The cruise control main switch outputs the dynamic cruise control on/off signal and various control signals to the ECM.
The ECM controls the dynamic cruise control system according to the signals received from the cruise control main switch.
Before replacing the ECM, refer to Service Bulletin.
The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION
Check vehicle condition.
| Result | Proceed to |
|---|---|
| for 1GD-FTV | A |
| for 1GR-FE, 2TR-FE | B |
A
B
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Cancel Switch | CANCEL switch status / ON or OFF | ON: CANCEL switch on
OFF: CANCEL switch off |
- |
| -SET Switch | -SET switch status / ON or OFF | ON: -SET switch on
OFF: -SET switch off |
- |
| +RES Switch | +RES switch status / ON or OFF | ON: +RES switch on
OFF: +RES switch off |
- |
| Cruise Main Switch Operation Condition | Cruise control main switch (ON-OFF) status / ON or OFF | ON: Cruise control main switch (ON-OFF) pushed
OFF: Cruise control main switch (ON-OFF) not pushed |
- |
The value of each Data List item changes according to the operation of the cruise control main switch.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Cancel Switch | CANCEL switch (ON-OFF) status / ON or OFF | ON: CANCEL switch on
OFF: CANCEL switch off |
- |
| -SET Switch | -SET switch status / ON or OFF | ON: -SET switch on
OFF: -SET switch off |
- |
| +RES Switch | +RES switch status / ON or OFF | ON: +RES switch on
OFF: +RES switch off |
- |
| Cruise Ready Main-CPU | Cruise control system standby condition / ON or OFF | ON: Cruise control main switch (ON-OFF) pushed
OFF: Cruise control main switch (ON-OFF) not pushed |
- |
The value of each Data List item changes according to the operation of the cruise control main switch.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereEngine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Remove the cruise control main switch.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL
Inspect the cruise control main switch.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Spiral Cable Sub-assembly) |
| *b | Front view of wire harness connector
(to Cruise Control Main Switch) |
Remove the cruise control switch wire.
Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| z7-3 (CCS) - A-3 | Always | Below 1 Ω |
| z7-4 (ECC) - A-1 | Always | Below 1 Ω |
| z7-3 (CCS) or A-3 - Body ground | Always | 10 kΩ or higher |
| z7-4 (ECC) or A-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL
Inspect the spiral cable sub-assembly.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION
| Result | Proceed to |
|---|---|
| OK (for 1GR-FE, 1GD-FTV) | A |
| OK (for 2TR-FE) | B |
| NG | C |
A
B
C
Disconnect the G208 spiral cable sub-assembly connector.
Disconnect the G56*1 or G185*2 ECM connector.
*1: for 1GR-FE
*2: for 1GD-FTV
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G208-1 (CCS) - G56-1 (CCS) | Always | Below 1 Ω |
| G208-2 (ECC) - Body ground | Always | Below 1 Ω |
| G208-1 (CCS) or G56-1 (CCS) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G208-1 (CCS) - G185-26 (CCS) | Always | Below 1 Ω |
| G208-2 (ECC) - Body ground | Always | Below 1 Ω |
| G208-1 (CCS) or G185-26 (CCS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
Disconnect the G208 spiral cable sub-assembly connector.
Disconnect the G181 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G208-1 (CCS) - G181-22 (CCS) | Always | Below 1 Ω |
| G208-2 (ECC) - G181-21 (ECCS) | Always | Below 1 Ω |
| G208-1 (CCS) or G181-22 (CCS) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG