Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM (for Radio and Display Type) › from 2020.08
RM27T0E _56 Audio / Visual / Telematics _053720 AUDIO / VIDEO _0260969 AUDIO AND VISUAL SYSTEM(for Radio and Display Type) C

AUDIO / VIDEO  AUDIO AND VISUAL SYSTEM(for Radio and Display Type)  B15C0  GPS Antenna Connection Malfunction(short)  B15C1  GPS Antenna Connection Malfunction(break)  


DESCRIPTION

These DTCs are stored when a malfunction occurs in the navigation antenna assembly*1 or telephone antenna cord sub-assembly*2.

*1: w/o Heated Windshield Defroster System

*2: w/ Heated Windshield Defroster System


DTC No. Detection Item DTC Detection Condition Trouble Area
B15C0 GPS Antenna Connection Malfunction(short) Navigation antenna malfunction
w/o Heated Windshield Defroster System
·

Navigation antenna assembly

·

Radio and display receiver assembly


w/ Heated Windshield Defroster System and w/o Telematics Transceiver
·

Telephone antenna assembly

·

Telephone antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Harness or connector

·

Radio and display receiver assembly


w/ Heated Windshield Defroster System and w/ Telematics Transceiver
·

Telephone antenna assembly

·

Telephone antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna divider

·

Harness or connector

·

Radio and display receiver assembly


B15C1 GPS Antenna Connection Malfunction(break) Navigation antenna power source malfunction
w/o Heated Windshield Defroster System
·

Navigation antenna assembly

·

Radio and display receiver assembly


w/ Heated Windshield Defroster System and w/o Telematics Transceiver
·

Telephone antenna assembly

·

Telephone antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Harness or connector

·

Radio and display receiver assembly


w/ Heated Windshield Defroster System and w/ Telematics Transceiver
·

Telephone antenna assembly

·

Telephone antenna cord sub-assembly

·

No. 2 antenna cord sub-assembly

·

Antenna divider

·

Harness or connector

·

Radio and display receiver assembly



WIRING DIAGRAM

E353358E06
0.135,0.146 3.802,0.521 3.667,0.375 12 false w/o Heated Windshield Defroster System: 1.979,1.625 3.188,2.052 1.208,0.427 10 false Navigation Antenna Assembly 5.25,2.979 6.531,3.438 1.281,0.458 10 false Radio and Display Receiver Assembly

