Home › Engine / Hybrid System › CRUISE CONTROL › FRONT RADAR SENSOR SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0438240 FRONT RADAR SENSOR SYSTEM C

CRUISE CONTROL  FRONT RADAR SENSOR SYSTEM  U010487  Lost Communication with Cruise Control Module Missing Message  


DESCRIPTION

The millimeter wave radar sensor assembly communicates with the forward recognition camera via CAN communication.

If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the millimeter wave radar sensor assembly stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
U010487 Lost Communication with Cruise Control Module Missing Message
Detection condition:

Ignition switch ON


Malfunction status:

Communication malfunction with the forward recognition camera is detected


Malfunction duration:

10 seconds or more


·

Pre-collision system

·

Forward recognition camera

·

Millimeter wave radar sensor assembly

·

Harness or connector (Open)



HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


Pattern 1
DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly Forward Recognition Camera
Front Radar Sensor Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2
U010487 U023587 U023587 U023587 U023587

○: DTC is output

-: DTC is not output

○ ○ ○ ○ ○ Harness or connector (Open)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)

Pattern 2
DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Millimeter Wave Radar Sensor Assembly Forward Recognition Camera
Front Radar Sensor Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2
U010487 U023587 U023587 U023587 U023587

○: DTC is output

-: DTC is not output

○ - - - - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

WIRING DIAGRAM

E384731E65
0.333,1.74 2.375,2.25 2.042,0.51 10 false Forward Recognition Camera 5.323,1.865 6.76,2.229 1.438,0.365 10 false Millimeter Wave Radar Sensor Assembly 0.333,1.552 0.771,1.76 0.438,0.208 10 false W22 5.333,1.698 5.792,1.938 0.458,0.24 10 false A100 1.177,0.792 1.792,0.99 0.615,0.198 10 false CANH 1.188,1.469 1.802,1.667 0.615,0.198 10 false CANL 5.688,0.771 6.302,0.969 0.615,0.198 10 false CA1P 5.688,1.479 6.302,1.677 0.615,0.198 10 false CA1N 1.656,0.76 1.813,0.958 0.156,0.198 10 false 6 1.646,1.25 1.844,1.448 0.198,0.198 10 false 12 5.469,0.771 5.625,0.969 0.156,0.198 10 false 5 5.469,1.24 5.625,1.438 0.156,0.198 10 false 6

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly has been replaced with a new one, it is necessary to perform millimeter wave radar sensor assembly adjustment and front radar acceleration sensor calibration, and to clear the vehicle control history.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

If the forward recognition camera is replaced with a new one, it is necessary to perform forward recognition camera optical axis adjustment and clear the vehicle control history for each system.

HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)




PROCEDURE

1.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Pattern DTC Output Part Name
(Display on GTS)
Front Radar Sensor Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2
Pattern 1 U010487 U023587 U023587 U023587 U023587
Pattern 2 U010487 - - - -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

B

2.CHECK FORWARD RECOGNITION CAMERA
2.CHECK FORWARD RECOGNITION CAMERA
a.
C426618C17
0.313,0.979 0.688,1.26 0.375,0.281 0.844,1.688 0.958,1.688 0.958,1.688 1.427,1.229 true 1.01,1.917 1.125,1.917 1.125,1.917 1.604,1.24 true 0.344,1.042 0.75,1.26 0.406,0.219 10 false A100 0.448,1.594 1,1.813 0.552,0.219 10 false CA1P 0.604,1.833 1.156,2.052 0.552,0.219 10 false CA1N 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
A100-5 (CA1P) - A100-6 (CA1N) Ignition switch ON 1V/DIV., 100μs./DIV. Pulse generation



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPLACE FORWARD RECOGNITION CAMERA