Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM (for i-ART) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053696 CRUISE CONTROL _0438249 CRUISE CONTROL SYSTEM(for i-ART) J

CRUISE CONTROL  CRUISE CONTROL SYSTEM(for i-ART)  Cruise Control Switch Circuit  


DESCRIPTION

The cruise control main switch (ON-OFF button) is used to turn the cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUME), + (ACCEL), TAP-UP and CANCEL. The SET, TAP-DOWN and - (COAST) functions, and the RES (RESUME), TAP-UP and + (ACCEL) functions are operated with the same switch. The cruise control main switch is an automatic return type switch which turns on only while operating it in the direction of each arrow and turns off after releasing it. The internal contact points of the cruise control main switch turn on with switch operation. Then the ECM reads the voltage value that has been changed by the switch operation to control the SET, - (COAST), RES (RESUME), + (ACCEL), and CANCEL functions.

WIRING DIAGRAM

C448971E01
6.042,1.104 6.302,1.292 0.26,0.188 10 false 26 6.458,4.542 6.969,4.74 0.51,0.198 10 false G185 6.344,1.198 6.708,1.417 0.365,0.219 10 false CCS 6.479,4.719 6.948,4.906 0.469,0.188 10 false ECM 5.26,3 5.573,3.198 0.313,0.198 10 false 2 5.271,0.99 5.583,1.188 0.313,0.198 10 false 1 5.156,1.229 5.563,1.417 0.406,0.188 10 false G208 4.677,1.125 5.073,1.344 0.396,0.219 10 false CCS 4.646,3.104 5.01,3.302 0.365,0.198 10 false ECC 4.26,1 4.458,1.177 0.198,0.177 10 false 3 4.229,1.219 4.542,1.417 0.313,0.198 10 false z7 4.271,3.021 4.448,3.219 0.177,0.198 10 false 4 4.229,3.24 4.542,3.438 0.313,0.198 10 false z7 4.365,3.771 5.448,4.125 1.083,0.354 10 false Spiral Cable Sub-assembly 3.531,1.094 3.844,1.292 0.313,0.198 10 false 3 3.51,3.104 3.823,3.302 0.313,0.198 10 false 1 3.781,3.385 4.094,3.583 0.313,0.198 10 false * 2.885,2.198 3.51,2.406 0.625,0.208 10 false ON-OFF 2.094,2.208 2.635,2.406 0.542,0.198 10 false +RES 1.333,2.208 1.76,2.406 0.427,0.198 10 false -SET 0.552,2.198 1.219,2.438 0.667,0.24 10 false CANCEL 1.052,3.708 1.365,3.906 0.313,0.198 10 false A 1.01,3.875 2.917,4.125 1.906,0.25 10 false Cruise Control Main Switch 0.219,5.229 2.552,5.573 2.333,0.344 10 false *: Cruise Control Switch Wire 5.156,3.24 5.563,3.427 0.406,0.188 10 false G208 3.781,1.354 4.094,1.552 0.313,0.198 10 false *

CAUTION / NOTICE / HINT

NOTICE:
·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

Before replacing the ECM, refer to the Service Bulletin.



PROCEDURE

1.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

Read the Data List according to the display on the GTS.

Powertrain > Cruise Control > Data List
Tester Display Measurement Item / Range Normal Condition Diagnostic Note
Cancel Switch CANCEL switch status / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
-SET Switch -SET switch status / ON or OFF ON: -SET switch on
OFF: -SET switch off
-
+RES Switch +RES switch status / ON or OFF ON: +RES switch on
OFF: +RES switch off
-
Cruise Main Switch Operation Condition Cruise control main switch status / ON or OFF ON: Cruise control main switch on
OFF: Cruise control main switch off
-

OK:

When the cruise control main switch is operated, the display changes as shown above.



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.INSPECT CRUISE CONTROL MAIN SWITCH
2.INSPECT CRUISE CONTROL MAIN SWITCH
a.

Remove the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>REMOVAL


b.

Inspect the cruise control main switch.

Click hereEngine / Hybrid System>CRUISE CONTROL>CRUISE CONTROL MAIN SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT CRUISE CONTROL SWITCH WIRE

NG

3.INSPECT CRUISE CONTROL SWITCH WIRE
a.
E178683C46
0.292,0.729 0.729,1.042 0.438,0.313 0.24,2.385 0.677,2.698 0.438,0.313 1.656,1.542 1.281,1.094 true 0.656,1.542 1.073,1.125 true 0.146,0.313 0.458,0.51 0.313,0.198 10 false *a 0.24,1.969 0.552,2.167 0.313,0.198 10 false *b 0.417,2.458 0.573,2.656 0.156,0.198 10 false A 0.438,0.802 0.75,1 0.313,0.198 10 false z7 1.573,1.583 2.031,1.781 0.458,0.198 10 false ECC 0.49,1.552 0.948,1.75 0.458,0.198 10 false CCS
*a Front view of wire harness connector
(to Spiral Cable Sub-assembly)
*b Front view of wire harness connector
(to Cruise Control Main Switch)


Disconnect the spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
z7-3 (CCS) - A-3 Always Below 1 Ω
z7-4 (ECC) - A-1 Always Below 1 Ω
z7-3 (CCS) or A-3 - Body ground Always 10 kΩ or higher
z7-4 (ECC) or A-1 - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE CRUISE CONTROL SWITCH WIRE

4.INSPECT SPIRAL CABLE SUB-ASSEMBLY
a.

Remove the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>REMOVAL


b.

Inspect the spiral cable sub-assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>SPIRAL CABLE>INSPECTION


Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM AND BODY GROUND)
a.

Disconnect the G185 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G208-1 (CCS) - G185-26 (CCS) Always Below 1 Ω
G208-2 (ECC) - Body ground Always Below 1 Ω
G208-1 (CCS) or G185-26 (CCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR