Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › INTAKE SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053680 1GD-FTV INTAKE / EXHAUST _0260651 INTAKE SYSTEM G

1GD-FTV INTAKE / EXHAUST  INTAKE SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.INSPECT INTAKE SYSTEM

a.

Check that there is no air suction or leaks at the points shown in the illustration.

A463474C01
3.771,1.115 3.625,0.583 3.625,0.583 3.385,0.583 false 6.281,5.625 6.479,5.448 6.479,5.448 6.667,5.448 false 0.573,3.969 1.177,3.969 false 0.969,2.896 0.844,2.719 0.844,2.719 0.604,2.719 false 3.167,3.458 3.26,3.229 3.26,3.229 3.438,3.229 false 2.51,6.167 2.125,5.698 2.125,5.698 1.885,5.698 false 3.146,4.333 2.823,4.656 2.823,4.656 2.583,4.656 false 5.802,4.5 6.021,4.781 6.021,4.781 6.229,4.781 false 4.354,1.25 4.542,0.938 4.542,0.938 4.75,0.938 false 5.448,4.625 5.708,5.083 5.708,5.083 5.917,5.083 false 4.979,6.219 5.26,5.604 5.26,5.604 5.51,5.604 false 1.198,2.708 1.51,2.865 0.313,0.156 10 false *1 0.396,2.625 0.708,2.781 0.313,0.156 10 false *2 3.469,3.135 3.781,3.292 0.313,0.156 10 false *4 0.396,3.885 0.708,4.042 0.313,0.156 10 false *3 3.208,0.5 3.521,0.656 0.313,0.156 10 false *7 6.74,5.375 7.052,5.531 0.313,0.156 10 false *5 6.281,4.688 6.594,4.844 0.313,0.156 10 false *8 1.625,5.625 1.938,5.781 0.313,0.156 10 false *12 5.948,4.979 6.26,5.135 0.313,0.156 10 false *11 2.375,4.594 2.844,4.75 0.469,0.156 10 false *6 5.563,5.531 6.031,5.688 0.469,0.156 10 false *13 3.958,3.958 4.427,4.115 0.469,0.156 10 false *9 4.76,0.823 5.229,0.979 0.469,0.156 10 false *10 0.104,0.094 0.417,0.25 0.313,0.156 10 false *A
*A w/o EGR System - -
*1 Air Cleaner *2 Mass Air Flow Meter Sub-assembly
*3 Turbocharger Sub-assembly *4 PCV Pipe or Hose
*5 Vacuum Switching Valve (for Engine Mounting) *6 Exhaust Manifold
*7 Intercooler *8 Diesel Throttle Body
*9 Vacuum Pump *10 Intake Air Temperature Sensor
*11 Manifold Absolute Pressure Sensor *12 Front Engine Mounting Insulator RH
*13 Front Engine Mounting Insulator LH - -


