Home › Vehicle Interior › PRE-COLLISION › PRE-COLLISION SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _091549 PRE-COLLISION _0438246 PRE-COLLISION SYSTEM C

PRE-COLLISION  PRE-COLLISION SYSTEM  U023587  Lost Communication with Cruise Control Front Distance Range Sensor Missing Message  


DESCRIPTION

The forward recognition camera communicates with the millimeter wave radar sensor assembly via CAN communication.

If a communication error is detected between the forward recognition camera and millimeter wave radar sensor assembly, the forward recognition camera stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area
U023587 Lost Communication with Cruise Control Front Distance Range Sensor Missing Message Once 3 seconds elapse after turning the ignition switch to ON, a communication malfunction between the millimeter wave radar sensor assembly continues for approximately 2 seconds or more.
·

Harness or connector

·

Forward recognition camera

·

Millimeter wave radar sensor assembly



HINT:

If the DTCs are output simultaneously, the inspection area can be narrowed down.


Pattern 1
DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Forward Recognition Camera Millimeter Wave Radar Sensor Assembly
Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2 Front Radar Sensor
U023587 U023587 U023587 U023587 U010487

○: DTC is output

-: DTC is not output

○ ○ ○ ○ ○ Harness or connector (Open or short)
Millimeter wave radar sensor assembly (Internal malfunction)
Forward recognition camera (Internal malfunction)

Pattern 2
DTC Output Part Name
(Display on GTS)
Suspected Area (Malfunction Status)
Forward Recognition Camera Millimeter Wave Radar Sensor Assembly
Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2 Front Radar Sensor
U023587 U023587 U023587 U023587 U010487

○: DTC is output

-: DTC is not output

○ ○ ○ ○ - Forward recognition camera (Internal malfunction)
Millimeter wave radar sensor assembly (Internal malfunction)

WIRING DIAGRAM

C424985E08
0.979,0.177 1.594,0.375 0.615,0.198 10 false CA1P 0.958,0.865 1.573,1.063 0.615,0.198 10 false CA1N 1.5,0.167 1.656,0.365 0.156,0.198 10 false 5 1.5,0.646 1.656,0.844 0.156,0.198 10 false 6 0.229,1.094 0.688,1.292 0.458,0.198 10 false A100 0.229,1.26 3.021,1.646 2.792,0.385 10 false Millimeter Wave Radar Sensor Assembly 5.271,0.146 5.427,0.344 0.156,0.198 10 false 6 5.208,0.615 5.427,0.865 0.219,0.25 10 false 12 5.51,0.167 6.125,0.365 0.615,0.198 10 false CANH 5.51,0.875 6.125,1.073 0.615,0.198 10 false CANL 4.958,1.094 5.417,1.292 0.458,0.198 10 false W22 4.958,1.271 6.885,1.604 1.927,0.333 10 false Forward Recognition Camera

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the millimeter wave radar sensor assembly, always replace it with a new one. If a millimeter wave radar sensor assembly which was installed to another vehicle is used, the information stored in the millimeter wave radar sensor assembly will not match the information from the vehicle and a DTC may be stored.

·

When the millimeter wave radar sensor assembly is replaced, be sure to adjust the millimeter wave radar sensor assembly beam axis, perform front radar G sensor learning, and clear the vehicle control history for each system.

Click hereEngine / Hybrid System>CRUISE CONTROL>MILLIMETER WAVE RADAR SENSOR>ADJUSTMENT

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to perform beam axis adjustment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera adjustment can be performed by using either One Time Recognition or Sequential Recognition.

One Time Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)

Sequential Recognition:

Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)


·

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART




PROCEDURE

1.CHECK FOR DTC
a.

Read each DTC and check the diagnosis pattern using the table below.

Pattern DTC Output Part Name
(Display on GTS)
Pre-Collision System Lane Control Forward Recognition Camera (Front Lighting Control) Radar Cruise2 Front Radar Sensor
Pattern 1 U023587 U023587 U023587 U023587 U010487
Pattern 2 U023587 U023587 U023587 U023587 -


Result:
Result Proceed to
Pattern 1 A
Pattern 2 B



A

2.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)

B

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
2.CHECK CAN MAIN WIRE (FORWARD RECOGNITION CAMERA)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C378826C48
0.573,0.979 0.948,1.26 0.375,0.281 2.146,1.104 2.51,0.927 true 2.135,1.427 2.542,1.615 true 0.615,1.052 0.958,1.25 0.344,0.198 10 false W22 2.573,0.854 3.125,1.073 0.552,0.219 10 false CANH 2.594,1.573 3.146,1.792 0.552,0.219 10 false CANL 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-6 (CANH) - W22-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
W22-6 (CANH) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
W22-12 (CANL) - Body ground
W22-6 (CANH) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
W22-12 (CANL) - +B



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

3.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
3.CHECK CAN MAIN WIRE (MILLIMETER WAVE RADAR SENSOR ASSEMBLY)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C426618C17
0.313,0.979 0.688,1.26 0.375,0.281 0.844,1.688 0.958,1.688 0.958,1.688 1.427,1.229 true 1.01,1.917 1.125,1.917 1.125,1.917 1.604,1.24 true 0.344,1.042 0.75,1.26 0.406,0.219 10 false A100 0.448,1.594 1,1.813 0.552,0.219 10 false CA1P 0.604,1.833 1.156,2.052 0.552,0.219 10 false CA1N 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


Disconnect the millimeter wave radar sensor assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A100-5 (CA1P) - A100-6 (CA1N) Cable disconnected from negative (-) battery terminal 108 to 132 Ω
A100-5 (CA1P) - Body ground Cable disconnected from negative (-) battery terminal 200 Ω or higher
A100-6 (CA1N) - Body ground
A100-5 (CA1P) - +B Cable disconnected from negative (-) battery terminal 6 kΩ or higher
A100-6 (CA1N) - +B



Result:
Proceed to
OK
NG



OK

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

NG

REPAIR OR REPLACE CAN BUS SUB LINE OR CONNECTOR

4.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY
a.
C378826C48
0.573,0.979 0.948,1.26 0.375,0.281 2.146,1.104 2.51,0.927 true 2.135,1.427 2.542,1.615 true 0.615,1.052 0.958,1.25 0.344,0.198 10 false W22 2.573,0.854 3.125,1.073 0.552,0.219 10 false CANH 2.594,1.573 3.146,1.792 0.552,0.219 10 false CANL 0.125,0.083 0.438,0.281 0.313,0.198 10 false *a
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


b.

Using an oscilloscope, check the waveform.

OK:
Tester Connection Switch Condition Tool Setting Specified Condition
W22-6 (CANH) - W22-12 (CANL) Ignition switch ON 1 V/DIV., 100 μs./DIV. Pulse generation



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY