Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ Urea SCR System) › 2020.08–2021.06
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260461 ECD SYSTEM(w/ Urea SCR System) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ Urea SCR System)  U029D87  Lost Communication with NOx Sensor "A" Missing Message  U029E87  Lost Communication with NOx Sensor "B" Missing Message  U02A387  Lost Communication with PM Sensor Missing Message  


DESCRIPTION

The ECM sends and receives data to and from the No. 1 nitrogen oxides sensor, No. 2 nitrogen oxides sensor and particulate matter sensor* via local CAN communication.

HINT:

*: w/ Particulate matter sensor


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
U029D87 Lost Communication with NOx Sensor "A" Missing Message Communication stops between the ECM and the No. 1 nitrogen oxides sensor for 1 second or more.
(1 trip detection logic)
·

No. 1 nitrogen oxides sensor

·

Harness or connector

·

ECM


Comes on DTC stored SAE Code: U029D
U029E87 Lost Communication with NOx Sensor "B" Missing Message Communication stops between the ECM and the No. 2 nitrogen oxides sensor for 1 second or more.
(1 trip detection logic)
·

No. 2 nitrogen oxides sensor

·

Harness or connector

·

ECM


Comes on DTC stored SAE Code: U029E
U02A387 Lost Communication with PM Sensor Missing Message Communication stops between the ECM and the particulate matter sensor for 1.6 seconds or more.
(1 trip detection logic)
·

Particulate matter sensor

·

Harness or connector

·

ECM


Comes on DTC stored SAE Code: U02A3

MONITOR DESCRIPTION

The ECM stores a DTC when a communication malfunction occurs between the No. 1 nitrogen oxides sensor, No. 2 nitrogen oxides sensor, particulate matter sensor* and ECM.

HINT:

*: w/ Particulate matter sensor


CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
U029D87
U029E87
Engine switch on (IG) and wait for 1 second or more.
U02A387 Engine switch on (IG) and wait for 1.6 seconds or more.