A463475C01
3.771,1.115 3.625,0.583 3.625,0.583 3.385,0.583 false 6.281,5.625 6.479,5.448 6.479,5.448 6.667,5.448 false 0.573,3.969 1.177,3.969 false 0.969,2.896 0.844,2.719 0.844,2.719 0.604,2.719 false 3.167,3.458 3.26,3.229 3.26,3.229 3.438,3.229 false 2.51,6.167 2.125,5.698 2.125,5.698 1.885,5.698 false 3.146,4.333 2.823,4.656 2.823,4.656 2.583,4.656 false 5.802,4.5 6.021,4.781 6.021,4.781 6.229,4.781 false 4.354,1.25 4.542,0.938 4.542,0.938 4.75,0.938 false 5.448,4.625 5.708,5.083 5.708,5.083 5.917,5.083 false 4.979,6.219 5.26,5.604 5.26,5.604 5.51,5.604 false 4.792,3.604 5.01,3.302 5.01,3.302 5.25,3.302 false 1.198,2.708 1.51,2.865 0.313,0.156 10 false *1 0.396,2.625 0.708,2.781 0.313,0.156 10 false *2 3.469,3.135 3.781,3.292 0.313,0.156 10 false *4 0.396,3.885 0.708,4.042 0.313,0.156 10 false *3 3.208,0.5 3.521,0.656 0.313,0.156 10 false *7 6.74,5.375 7.052,5.531 0.313,0.156 10 false *5 6.281,4.688 6.594,4.844 0.313,0.156 10 false *8 5.302,3.198 5.615,3.354 0.313,0.156 10 false *12 5.948,4.979 6.26,5.135 0.313,0.156 10 false *11 2.375,4.594 2.844,4.75 0.469,0.156 10 false *6 5.563,5.531 6.031,5.688 0.469,0.156 10 false *13 3.958,3.958 4.427,4.115 0.469,0.156 10 false *9 4.76,0.823 5.229,0.979 0.469,0.156 10 false *10 1.625,5.646 2.094,5.802 0.469,0.156 10 false *14 0.104,0.094 0.417,0.25 0.313,0.156 10 false *A
*A w/ EGR System without EGR Cooler - -
*1 Air Cleaner *2 Mass Air Flow Meter Sub-assembly
*3 Turbocharger Sub-assembly *4 PCV Pipe or Hose
*5 Vacuum Switching Valve (for Engine Mounting) *6 Exhaust Manifold
*7 Intercooler *8 Diesel Throttle Body
*9 Vacuum Pump *10 Intake Air Temperature Sensor
*11 Manifold Absolute Pressure Sensor *12 Electric EGR Control Valve
*13 Front Engine Mounting Insulator LH *14 Front Engine Mounting Insulator RH


A463476C01
0.448,3.281 0.625,3.281 0.625,3.281 0.979,3.406 false 0.542,4.438 1.188,4.438 false 2.49,5.344 2.698,5.344 2.698,5.344 3.01,4.823 false 1.792,6.323 2,6.323 2,6.323 2.531,6.656 false 4.917,6.604 5.229,6.271 5.229,6.271 5.427,6.271 false 6.26,6.135 6.573,5.802 6.573,5.802 6.771,5.802 false 2.927,0.844 3.135,0.844 3.135,0.844 3.458,1.208 false 4.615,2.448 4.865,2.448 false 5.208,4.115 5.427,3.885 5.427,3.885 5.625,3.885 false 5.573,4.208 5.781,4.208 5.781,4.208 5.99,4.333 false 3.146,2.646 3.354,2.646 3.354,2.646 3.458,2.938 false 3.177,3.823 3.438,3.688 3.438,3.688 3.635,3.688 false 6.115,5.333 5.885,5.333 5.885,5.333 5.719,5.031 false 5.906,5.594 5.677,5.594 5.677,5.594 5.438,5.115 false 4.885,0.844 4.656,0.844 4.656,0.844 4.323,1.292 false 4.052,2.729 4.26,2.729 4.26,2.729 4.365,3.021 false 4.896,2.969 5.208,3.25 5.208,3.25 5.406,3.25 false 5.219,2.406 5.333,2.125 5.333,2.125 5.531,2.125 false 1.146,3.219 1.458,3.375 0.313,0.156 10 false *1 0.281,3.219 0.594,3.375 0.313,0.156 10 false *2 3.677,3.615 3.99,3.771 0.313,0.156 10 false *4 0.354,4.354 0.667,4.51 0.313,0.156 10 false *3 2.719,0.76 3.031,0.917 0.313,0.156 10 false *7 6.844,5.729 7.052,5.948 0.208,0.219 10 false *5 6.125,5.26 6.438,5.417 0.313,0.156 10 false *8 5.615,3.781 5.927,3.938 0.313,0.156 10 false *12 3.958,4.469 4.271,4.625 0.313,0.156 10 false *9 2.292,5.281 2.542,5.438 0.25,0.156 10 false *6 2.865,2.563 3.333,2.719 0.469,0.156 10 false *18 5.625,2.063 6.094,2.219 0.469,0.156 10 false *17 5.5,3.177 5.969,3.333 0.469,0.156 10 false *16 5.5,6.198 5.969,6.354 0.469,0.156 10 false *13 4.927,0.771 5.396,0.927 0.469,0.156 10 false *10 3.813,2.646 4.146,2.948 0.333,0.302 10 false *15 5.979,5.51 6.448,5.667 0.469,0.156 10 false *11 1.521,6.26 1.99,6.417 0.469,0.156 10 false *14 0.125,0.104 0.438,0.26 0.313,0.156 10 false *A
*A w/ EGR Cooler - -
*1 Air Cleaner *2 Mass Air Flow Meter Sub-assembly
*3 Turbocharger Sub-assembly *4 PCV Pipe or Hose
*5 Vacuum Switching Valve (for Engine Mounting) *6 Exhaust Manifold
*7 Intercooler *8 Diesel Throttle Body
*9 Vacuum Pump *10 Intake Air Temperature Sensor
*11 Manifold Absolute Pressure Sensor *12 Electric EGR Control Valve
*13 Front Engine Mounting Insulator LH *14 Front Engine Mounting Insulator RH
*15 EGR Cooler *16 No. 2 EGR Valve
*17 Vacuum Switching Valve (for EGR By-pass Valve) *18 No. 1 EGR Pipe Sub-assembly (EGR Pre-cooler)


