Disconnect the connector.
Disconnect the front door lock remote control cable assembly LH and front door inside locking cable assembly LH.
68172A
7.REMOVE FRONT DOOR INNER GLASS WEATHERSTRIP LH
Using a screwdriver, detach the 4 claws and remove the front door inner glass weatherstrip LH from the front door trim board sub-assembly LH as shown in the illustration.
81910A
8.REMOVE FRONT REFLEX REFLECTOR ASSEMBLY
Detach the 2 claws and remove the front reflex reflector assembly.
81080E
9.REMOVE FRONT DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH (w/ Personal Light)
81080L
10.REMOVE NO. 1 INTERIOR ILLUMINATION LIGHT ASSEMBLY LH (w/ Personal Light)
84927
11.REMOVE SEAT MEMORY SWITCH (w/ Seat Position Memory System)
84040
12.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (for Driver Side)
Remove the 3 screws and the multiplex network master switch assembly.
84810
13.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY (for Front Passenger Side)
69206B
14.REMOVE FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Remove the 8 screws and door assist grip assembly LH.
Remove the 2 screws.
Detach the guide and 2 claws and remove the front door inside handle sub-assembly LH from the front door trim board sub-assembly LH.
89430A
15.REMOVE OUTER MIRROR CONTROL ECU ASSEMBLY LH (w/ Reverse Shift-linked Mirror)
86160
16.REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
89860A
17.REMOVE SIDE AIRBAG SENSOR ASSEMBLY LH
67832
18.REMOVE FRONT DOOR SERVICE HOLE COVER LH
Remove the bolt.
Detach the 2 clamps, move the wire harness out of the way and remove the front door service hole cover LH.
Remove any remaining butyl tape from the front door panel.
87940
19.REMOVE OUTER REAR VIEW MIRROR ASSEMBLY LH
68102
20.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY LH
Connect the cable to the negative (-) battery terminal.
Connect the multiplex network master switch assembly and move the front door glass sub-assembly LH so that the door glass bolts can be seen.
Disconnect the cable from the negative (-) battery terminal and multiplex network master switch assembly.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Remove the 2 bolts.
After the bolts are removed, do not allow the front door glass sub-assembly LH to fall.
Remove the front door glass sub-assembly LH as indicated by the arrows in the order shown in the illustration.
Do not damage the front door glass sub-assembly LH.
69802
21.REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH
| *1 | Temporary Bolt |
Disconnect the connector.
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the front door window regulator sub-assembly LH may fall and cause damage.
Remove the 5 bolts.
Remove the front door window regulator sub-assembly LH.
Remove the temporary bolt from the front door window regulator sub-assembly LH.
85720C
22.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
68151D
23.REMOVE FRONT DOOR GLASS RUN LH
Remove the front door glass run LH.
67664C
24.REMOVE DOOR FRAME GARNISH LH
Detach the clip and remove the door frame garnish LH.
67404F
25.REMOVE FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH
Remove the bolt and front door rear lower frame sub-assembly LH as shown in the illustration.
26.REMOVE FRONT DOOR OUTSIDE HANDLE COVER WITH LOCK CYLINDER ASSEMBLY (for Driver Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover with lock cylinder assembly.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly LH.
69217D
27.REMOVE FRONT DOOR OUTSIDE HANDLE COVER LH (for Driver Side)
Using a screwdriver, detach the claw and remove the front door outside handle cover LH.
69217D
28.REMOVE FRONT DOOR OUTSIDE HANDLE COVER RH (for Front Passenger Side)
Remove the hole plug.
Using a T30 "TORX" socket wrench, loosen the screw and remove the front door outside handle cover RH.
The screw cannot be removed because it is integrated into the front door outside handle frame sub-assembly RH.
69220
29.REMOVE FRONT DOOR OUTSIDE HANDLE ASSEMBLY LH
w/ Entry and Start System:
Detach the 2 claws.
Disconnect the connector.
Move the lever in the direction indicated by the arrow in the illustration.
Remove the front door outside handle assembly LH as shown in the illustration.
69252
30.REMOVE FRONT DOOR FRONT OUTSIDE HANDLE PAD LH
Detach the 3 claws and remove the front door front outside handle pad LH.
69254C
31.REMOVE FRONT DOOR REAR OUTSIDE HANDLE PAD LH
Detach the 2 claws and remove the front door rear outside handle pad LH.
69040A
32.REMOVE FRONT DOOR LOCK ASSEMBLY LH
69720B
33.REMOVE FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
Remove the front door lock remote control cable assembly LH.
69760C
34.REMOVE FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH
Using a screwdriver, detach the 3 claws.
Tape the screwdriver tip before use.
Remove the front door inside locking cable assembly LH.
69202A
35.REMOVE FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
w/ Entry and Start System:
Disconnect the connector.
Detach the clamp and remove the front door wire LH.
Using a T30 "TORX" socket wrench, loosen the screw.
Slide the front door outside handle frame sub-assembly LH to detach the door handle nut and claw of the front door outside handle frame sub-assembly LH, and then remove the front door outside handle frame sub-assembly LH.
82152A
36.REMOVE FRONT DOOR WIRE LH (w/ Entry and Start System)
Detach the 4 clamps and remove the front door wire LH.
69312
37.REMOVE FRONT DOOR LOCK OPEN ROD LH
Remove the front door lock open rod LH as indicated by the arrows, in the order shown in the illustration.
67924
38.REMOVE FRONT DOOR NO. 2 STIFFENER CUSHION
| *a | Double-sided Tape |
Remove the 2 bolts.
Detach the 2 claws and remove the front door No. 2 stiffener cushion.
68620
39.REMOVE FRONT DOOR CHECK ASSEMBLY LH
Remove the bolt, 2 nuts and front door check assembly LH.
67862
40.REMOVE FRONT DOOR WEATHERSTRIP LH
Using a clip remover, detach the 21 clips and remove the front door weatherstrip LH.
75712B
41.REMOVE FRONT DOOR BELT MOULDING LH
75756C
42.REMOVE FRONT DOOR REAR WINDOW FRAME MOULDING LH
75922M
43.REMOVE NO. 1 BLACK OUT TAPE LH
75986F
44.REMOVE FRONT DOOR OUTSIDE STRIPE LH
75976G
45.REMOVE NO. 2 FRONT DOOR STRIPE LH
67001A
46.REMOVE FRONT DOOR PANEL CUSHION
Using a clip remover, detach the clip and remove the door panel cushion.