WIRING DIAGRAM

A474997E05
3.865,4.208 4.479,4.406 0.615,0.198 10 false s6 3.865,4.396 6.406,4.646 2.542,0.25 10 false No. 2 Nitrogen Oxides Sensor 3.656,0.823 4.271,1.021 0.615,0.198 10 false C181 3.646,1 6.188,1.25 2.542,0.25 10 false No. 1 Nitrogen Oxides Sensor 3.802,2.646 6.344,2.896 2.542,0.25 10 false Particulate Matter Sensor* 4.344,2.198 4.958,2.396 0.615,0.198 10 false GND 4.354,0.677 4.969,0.875 0.615,0.198 10 false GND 4.354,0.26 4.969,0.458 0.615,0.198 10 false BATT 4.896,0.219 5.51,0.417 0.615,0.198 10 false CAN+ 4.896,0.667 5.51,0.865 0.615,0.198 10 false CAN- 4.885,1.74 5.5,1.938 0.615,0.198 10 false CAN+ 4.885,2.208 5.5,2.406 0.615,0.198 10 false CAN- 4.875,3.458 5.49,3.656 0.615,0.198 10 false CAN+ 4.917,3.969 5.531,4.167 0.615,0.198 10 false CAN- 4.354,1.719 4.969,1.917 0.615,0.198 10 false BATT 4.354,3.979 4.969,4.177 0.615,0.198 10 false GND 3.792,2.469 4.406,2.667 0.615,0.198 10 false s8 4.188,2.104 4.344,2.302 0.156,0.198 10 false 4 4.188,1.583 4.344,1.781 0.156,0.198 10 false 1 5.333,1.563 5.49,1.76 0.156,0.198 10 false 2 5.333,3.792 5.49,3.99 0.156,0.198 10 false 3 5.323,2.042 5.479,2.24 0.156,0.198 10 false 3 5.333,3.292 5.49,3.49 0.156,0.198 10 false 2 4.198,3.854 4.354,4.052 0.156,0.198 10 false 4 4.188,3.354 4.344,3.552 0.156,0.198 10 false 5 4.177,0.542 4.333,0.74 0.156,0.198 10 false 4 4.177,0.156 4.333,0.354 0.156,0.198 10 false 5 5.354,0.073 5.51,0.271 0.156,0.198 10 false 2 5.354,0.521 5.51,0.719 0.156,0.198 10 false 3 2.604,5.521 4.292,5.75 1.688,0.229 10 false NOX PM 4.563,6.771 4.719,6.969 0.156,0.198 10 false 6 1.99,1.125 3.063,1.323 1.073,0.198 10 false NOX FR 4.531,6.948 4.958,7.125 0.427,0.177 10 false 1V 5.813,3.292 6.073,3.5 0.26,0.208 10 false 27 5.802,3.802 6.063,4.01 0.26,0.208 10 false 35 6.031,3.969 6.646,4.167 0.615,0.198 10 false CAND 6.021,3.479 6.635,3.677 0.615,0.198 10 false CANU 6.042,7.323 6.656,7.521 0.615,0.198 10 false MREL 6.24,7.646 6.854,7.844 0.615,0.198 10 false G184 6.271,7.802 6.885,8 0.615,0.198 10 false ECM 5.771,7.167 6.031,7.375 0.26,0.208 10 false 14 3.396,7.656 4.781,7.844 1.385,0.188 10 false EFI MAIN NO. 1 2.073,7.125 3.458,7.313 1.385,0.188 10 false EFI MAIN NO. 1 1.406,6.958 1.719,7.156 0.313,0.198 10 false 1S 4.521,7.313 4.833,7.51 0.313,0.198 10 false 1V 4.573,7.146 4.729,7.344 0.156,0.198 10 false 7 2.385,7.969 5.229,8.219 2.844,0.25 10 false No.1 Integration Relay 5.229,8.229 7.083,8.406 1.854,0.177 10 false : CAN Communication Line 0.573,7.115 1.188,7.313 0.615,0.198 10 false 70A FL 1.448,6.74 1.625,6.938 0.177,0.198 10 false 1 0.542,8.052 1.156,8.25 0.615,0.198 10 false Battery 4.354,3.458 4.969,3.656 0.615,0.198 10 false BATT 5.063,5.708 5.667,6.042 0.604,0.333 10 false EFI MAIN NO. 3 2,6.51 3.688,6.74 1.688,0.229 10 false NOX PM 0.302,1.75 1.333,2.708 1.031,0.958 10 false *: w/ Particulate Matter Sensor 2.542,3.615 3.615,3.813 1.073,0.198 10 false NOX RR PM 2.188,4.438 2.5,4.635 0.313,0.198 10 false 1W 1.781,4.438 2.094,4.635 0.313,0.198 10 false 1W 2.344,4.635 2.698,4.833 0.354,0.198 10 false 11 1.688,4.635 1.979,4.875 0.292,0.24 10 false 10 2.938,5.115 3.25,5.313 0.313,0.198 10 false 1W 3.01,4.927 3.167,5.125 0.156,0.198 10 false 8 2.938,6.094 3.25,6.292 0.313,0.198 10 false 1W 3.01,5.906 3.167,6.104 0.156,0.198 10 false 4

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After the engine switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

According to the display on the GTS, select "Health Check".


d.

Check for currently output system DTCs.

Result:
Result Proceed to
DTC U02A387* is output A
DTC U029D87 is output B
DTC U029E87 is output C
2 or more of the following DTCs are simultaneously output: U02A387*, U029D87 or U029E87 D


HINT:

*: w/ Particulate matter sensor




A

2.CHECK PARTICULATE MATTER SENSOR

B

3.CHECK NO. 1 NITROGEN OXIDES SENSOR

C

4.CHECK NO. 2 NITROGEN OXIDES SENSOR

D

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
2.CHECK PARTICULATE MATTER SENSOR
a.

Disconnect the particulate matter sensor connector.


b.