A463477C01
0.427,3.281 0.604,3.281 0.604,3.281 0.969,3.385 false 0.542,4.438 1.188,4.438 false 2.49,5.344 2.698,5.344 2.698,5.344 3.01,4.823 false 1.792,6.323 2,6.323 2,6.323 2.531,6.656 false 4.917,6.604 5.229,6.271 5.229,6.271 5.427,6.271 false 6.26,6.135 6.573,5.802 6.573,5.802 6.771,5.802 false 5.542,2.542 5.542,2.292 false 2.927,0.844 3.135,0.844 3.135,0.844 3.458,1.208 false 3.458,0.333 3.667,0.333 3.667,0.333 3.99,0.698 false 4.615,2.448 4.865,2.448 false 5.208,4.115 5.427,3.885 5.427,3.885 5.625,3.885 false 5.573,4.208 5.781,4.208 5.781,4.208 5.99,4.333 false 3.146,2.646 3.354,2.646 3.354,2.646 3.458,2.938 false 3.177,3.823 3.438,3.688 3.438,3.688 3.635,3.688 false 6.115,5.333 5.885,5.333 5.885,5.333 5.719,5.031 false 5.906,5.594 5.677,5.594 5.677,5.594 5.438,5.115 false 2.865,1.323 2.552,0.99 2.552,0.99 2.333,0.99 false 4.052,2.729 4.26,2.729 4.26,2.729 4.365,3.021 false 4.896,2.969 5.208,3.25 5.208,3.25 5.406,3.25 false 5.208,2.5 5.156,2.99 5.156,2.99 5.354,2.99 false 1.198,3.229 1.51,3.385 0.313,0.156 10 false *1 0.25,3.219 0.563,3.375 0.313,0.156 10 false *2 3.677,3.615 3.99,3.771 0.313,0.156 10 false *4 0.354,4.354 0.667,4.51 0.313,0.156 10 false *3 2.719,0.76 3.031,0.917 0.313,0.156 10 false *7 3.885,2.625 4.198,2.781 0.313,0.156 10 false *5 6.125,5.26 6.438,5.417 0.313,0.156 10 false *8 5.615,3.781 5.927,3.938 0.313,0.156 10 false *12 5.948,5.5 6.26,5.656 0.313,0.156 10 false *9 5.417,3.146 5.667,3.302 0.25,0.156 10 false *6 2.229,5.271 2.698,5.427 0.469,0.156 10 false *18 3.917,4.469 4.385,4.625 0.469,0.156 10 false *19 1.521,6.25 1.99,6.406 0.469,0.156 10 false *17 5.479,6.177 5.948,6.333 0.469,0.156 10 false *16 2.073,0.927 2.542,1.083 0.469,0.156 10 false *13 5.406,2.917 5.875,3.073 0.469,0.156 10 false *10 6.802,5.74 7.135,6.042 0.333,0.302 10 false *15 5.365,4.115 5.833,4.271 0.469,0.156 10 false *11 2.885,2.594 3.354,2.75 0.469,0.156 10 false *14 4.885,0.708 5.354,0.865 0.469,0.156 10 false *20 5.438,2.573 5.906,2.729 0.469,0.156 10 false *21 3.198,0.25 3.667,0.406 0.469,0.156 10 false *22 0.125,0.104 0.438,0.26 0.313,0.156 10 false *A
*A w/ Urea SCR System - -
*1 Air Cleaner *2 Mass Air Flow Meter Sub-assembly
*3 Turbocharger Sub-assembly *4 PCV Pipe or Hose
*5 EGR Cooler *6 No. 2 EGR Valve
*7 Intercooler *8 Diesel Throttle Body
*9 Manifold Absolute Pressure Sensor *10 Vacuum Switching Valve (for EGR By-pass Valve)
*11 Intake Air Temperature Sensor *12 Electric EGR Control Valve
*13 Intake Air Temperature Sensor (for Intercooler) *14 No. 1 EGR Pipe Sub-assembly (EGR Pre-cooler)
*15 Vacuum Switching Valve (for Engine Mounting) *16 Front Engine Mounting Insulator LH
*17 Front Engine Mounting Insulator RH *18 Exhaust Manifold
*19 Vacuum Pump *20 Electric Water Pump Assembly
*21 Radiator Assembly (for Intercooler) *22 Coolant Temperature Sensor (for Intercooler)