E353364E10
2.271,3.156 2.979,3.729 0.708,0.573 10 false Telephone Antenna Assembly 3.292,3.156 4.208,3.729 0.917,0.573 10 false Telephone Antenna Cord Sub-assembly 4.5,3.156 5.802,3.656 1.302,0.5 10 false No. 2 Antenna Cord Sub-assembly 2.625,6.583 3.875,7.156 1.25,0.573 10 false No. 2 Antenna Cord Sub-assembly 1.375,6.563 2.292,7.135 0.917,0.573 10 false Telephone Antenna Cord Sub-assembly 0.354,6.542 1.063,7.115 0.708,0.573 10 false Telephone Antenna Assembly 4.458,6.5 5.51,6.833 1.052,0.333 10 false Antenna Divider 3.073,1.802 3.229,2 0.156,0.198 10 false A 0.146,0.156 4.479,0.615 4.333,0.458 12 false w/ Heated Windshield Defroster System: 0.208,1.271 0.552,1.5 0.344,0.229 10 false *1 0.177,4.5 0.521,4.729 0.344,0.229 10 false *2 3.083,2.5 3.24,2.698 0.156,0.198 10 false A 1.188,5.188 1.344,5.385 0.156,0.198 10 false A 1.188,5.896 1.344,6.094 0.156,0.198 10 false A 4.292,1.813 4.448,2.01 0.156,0.198 10 false B 4.302,2.51 4.458,2.708 0.156,0.198 10 false B 2.385,5.188 2.542,5.385 0.156,0.198 10 false B 2.385,5.896 2.542,6.094 0.156,0.198 10 false B 5.5,1.792 5.771,2 0.271,0.208 10 false C 5.896,8.115 7.156,8.625 1.26,0.51 10 false Radio and Display Receiver Assembly 5.49,2.5 5.76,2.708 0.271,0.208 10 false C 0.104,8.125 2.156,8.365 2.052,0.24 10 false *1: w/o Telematics Transceiver 0.115,8.417 3.031,8.677 2.917,0.26 10 false *2: w/ Telematics Transceiver 3.604,5.188 3.875,5.396 0.271,0.208 10 false C 3.594,5.896 3.865,6.104 0.271,0.208 10 false C 3.021,5.188 3.635,5.385 0.615,0.198 10 false GPS1 6.115,5.198 6.469,5.406 0.354,0.208 10 false D 6.115,2.521 6.469,2.729 0.354,0.208 10 false D 6.125,1.813 6.479,2.021 0.354,0.208 10 false D 4.917,1.813 5.531,2.01 0.615,0.198 10 false GPS1 3.083,1.615 3.24,1.813 0.156,0.198 10 false 2 3.083,2.313 3.292,2.552 0.208,0.24 10 false 2a 4.292,1.615 4.448,1.813 0.156,0.198 10 false 2 4.271,2.302 4.49,2.51 0.219,0.208 10 false 2a 1.167,5.698 1.385,5.906 0.219,0.208 10 false 2a 1.198,5 1.354,5.198 0.156,0.198 10 false 2 2.385,4.99 2.542,5.188 0.156,0.198 10 false 2 2.365,5.688 2.583,5.896 0.219,0.208 10 false 2a 5.5,1.615 5.656,1.813 0.156,0.198 10 false 2 5.469,2.313 5.688,2.531 0.219,0.219 10 false 2a 6.083,2.302 6.302,2.521 0.219,0.219 10 false 1a 6.104,1.604 6.26,1.802 0.156,0.198 10 false 1 3.552,5.698 3.771,5.906 0.219,0.208 10 false 2a 3.594,4.99 3.75,5.188 0.156,0.198 10 false 2 4.26,5.104 4.417,5.302 0.156,0.198 10 false 6 4.219,5.781 4.438,5.99 0.219,0.208 10 false 6a 5.479,5.781 5.698,5.99 0.219,0.208 10 false 2a 5.469,5.094 5.688,5.302 0.219,0.208 10 false 2 6.094,5.698 6.313,5.906 0.219,0.208 10 false 1a 6.104,5 6.323,5.208 0.219,0.208 10 false 1 6.115,5.896 6.469,6.104 0.354,0.208 10 false D 4.458,6.313 4.813,6.521 0.354,0.208 10 false E

PROCEDURE

1.CHECK DTC

OK

NG

2.CHECK MODEL
2.CHECK MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
w/o Heated Windshield Defroster System A
w/ Heated Windshield Defroster System B



A

3.INSPECT NAVIGATION ANTENNA ASSEMBLY

B

4.CHECK MODEL
4.CHECK MODEL
a.

Choose the model to be inspected.

Result:
Result Proceed to
w/o Telematics Transceiver A
w/ Telematics Transceiver B




A

5.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY

B

9.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
5.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.
E321997C02
1.542,0.156 1.875,0.385 0.333,0.229 1.573,1.74 1.906,1.969 0.333,0.229 1.865,0.844 2.417,0.875 true 0.938,2.5 1.49,2.531 true 1.677,0.198 1.844,0.365 0.167,0.167 10 false A 1.698,1.792 1.865,1.958 0.167,0.167 10 false B 0.188,0.135 0.385,0.292 0.198,0.156 10 false *a 0.24,1.708 0.438,1.865 0.198,0.156 10 false *b 2.469,0.813 2.667,0.969 0.198,0.156 10 false 2a 0.74,2.406 0.938,2.563 0.198,0.156 10 false 2a
*a Front view of antenna connector
(to Telephone Antenna Assembly)
*b Front view of antenna connector
(to No. 2 Antenna Cord Sub-assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-2a - B-2a Always Below 1 Ω
A-2 or B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA CORD SUB-ASSEMBLY

6.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna cord sub-assembly.


b.