Turn the engine switch on (IG).


c.
A426728C08
1.469,0.198 1.948,0.531 0.479,0.333 1.125,1.771 1.365,1.271 true 2.573,1.833 2.177,1.271 true 1.573,1.813 1.677,1.302 true 2.104,1.833 1.906,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.625,0.292 1.938,0.49 0.313,0.198 10 false s8 2.573,1.833 3.031,2.031 0.458,0.198 10 false GND 0.771,1.833 1.313,2.031 0.542,0.198 10 false BATT 1.417,1.833 1.958,2.031 0.542,0.198 10 false CAN+ 1.99,1.833 2.531,2.031 0.542,0.198 10 false CAN-
*a Front view of wire harness connector
(to Particulate Matter Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
s8-1 (BATT) - s8-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s8-2 (CAN+) - s8-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
s8-2 (CAN+) or s8-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
s8-2 (CAN+) or s8-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
s8-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C91
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.552,0.292 2.125,0.51 0.573,0.219 10 false C181 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C181-5 (BATT) - C181-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C181-2 (CAN+) - C181-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
C181-2 (CAN+) or C181-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
C181-2 (CAN+) or C181-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
C181-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the No. 2 nitrogen oxides sensor connector.


b.

Turn the engine switch on (IG).


c.
A383897C92
1.469,0.198 1.948,0.531 0.479,0.333 1.25,1.792 1.448,1.271 true 2.479,1.76 2.219,1.271 true 2.167,1.771 1.948,1.281 true 1.573,1.76 1.719,1.281 true 0.188,0.135 0.5,0.333 0.313,0.198 10 false *a 1.646,0.292 2.219,0.51 0.573,0.219 10 false s6 2.083,1.781 2.542,1.979 0.458,0.198 10 false GND 2.458,1.781 3,1.979 0.542,0.198 10 false BATT 1.313,1.792 1.854,1.99 0.542,0.198 10 false CAN- 0.896,1.781 1.438,1.979 0.542,0.198 10 false CAN+
*a Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
s6-5 (BATT) - s6-4 (GND) Engine switch on (IG) 11 to 14 V



d.

Turn the engine switch off.


e.

Disconnect the cable from the negative (-) battery terminal.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
s6-2 (CAN+) - s6-3 (CAN-) Cable disconnected from negative (-) battery terminal 54 to 69 Ω
s6-2 (CAN+) or s6-3 (CAN-) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
s6-2 (CAN+) or s6-3 (CAN-) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
s6-4 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (POWER SOURCE OF SENSOR)
A449209C08
1.448,0.104 1.948,0.385 0.5,0.281 2.219,0.104 2.719,0.385 0.5,0.281 4.813,0.104 5.313,0.385 0.5,0.281 1.781,1.448 2.198,1.031 true 4.333,1.458 4.75,1.042 true 2.719,1.458 2.458,1.052 true 5.656,1.448 5.396,1.042 true 1.542,0.167 2.073,0.49 0.531,0.323 10 false C181 2.406,0.156 2.833,0.458 0.427,0.302 10 false s6 4.979,0.156 5.313,0.479 0.333,0.323 10 false s8 1.99,0.156 2.323,0.479 0.333,0.323 10 false *a 5.354,0.156 5.688,0.479 0.333,0.323 10 false *c 2.771,0.177 3.104,0.5 0.333,0.323 10 false *b 2.635,1.5 3.125,1.729 0.49,0.229 10 false BATT 4.135,1.5 4.625,1.688 0.49,0.188 10 false BATT 1.542,1.5 1.99,1.698 0.448,0.198 10 false GND 5.604,1.5 6.094,1.74 0.49,0.24 10 false GND
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)
*c Front view of wire harness connector
(to Particulate Matter Sensor)
- -


a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Disconnect the No. 2 nitrogen oxides sensor connector.


c.

Disconnect the particulate matter sensor connector*.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C181-5 (BATT) - C181-4 (GND) Engine switch on (IG) 11 to 14 V
s6-5 (BATT) - s6-4 (GND) Engine switch on (IG) 11 to 14 V
s8-1 (BATT) - s8-4 (GND)* Engine switch on (IG) 11 to 14 V


HINT:

*: w/ Particulate matter sensor



e.

