Home › Vehicle Interior › HEATING / AIR CONDITIONING › COMPRESSOR (for 1GD-FTV) › from 2020.08
RM27T0E _58 Vehicle Interior _053739 HEATING / AIR CONDITIONING _0261204 COMPRESSOR(for 1GD-FTV) A

HEATING / AIR CONDITIONING  COMPRESSOR(for 1GD-FTV)  INSTALLATION  


PROCEDURE

Hide 1.ADJUST COMPRESSOR OIL

a.

When replacing the cooler compressor with a new one, gradually discharge the refrigerant gas from the service valve, and drain the following amount of oil from the new cooler compressor before installation.

Standard:

for Single Air Conditioning System:

(The amount of oil inside a new cooler compressor: 120 to 135 cc (4.1 to 4.6 fl. oz.)) - (The amount of oil remaining in the removed cooler compressor) = (The amount of oil to be removed when replacing the compressor)


Standard:

for Dual Air Conditioning System:

(The amount of oil inside a new cooler compressor: 180 to 195 cc (6.1 to 6.6 fl. oz.)) - (The amount of oil remaining in the removed cooler compressor) = (The amount of oil to be removed when replacing the compressor)


NOTICE:
·

When checking the compressor oil level, follow the A/C system precautions.

·

If a new cooler compressor is installed without removing some oil remaining in the pipes of the vehicle, the oil amount will be too large. This prevents heat exchange in the refrigerant cycle and causes refrigerant failure.

·

If the volume of oil remaining in the removed cooler compressor is too small, check for oil leakage.

·

for HFC-134a(R134a): Make sure to use ND-OIL 8 or equivalent compressor oil.

·

for HFO-1234yf(R1234yf): Make sure to use ND-OIL 12 or equivalent compressor oil.




Hide 88320 2.INSTALL COOLER COMPRESSOR ASSEMBLY

a.

Using an E8 "TORX" socket wrench, install the stud bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.
E321876E02
2.76,1.708 3.073,1.917 0.313,0.208 12 true (2) 2.688,0.698 3,0.906 0.313,0.208 12 true (1) 2.229,1.833 2.542,2.042 0.313,0.208 12 true (3) 1.885,0.219 2.198,0.427 0.313,0.208 12 true (4)

Temporarily install the cooler compressor assembly with the 3 bolts and nut.


c.

Tighten the 3 bolts and nut in the sequence shown in the illustration.

Torque:
24.5 N*m (250 kgf*cm, 18 ft.*lbf)


d.

Attach the clamp and connect the connector.


Hide 88712 3.CONNECT NO. 1 COOLER REFRIGERANT SUCTION HOSE

a.

Type A:

i.

Remove the attached vinyl tape from the No. 1 cooler refrigerant suction hose.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


iii.

Install the O-ring to the No. 1 cooler refrigerant suction hose.


iv.

Connect the No. 1 cooler refrigerant suction hose to the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



b.

Type B:

i.

Remove the attached vinyl tape from the No. 1 cooler refrigerant suction hose.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor Oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the No. 1 cooler refrigerant suction hose.


iv.

Connect the No. 1 cooler refrigerant suction hose to the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 88711 4.CONNECT NO. 1 COOLER REFRIGERANT DISCHARGE HOSE

a.

Type A:

i.

Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Refrigerant Compressor Oil
HFC-134a (R134a) ND-OIL 8 or equivalent
HFO-1234yf (R1234yf) ND-OIL 12 or equivalent


iii.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


iv.

Connect the No. 1 cooler refrigerant discharge hose to the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



b.

Type B:

i.

Remove the attached vinyl tape from the No. 1 cooler refrigerant discharge hose.


ii.

Sufficiently apply compressor oil to a new O-ring and the fitting surface of the cooler compressor assembly.

Compressor Oil:

ND-OIL 8 or equivalent



iii.

Install the O-ring to the No. 1 cooler refrigerant discharge hose.


iv.

Connect the No. 1 cooler refrigerant discharge hose to the cooler compressor with the bolt.

Torque:
9.8 N*m (100 kgf*cm, 87 in.*lbf)



Hide 82122 5.CONNECT NO. 2 ENGINE WIRE

a.

Attach the guide to connect the No. 2 engine wire.


b.

Install the bolt.

Torque:
12.8 N*m (131 kgf*cm, 9 ft.*lbf)


Hide 53292A 10.INSTALL UPPER RADIATOR SUPPORT SEAL