Disconnect the antenna connector from the wire harness.


c.
E446237C03
1.583,0.396 2.021,0.677 0.438,0.281 1.594,2.573 2.031,2.854 0.438,0.281 2.281,1.188 2.802,1.083 true 2.292,3.323 2.76,3.115 true 2.156,3.313 2.677,2.771 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.75,0.458 1.906,0.656 0.156,0.198 10 false B 2.865,1 3.063,1.198 0.198,0.198 10 false 2a 2.854,3.031 3.052,3.229 0.198,0.198 10 false 2a 0.177,2.563 0.49,2.76 0.313,0.198 10 false *b 1.781,2.635 1.938,2.833 0.156,0.198 10 false C 2.74,2.646 3.292,2.844 0.552,0.198 10 false GPS1
*a Front view of antenna connector
(to Telephone Antenna Cord Sub-assembly)
*b Front view of antenna connector
(to Wire Harness)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-2 (GPS1) Always Below 1 Ω
B-2a - C-2a Always Below 1 Ω
B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

7.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - RADIO AND DISPALY RECEIVER ASSEMBLY)

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

7.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - RADIO AND DISPALY RECEIVER ASSEMBLY)
a.
E446236C04
1.615,0.25 2.01,0.49 0.396,0.24 1.625,2.573 2.021,2.813 0.396,0.24 0.948,0.917 1.583,1.24 true 1.052,4.052 1.646,3.76 true 1.052,0.656 1.708,1.188 true 0.698,0.802 1.01,1 0.313,0.198 10 false 2a 0.125,0.115 0.438,0.313 0.313,0.198 12 false *a 0.156,2.26 0.469,2.458 0.313,0.198 12 false *b 0.823,3.958 1.135,4.156 0.313,0.198 10 false 1a 1.76,0.281 2.073,0.479 0.313,0.198 10 false C 1.781,2.604 2.094,2.802 0.313,0.198 10 false D 0.583,0.531 1.073,0.74 0.49,0.208 10 false GPS1
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Disconnect the No. 2 antenna cord sub-assembly connector.


b.

Disconnect the radio and display receiver assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 (GPS1) - D-1 Always Below 1 Ω
C-2a - D-1a Always Below 1 Ω
C-2 (GPS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

8.CHECK TELEPHONE ANTENNA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK TELEPHONE ANTENNA ASSEMBLY

OK

END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

NG

9.INSPECT TELEPHONE ANTENNA CORD SUB-ASSEMBLY
a.
E350951C19
1.646,0.271 2.042,0.552 0.396,0.281 1.677,2.563 2.073,2.844 0.396,0.281 1.26,1.313 1.677,1.271 true 1.063,3.417 1.594,3.583 true 0.115,0.094 0.427,0.292 0.313,0.198 10 false *a 1.083,1.219 1.396,1.417 0.313,0.198 10 false 2a 0.865,3.323 1.177,3.521 0.313,0.198 10 false 2a 1.792,0.333 1.948,0.531 0.156,0.198 10 false A 1.823,2.625 1.979,2.823 0.156,0.198 10 false B 0.208,2.656 0.521,2.854 0.313,0.198 10 false *b
*a Front view of wire harness connector
(to Telephone Antenna Assembly)
*b Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)


Disconnect the antenna connector from the telephone antenna assembly.


b.

Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A-2 - B-2 Always Below 1 Ω
A-2a - B-2a Always Below 1 Ω
A-2 or B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

10.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY

NG

REPLACE TELEPHONE ANTENNA CORD SUB-ASSEMBLY

10.INSPECT NO. 2 ANTENNA CORD SUB-ASSEMBLY
a.

Disconnect the antenna connector from the telephone antenna cord sub-assembly.


b.

Disconnect the antenna connector from the wire harness.


c.
E446237C04
1.583,0.396 2.021,0.677 0.438,0.281 1.573,2.521 2.01,2.802 0.438,0.281 2.281,1.188 2.802,1.083 true 2.292,3.323 2.76,3.115 true 2.156,3.333 2.552,2.896 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.75,0.458 1.906,0.656 0.156,0.198 10 false B 2.865,1 3.063,1.198 0.198,0.198 10 false 2a 2.854,3.031 3.052,3.229 0.198,0.198 10 false 2a 0.177,2.563 0.49,2.76 0.313,0.198 10 false *b 1.74,2.563 1.896,2.76 0.156,0.198 10 false C 2.625,2.802 3.063,2.979 0.438,0.177 10 false GPS1
*a Front view of antenna connector
(to Telephone Antenna Cord Sub-assembly)
*b Front view of antenna connector
(to Wire Harness)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
B-2 - C-2 (GPS1) Always Below 1 Ω
B-2a - C-2a Always Below 1 Ω
B-2 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - ANTENNA DIVIDER)