Reconnect the particulate matter sensor connector*.


f.

Reconnect the No. 2 nitrogen oxides sensor connector.


g.

Reconnect the No. 1 nitrogen oxides sensor connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM

NG

10.CHECK HARNESS AND CONNECTOR (SENSOR CONNECTOR - BODY GROUND)
6.CHECK ECM
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.
A449464C10
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.833,0.479 2.292,0.677 0.458,0.198 10 false G184 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G184-27 (CANU) or G184-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G184-27 (CANU) or G184-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Result Proceed to
OK A
NG (w/ Particulate matter sensor) B
NG (w/o Particulate matter sensor) C



A

B

7.CHECK PARTICULATE MATTER SENSOR

C

8.CHECK NO. 1 NITROGEN OXIDES SENSOR
7.CHECK PARTICULATE MATTER SENSOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Disconnect the particulate matter sensor connector.


d.
A449464C11
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.833,0.479 2.292,0.677 0.458,0.198 10 false G184 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G184-27 (CANU) or G184-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G184-27 (CANU) or G184-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

8.CHECK NO. 1 NITROGEN OXIDES SENSOR
8.CHECK NO. 1 NITROGEN OXIDES SENSOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Disconnect the No. 1 nitorogen oxides sensor connector.


d.
A449464C12
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false G184 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G184-27 (CANU) or G184-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G184-27 (CANU) or G184-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

9.CHECK NO. 2 NITROGEN OXIDES SENSOR
9.CHECK NO. 2 NITROGEN OXIDES SENSOR
a.

Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the ECM connector.


c.

Disconnect the No. 2 nitorogen oxides sensor connector.


d.
A449464C13
1.719,0.396 2.25,0.729 0.531,0.333 1.125,2.344 1.667,2.094 true 1.365,2.688 1.656,2.177 true 1.854,0.479 2.313,0.677 0.458,0.198 10 false G184 0.156,0.125 0.615,0.323 0.458,0.198 10 false *a 0.417,2.333 1.26,2.563 0.844,0.229 10 false 27 (CANU) 0.708,2.698 1.552,2.927 0.844,0.229 10 false 35 (CAND)
*a Rear view of wire harness connector
(to ECM Connector)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-27 (CANU) - G184-35 (CAND) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
G184-27 (CANU) or G184-35 (CAND) - Other power supply terminals Cable disconnected from negative (-) battery terminal 6 kΩ or higher
G184-27 (CANU) or G184-35 (CAND) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK HARNESS AND CONNECTOR (SENSOR CONNECTOR - BODY GROUND)
A449209C09
1.448,0.104 1.948,0.385 0.5,0.281 2.219,0.104 2.719,0.385 0.5,0.281 4.813,0.104 5.313,0.385 0.5,0.281 1.781,1.448 2.198,1.031 true 5.656,1.448 5.396,1.042 true 1.542,0.167 1.969,0.521 0.427,0.354 10 false C181 2.406,0.167 2.938,0.51 0.531,0.344 10 false s6 4.979,0.156 5.313,0.479 0.333,0.323 10 false s8 1.99,0.156 2.323,0.479 0.333,0.323 10 false *a 5.354,0.156 5.688,0.479 0.333,0.323 10 false *c 2.771,0.177 3.104,0.5 0.333,0.323 10 false *b 1.542,1.5 1.99,1.698 0.448,0.198 10 false GND 5.604,1.5 6.094,1.74 0.49,0.24 10 false GND
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)
*c Front view of wire harness connector
(to Particulate Matter Sensor)
- -


a.

Disconnect the No. 1 nitrogen oxides sensor connector.


b.

Disconnect the No. 2 nitrogen oxides sensor connector.


c.

Disconnect the particulate matter sensor connector*.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C181-4 (GND) - Body ground Always Below 1 Ω
s6-4 (GND) - Body ground Always Below 1 Ω
s8-4 (GND) - Body ground* Always Below 1 Ω


HINT:

*: w/ Particulate matter sensor



Result:
Proceed to
OK
NG



OK

11.INSPECT NO. 1 INTEGRATION RELAY (NOX PM RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.INSPECT NO. 1 INTEGRATION RELAY (NOX PM RELAY)
a.

