Use the same procedure for RHD and LHD vehicles.
The procedure listed below is for LHD vehicles.
Use the same procedure for the RH and LH sides.
The procedure listed below is for the LH side.
1. PRECAUTION
Be sure to read Precaution thoroughly before servicing.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
69298A
3.REMOVE NO. 2 DOOR INSIDE HANDLE BEZEL LH
Using moulding remover A, detach the 3 claws and remove the rear door inside handle bezel as shown in the illustration.
74611C
4.REMOVE ASSIST GRIP COVER LH
Using moulding remover A, detach the 8 claws and remove the assist grip cover.
67604
5.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
Remove the 3 screws.
Using a clip remover, detach the 9 clips.
Pull out the rear door trim board sub-assembly in the direction indicated by the arrow in the illustration.
Raise the rear door trim board sub-assembly to detach the 4 claws and remove the rear door trim board sub-assembly together with the rear door inner glass weatherstrip.
Disconnect the rear door lock remote control cable assembly and rear door inside locking cable assembly as shown in the illustration.
| *A | for 14 Speakers |
| *B | for 9 Speakers |
Disconnect each connector.
Using a screwdriver, detach the claw and remove the clamp.
68174A
6.REMOVE REAR DOOR INNER GLASS WEATHERSTRIP LH
Using a screwdriver, detach the 3 claws and remove the rear door inner glass weatherstrip from the rear door trim board sub-assembly as shown in the illustration.
84810D
7.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY
81910D
8.REMOVE REAR REFLEX REFLECTOR ASSEMBLY
Detach the 2 claws and remove the rear reflex reflector assembly.
81080G
9.REMOVE REAR DOOR INSIDE HANDLE ILLUMINATION LIGHT ASSEMBLY LH
81081A
10.REMOVE NO. 2 INTERIOR ILLUMINATION LIGHT SUB-ASSEMBLY
69206C
11.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH
Remove the 8 screws and rear door armrest.
Remove the 2 screws.
Detach the guide and 2 claws and remove the rear door inside handle sub-assembly from the rear door trim board sub-assembly.
86160Y
12.REMOVE REAR NO. 2 SPEAKER ASSEMBLY (for 14 Speakers)
86160C
13.REMOVE REAR SPEAKER SET
67842E
14.REMOVE REAR DOOR SERVICE HOLE COVER
Disconnect the connector.
Detach the 3 clamps, move the wire harness out of the way and remove the service hole cover.
Remove any remaining butyl tape from the door.
68152C
15.REMOVE REAR DOOR GLASS RUN LH
Remove the rear door glass run.
67674A
16.REMOVE REAR DOOR FRAME GARNISH LH
Detach the clip and remove the rear door frame garnish.
67408E
17.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY LH
| *1 | Temporary Bolt |
Loosen the temporary bolt.
Remove the 2 bolts and screw.
Remove the rear door window division bar sub-assembly.
Remove the temporary bolt from the rear door window division bar sub-assembly.
68124B
18.REMOVE REAR DOOR QUARTER WINDOW GLASS LH
Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.
68189
19.REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
Remove the rear door quarter window weatherstrip from the rear door quarter window glass.
68104
20.REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH
Connect the cable to the negative (-) battery terminal and rear power window regulator motor connector.
Connect the power window regulator switch assembly and move the rear door glass sub-assembly so that the door glass bolts can be seen.
Disconnect the power window regulator switch assembly and rear power window regulator motor connectors.
Disconnect the cable from the negative (-) battery terminal.
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
After the bolts are removed, do not allow the door glass to fall.
Remove the rear door glass sub-assembly as indicated by the arrows in the order shown in the illustration.
Do not damage the door glass.
69906B
21.REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH
| *1 | Protective Tape |
Using a screwdriver, remove the rear door glass channel sub-assembly.
Tape the screwdriver tip before use.
69975A
22.REMOVE REAR DOOR GLASS CHANNEL FILLER
Remove the rear door glass channel filler.
69840A
23.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY LH
| *1 | Temporary Bolt |
Loosen the temporary bolt.
Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.
Remove the 3 bolts.
Remove the rear door window regulator assembly.
Remove the temporary bolt from the rear door window regulator assembly.
85720C
24.REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
69340
25.REMOVE REAR DOOR LOCK ASSEMBLY LH
69740D
26.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH
| *A | w/ Double Locking System |
| *B | w/o Double Locking System |
Using a screwdriver, detach the claw.
Tape the screwdriver tip before use.
| *A | w/ Double Locking System |
| *B | w/o Double Locking System |
Remove the rear door lock remote control cable assembly.
69780B
27.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH
| *A | w/ Double Locking System |
| *B | w/o Double Locking System |
Using a screwdriver, detach the 3 claws.
Tape the screwdriver tip before use.
| *A | w/ Double Locking System |
| *B | w/o Double Locking System |
Remove the rear door inside locking cable assembly.
69227L
28.REMOVE REAR DOOR OUTSIDE HANDLE COVER LH
Using a T30 "TORX" socket wrench, loosen the screw.
The screw cannot be removed because it is integrated into the rear door outside handle frame sub-assembly.
Detach the claw and remove the rear door outside handle cover.
69240
29.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH
Move the lever in the direction indicated by the arrow in the illustration.
Remove the rear door outside handle assembly as shown in the illustration.
69252B
30.REMOVE REAR DOOR NO. 1 OUTSIDE HANDLE PAD LH
Detach the 3 claws and remove the rear door No. 1 outside handle pad.
69254B
31.REMOVE REAR DOOR NO. 2 OUTSIDE HANDLE PAD LH
Detach the 2 claws and remove the rear door No. 2 outside handle pad.
69204A
32.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
Using a T30 "TORX" socket wrench, loosen the screw.
Slide the rear door outside handle frame sub-assembly to detach the door handle nut and claw of the rear door outside handle frame sub-assembly, and then remove the rear door outside handle frame sub-assembly.
67888A
33.REMOVE REAR DOOR NO. 2 WEATHERSTRIP LH
Using a clip remover, detach the 6 clips and guide and remove the rear door No. 2 weatherstrip as shown in the illustration.
68640A
34.REMOVE REAR DOOR CHECK ASSEMBLY LH
Remove the bolt, 2 nuts and rear door check assembly.
67872
35.REMOVE REAR DOOR WEATHERSTRIP LH
Using a clip remover, detach the 19 clips and guide and remove the rear door weatherstrip.
75722A
36.REMOVE REAR DOOR BELT MOULDING LH
75762A
37.REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH
75924C
38.REMOVE NO. 2 BLACK OUT TAPE LH
75978H
39.REMOVE REAR DOOR LOWER OUTSIDE STRIPE LH
75928A
40.REMOVE BLACK OUT TAPE LH
75988E
41.REMOVE REAR DOOR OUTSIDE STRIPE LH
67003C
42.REMOVE REAR DOOR PANEL CUSHION
Using a clip remover, detach the clip and remove the door panel cushion.