NG

REPLACE NO. 2 ANTENNA CORD SUB-ASSEMBLY

11.CHECK HARNESS AND CONNECTOR (NO. 2 ANTENNA CORD SUB-ASSEMBLY - ANTENNA DIVIDER)
a.
E446238C03
1.583,0.354 2.021,0.656 0.438,0.302 1.583,2.563 2.021,2.865 0.438,0.302 1.198,1.448 1.594,1.375 true 2.792,3.635 2.927,3.979 true 1.073,1.021 1.635,1.333 true 1.74,0.417 2.042,0.646 0.302,0.229 10 false C 0.146,0.094 0.458,0.292 0.313,0.198 10 false *a 1.74,2.635 2.083,2.854 0.344,0.219 10 false E 0.99,1.354 1.229,1.563 0.24,0.208 10 false 2a 2.938,3.979 3.177,4.188 0.24,0.208 10 false 6a 0.208,2.51 0.521,2.708 0.313,0.198 10 false *b 0.646,0.927 1.208,1.135 0.563,0.208 10 false GPS1
*a Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly)
*b Front view of wire harness connector
(to Antenna Divider)


Disconnect the No. 2 antenna cord sub-assembly connector.


b.

Disconnect the antenna divider connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C-2 (GPS1) - E-6 Always Below 1 Ω
C-2a - E-6a Always Below 1 Ω
C-2 (GPS1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

12.INSPECT ANTENNA DIVIDER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.INSPECT ANTENNA DIVIDER
a.

b.
E241596C16
1.125,1.417 0.979,1.76 0.979,1.76 0.781,1.76 true 1.979,1.406 1.833,1.75 1.833,1.75 1.635,1.75 true 0.573,1.677 1,1.854 0.427,0.177 10 false 6a 1.438,1.656 1.865,1.833 0.427,0.177 10 false 2a 0.177,0.135 0.49,0.333 0.313,0.198 10 false *a
*a Component without harness connected
(Antenna Divider)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
6 - 2 Always 10 kΩ or higher
2 - 2a Always 243 to 267 Ω
6 - 6a Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

13.CHECK HARNESS AND CONNECTOR (ANTENNA DIVIDER - RADIO AND DISPLAY RECEIVER ASSEMBLY)

NG

13.CHECK HARNESS AND CONNECTOR (ANTENNA DIVIDER - RADIO AND DISPLAY RECEIVER ASSEMBLY)
a.

Disconnect the antenna divider connector.


b.

Disconnect the radio and display receiver assembly connector.


c.
E353380C03
1.542,0.375 1.948,0.667 0.406,0.292 1.594,2.469 2,2.76 0.406,0.292 0.948,2.031 1.26,1.594 true 1.365,4.302 1.677,3.865 true 1.688,0.438 2.302,0.635 0.615,0.198 10 false E 1.729,2.531 2.344,2.729 0.615,0.198 10 false D 0.135,0.125 0.448,0.323 0.313,0.198 10 false *a 0.229,2.458 0.542,2.656 0.313,0.198 10 false *b 0.76,2 1.073,2.198 0.313,0.198 10 false 2a 1.167,4.25 1.479,4.448 0.313,0.198 10 false 1a
*a Front view of wire harness connector
(to Antenna Divider)
*b Front view of wire harness connector
(to Radio and Display Receiver Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E-2 - D-1 Always Below 1 Ω
E-2a - D-1a Always Below 1 Ω
E-2 or D-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

14.CHECK TELEPHONE ANTENNA ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

14.CHECK TELEPHONE ANTENNA ASSEMBLY

OK

END (TELEPHONE ANTENNA ASSEMBLY IS DEFECTIVE)

NG

15.CHECK ANTENNA DIVIDER
15.CHECK ANTENNA DIVIDER

OK

END (ANTENNA DIVIDER IS DEFECTIVE)

NG