Inspect the No. 1 integration relay (NOX PM relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

12.CHECK HARNESS AND CONNECTOR (NOX PM RELAY - NO. 1 NITROGEN OXIDES SENSOR, NO. 2 NITROGEN OXIDES SENSOR, PARTICULATE MATTER SENSOR)

NG

REPLACE NOX PM RELAY

12.CHECK HARNESS AND CONNECTOR (NOX PM RELAY - NO. 1 NITROGEN OXIDES SENSOR, NO. 2 NITROGEN OXIDES SENSOR, PARTICULATE MATTER SENSOR)
A449209C13
1.448,0.104 1.948,0.385 0.5,0.281 2.219,0.104 2.719,0.385 0.5,0.281 4.813,0.104 5.313,0.385 0.5,0.281 1.781,1.448 2.198,1.031 true 5.656,1.448 5.396,1.042 true 1.542,0.167 1.969,0.521 0.427,0.354 10 false C181 2.406,0.167 2.938,0.51 0.531,0.344 10 false s6 4.979,0.156 5.313,0.479 0.333,0.323 10 false s8 1.99,0.156 2.323,0.479 0.333,0.323 10 false *a 5.354,0.156 5.688,0.479 0.333,0.323 10 false *c 2.771,0.177 3.104,0.5 0.333,0.323 10 false *b 1.542,1.5 1.99,1.698 0.448,0.198 10 false GND 5.604,1.5 6.094,1.74 0.49,0.24 10 false GND
*a Front view of wire harness connector
(to No. 1 Nitrogen Oxides Sensor)
*b Front view of wire harness connector
(to No. 2 Nitrogen Oxides Sensor)
*c Front view of wire harness connector
(to Particulate Matter Sensor)
- -


a.

Remove the No. 1 integration relay.


b.

Disconnect the No. 1 nitorogen oxides sensor connector.


c.

Disconnect the No. 2 nitorogen oxides sensor connector.


d.

Disconnect the particulate matter sensor connector*.


e.

Measure the resistance according to the value(s) in the table below.


Standard Resistance:
Tester Connection Condition Specified Condition
1W-11 - C181-5 (BATT) Always Below 1 Ω
1W-11 - s6-5 (BATT) Always Below 1 Ω
1W-10 - s8-1 (BATT)* Always Below 1 Ω
1W-11 - C181-5 (BATT) - Body ground and other terminals Always 10 kΩ or higher
1W-11 - s6-5 (BATT) - Body ground and other terminals Always 10 kΩ or higher
1W-10 - s8-1 (BATT) - Body ground and other terminals* Always 10 kΩ or higher


HINT:

*: w/ Particulate matter sensor


Result:
Proceed to
OK
NG



OK

13.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CHECK TERMINAL VOLTAGE (POWER SOURCE OF NO. 1 INTEGRATION RELAY)
A476319C01
0.51,1.052 0.927,1.344 0.417,0.292 0.594,1.135 0.906,1.333 0.313,0.198 10 false 1S 0.073,0.104 0.385,0.302 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to No. 1 Integration Relay)


a.

Remove the No. 1 integration relay.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
1S-1 - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

14.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK HARNESS AND CONNECTOR (NO. 1 INTEGRATION RELAY - BODY GROUND)
a.

Remove the No. 1 integration relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1W-4 - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

15.CHECK HARNESS AND CONNECTOR

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK HARNESS AND CONNECTOR
a.

Remove the No. 1 integration relay.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1V-6 - 1W-8 Always Below 1 Ω
1V-6 or 1W-8 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

16.INSPECT NO. 1 INTEGRATION RELAY (NOX PM RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

16.INSPECT NO. 1 INTEGRATION RELAY (NOX PM RELAY)
a.

Inspect the No. 1 integration relay (NOX PM relay).

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/ Urea SCR System)>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

NG

REPLACE NO. 1 INTEGRATION RELAY (NOX PM RELAY)