Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _091546 STOP AND START _0437376 STOP AND START SYSTEM J

STOP AND START  STOP AND START SYSTEM  Engine Hood Courtesy Switch Circuit  


DESCRIPTION

The engine stop and start ECU detects whether the engine hood is open or closed based on a signal received from the engine hood courtesy switch built into the hood lock assembly.

·

The engine stop and start ECU prohibits starting of the engine by stop and start control and changes the mode to "stalled" if the engine hood is opened with the shift lever in D while the engine is stopped by stop and start control.


WIRING DIAGRAM

A348169E61
3.531,0.927 3.688,1.125 0.156,0.198 10 false 1 2.073,0.927 2.229,1.125 0.156,0.198 10 false 4 1.927,1.563 2.417,1.865 0.49,0.302 10 false A27 1.917,1.729 3.771,2.135 1.854,0.406 10 false Engine Hood Courtesy Switch (Hood Lock Assembly) 5.354,1.583 5.844,1.885 0.49,0.302 10 false G313 5.469,0.906 5.625,1.104 0.156,0.198 10 false 7 5.667,1.052 6.229,1.354 0.563,0.302 10 false BNT1 5.354,1.75 7.052,1.979 1.698,0.229 10 false Engine Stop and Start ECU 3.333,0.917 3.49,1.115 0.156,0.198 10 false + 2.26,0.927 2.417,1.125 0.156,0.198 10 false E

PROCEDURE

1.READ VALUE USING GTS (HOOD COURTESY SWITCH)
NOTICE:

Before performing this step, check that the engine hood can be opened by pulling the hood lock control cable.


a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Stop and Start / Data List / Hood Courtesy Switch.


e.

According to the display on the GTS, read the Data List.

OK:
Tester Display Condition Normal Condition
Hood Courtesy Switch Engine hood open OFF
Engine hood closed ON



Result:
Proceed to
OK
NG



OK

CHECK AND ADJUST HOOD LOCK ASSEMBLY FITTING (ADJUST HOOD)

NG

2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
2.INSPECT HOOD LOCK ASSEMBLY (ENGINE HOOD COURTESY SWITCH)
a.

Inspect the engine hood courtesy switch (hood lock assembly).

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENGINE HOOD COURTESY SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)

NG

3.CHECK HARNESS AND CONNECTOR (ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)
a.

Disconnect the engine hood courtesy switch (hood lock assembly) connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A27-4 (E) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - ENGINE HOOD COURTESY SWITCH (HOOD LOCK ASSEMBLY))
a.

Disconnect the engine stop and start ECU connector.


b.

Disconnect the engine hood courtesy switch (hood lock assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G313-7 (BNT1) - A27-1 (+) Always Below 1 Ω
G313-7 (BNT1) - Body ground Always 10 kΩ or higher
A27-1 (+) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

CHECK AND ADJUST HOOD LOCK ASSEMBLY FITTING (ADJUST HOOD)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR