Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  P013013  O2 (A/F) Sensor Circuit Bank 1 Sensor 1 Circuit Open  P220011  NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Short to Ground  P220012  NOx Sensor Circuit High Bank 1 Sensor 1 Circuit Short to Battery  P220013  NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Open  P220512  NOx Sensor Heater Control Circuit High Bank 1 Sensor 1 Circuit Short to Battery  P220514  NOx Sensor Heater Control Circuit Low Bank 1 Sensor 1 Circuit Short to Ground or Open  


DESCRIPTION

A No. 1 nitrogen oxides sensor is installed in the exhaust manifold converter sub-assembly in order to detect the concentration of NOx and O2 in the exhaust gas.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P013013 O2 (A/F) Sensor Circuit Bank 1 Sensor 1 Circuit Open No. 1 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic)
No. 1 nitrogen oxides sensor Comes on DTC stored SAE Code: P0130
P220011 NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Short to Ground No. 1 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic)
No. 1 nitrogen oxides sensor Comes on DTC stored SAE Code: P2202
P220012 NOx Sensor Circuit High Bank 1 Sensor 1 Circuit Short to Battery No. 1 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic)
No. 1 nitrogen oxides sensor Comes on DTC stored SAE Code: P2203
P220013 NOx Sensor Circuit Low Bank 1 Sensor 1 Circuit Open No. 1 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic)
No. 1 nitrogen oxides sensor Comes on DTC stored SAE Code: P2200
P220512 NOx Sensor Heater Control Circuit High Bank 1 Sensor 1 Circuit Short to Battery No. 1 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic)
No. 1 nitrogen oxides sensor Comes on DTC stored SAE Code: P2207
P220514 NOx Sensor Heater Control Circuit Low Bank 1 Sensor 1 Circuit Short to Ground or Open No. 1 nitrogen oxides sensor malfunction for 3 seconds or more.
(2 trip detection logic)
No. 1 nitrogen oxides sensor Comes on DTC stored SAE Code: P2206

Related Data List
DTC No. Data List
P013013
P220011
P220012
P220013
P220512
P220514
NOx Density B1S1

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P013013
P220011
P220012
P220013
P220512
P220514
Engine switch on (IG) for 3 seconds or more

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P013013, P220011, P220012, P220013, P220512 OR P220514)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Read the DTCs.

Result:
Result Proceed to
DTC P013013, P220011, P220012, P220013, P220512 or P220514 is output A
DTC P013013, P220011, P220012, P220013, P220512 or P220514 and other DTCs are output* B


HINT:

*: If any other DTCs are output, perform troubleshooting for those DTCs first.




A

2.REPLACE NO. 1 NITROGEN OXIDES SENSOR

B

2.REPLACE NO. 1 NITROGEN OXIDES SENSOR
a.

Replace the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>NITROGEN OXIDES SENSOR>REMOVAL

HINT:

Perform "A/F Sensor Learning Value Clear" after replacing the No. 1 nitrogen oxides sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and GTS on.


c.

Clear the DTCs.


d.

Turn the engine switch off and wait for at least 30 seconds.


e.

Turn the engine switch on (IG) for 3 seconds or more.


f.

Confirm that the pending DTC is not output again.

HINT:

Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.


i.

Enter the following menus: Powertrain / Engine / Utility / All Readiness.


ii.

Input DTC P013013, P220011, P220012, P220013, P220512 or P220514.


iii.

Check that STATUS is NORMAL. If STATUS is INCOMPLETE, turn the engine switch on (IG) for 3 seconds or more, and then check "All Readiness" again.



Result:
Proceed to
NEXT



NEXT

END