The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed, installed, or replaced during the automatic transmission assembly removal/installation are shown below.
When the cable is disconnected / reconnected to the battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.
Learning completes when vehicle is driven
To prevent burns, do not touch the engine, exhaust pipe or other high temperature components while the engine is hot.
| *a | Object Exceeding Weight Limit of Transmission Jack |
The automatic transmission assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the transmission jack may suddenly drop or a part may fall.
1. PRECAUTION
After turning the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.
(See pageGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION)
2.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
51405A
3.REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
51450
4.REMOVE REAR ENGINE UNDER COVER ASSEMBLY
5.DRAIN AUTOMATIC TRANSMISSION FLUID
6.DRAIN TRANSFER OIL
7.REMOVE PROPELLER SHAFT ASSEMBLY
37140
8.REMOVE FRONT PROPELLER SHAFT ASSEMBLY
17410
9.REMOVE FRONT EXHAUST PIPE ASSEMBLY
28100
10.REMOVE STARTER ASSEMBLY
11354
11.REMOVE FLYWHEEL HOUSING DUST SEAL
Remove the flywheel housing dust seal from the engine assembly.
32101A
12.REMOVE DRIVE PLATE AND TORQUE CONVERTER ASSEMBLY SETTING BOLT
Turn the crankshaft to gain access to the locations of the 6 drive plate and torque converter assembly setting bolts and remove each bolt while holding the crankshaft pulley bolt with a wrench.
There will be one black colored bolt.
17118
13.REMOVE MANIFOLD STAY
Remove the 3 bolts and manifold stay from the automatic transmission assembly and exhaust manifold.
33820B
14.DISCONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
Remove the clip and nut and disconnect the transmission control cable assembly from the transmission control shaft lever LH and transmission control cable bracket.
35979B
15.REMOVE TRANSMISSION INSULATOR RH
82046A
16.DISCONNECT NO. 1 BODY GROUND WIRE SUB-ASSEMBLY
Remove the bolt and disconnect the No. 1 body ground wire sub-assembly from the automatic transmission assembly.
17.DISCONNECT OIL COOLER TUBE
Disconnect the 2 oil cooler tubes from the automatic transmission assembly.
Use a container to catch any ATF.
Remove the bolt and flexible hose clamp.
| *1 | Flexible Hose Clamp | - | - |
Remove the 2 bolts and disconnect the 2 oil cooler tubes from the engine assembly.
51225B
18.REMOVE FRONT SUSPENSION MEMBER BRACKET LH AND RH
Remove the 8 bolts, front suspension member bracket LH and RH from the No. 3 frame crossmember sub-assembly and vehicle body.
35000
19.SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY
Support the automatic transmission assembly with a transmission jack.
In order to protect the automatic transmission oil pan sub-assembly, place attachments on the transmission jack.
Make sure that the attachments and the automatic transmission oil pan sub-assembly are centered on the transmission jack.
To prevent the automatic transmission oil pan sub-assembly from deforming, do not place any attachments under the automatic transmission oil pan sub-assembly of the automatic transmission assembly.
Secure the automatic transmission assembly to the transmission jack using a belt, etc. to prevent it from falling.
51203
20.REMOVE NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
Remove the 4 bolts and disconnect the No. 3 frame crossmember sub-assembly from the rear engine mounting insulator.
Remove the 4 bolts, 4 nuts and No. 3 frame crossmember sub-assembly from the vehicle body.
12371
21.REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR
It is not necessary to remove the rear engine mounting insulator unless it is being replaced.
Remove the 4 bolts and rear No. 1 engine mounting insulator from the automatic transmission assembly.
36478A
22.REMOVE TRANSMISSION BREATHER BRACKET
Tilt down the automatic transmission assembly.
Make sure that the cooling fan and fan shroud do not contact the engine assembly when tilting the automatic transmission assembly.
Disconnect the 3 breather hoses from the transmission breather bracket.
Remove the bolt and disconnect the transmission breather bracket from the automatic transmission assembly.
Detach the wire harness clamp from the transmission breather bracket.
Remove the 2 clamps from the transmission breather bracket.
It is not necessary to remove the transmission clamps they are being replaced.
23.DISCONNECT WIRE HARNESS
Disconnect the breather hose from the wire harness.
Disconnect the park/neutral position switch connector, transmission wire connector, 2 speed sensor connectors and transfer connector.
Detach the claw, press down the lever, and then disconnect the transmission wire connector.
Detach the heated oxygen sensor connector from the wire harness clamp bracket.
Remove the 3 bolts and disconnect the wire harness from the automatic transmission assembly.
35000
24.REMOVE AUTOMATIC TRANSMISSION ASSEMBLY
Disconnect the breather hose from the engine assembly.
Remove the 7 bolts and automatic transmission assembly from the engine assembly.
To prevent damage to the 2 knock pins, do not pry between the automatic transmission assembly and engine assembly.
36100
25.REMOVE TRANSFER ASSEMBLY
33823
26.REMOVE TRANSMISSION CONTROL CABLE BRACKET
It is not necessary to remove the transmission control cable bracket unless it is being replaced.
Remove the 2 bolts and transmission control cable bracket from the automatic transmission assembly.
3516A
27.REMOVE TRANSMISSION OIL PAN HEAT INSULATOR
It is not necessary to remove the transmission oil pan heat insulator unless it is being replaced.
Remove the 3 bolts and transmission oil pan heat insulator from the automatic transmission assembly.
32000
28.REMOVE TORQUE CONVERTER ASSEMBLY
Put matchmarks on the automatic transmission case sub-assembly and the torque converter assembly.
| *a | Matchmark |
Remove the torque converter assembly from the automatic transmission assembly.
Remove the torque converter assembly from the input shaft horizontally.
82715J
29.REMOVE WIRING HARNESS CLAMP BRACKET
It is not necessary to remove the wire harness clamp brackets unless they are being replaced.
Detach the 8 wire harness clamps and 4 wire harness clamp brackets from the wire harness.
32000
30.INSPECT TORQUE CONVERTER ASSEMBLY
31.INSPECT DRIVE PLATE