Hide 2.CHECK INTAKE AIR CONTROL SYSTEM

a.

Check for leakage or clogging between the air cleaner housing and turbocharger inlet and between the turbocharger outlet and cylinder head.

Condition Operation
Clogged air cleaner Clean or replace element
Hoses collapsed or deformed Repair or replace
Leakage from connections Check each connection and repair
Cracks in components Check and repair or replace


Hide 3.CHECK EXHAUST SYSTEM

a.

Check for leakage or clogging between the cylinder head and turbocharger inlet and between the turbocharger outlet and exhaust pipe.

Condition Operation
Deformed components Repair or replace
Foreign material in passages Remove
Leakage from components Repair or replace
Cracks in components Check and repair or replace


Hide 4.CHECK BOOST PRESSURE

a.

Connect the GTS to the DLC3.


b.

Start the engine and turn the tester on.


c.

Warm up the engine.

HINT:

Be sure to perform the inspection when the engine coolant temperature is between 75 and 90°C (167 and 194°F).



d.

Enter the following menus: Powertrain / Engine / Data List / All Data.


e.

Take a snapshot of the Data List items with the GTS.

HINT:

The condition of the turbocharger sub-assembly can be determined by fully depressing the accelerator pedal while driving at 15 km/h (9 mph) in 2nd gear to accelerate the vehicle (obey all laws and regulations, and pay attention to driving conditions while driving the vehicle), and then comparing MAP with Target Booster Pressure at an engine speed of 3000 rpm.



f.

Compare Intake Manifold Absolute Pressure with Target Booster Pressure.

Standard:

Intake Manifold Absolute Pressure is within 25 kPa of Target Booster Pressure when accelerating with accelerator pedal fully depressed.


HINT:

If the driving inspection using the GTS above cannot be performed (e.g. due to road conditions), perform the following inspection.


i.

Warm up the engine.

HINT:

Be sure to perform the inspection when the engine coolant temperature is between 75 and 90°C (167 and 194°F).



ii.
A428340C01
0.802,0.594 1.083,0.344 1.083,0.344 1.25,0.344 true 0.625,1.792 0.823,1.792 0.823,1.792 1.188,1.302 true 1.24,3.01 1.385,2.76 1.385,2.76 1.552,2.76 true 2.052,1.781 2.292,2.063 2.292,2.063 2.458,2.063 true 1.469,4.281 1.667,4.5 1.667,4.5 1.833,4.5 true 1.646,3.604 1.948,3.875 1.948,3.875 2.115,3.875 true 0.052,0.063 0.365,0.219 0.313,0.156 10 true *A 0.073,2.344 0.385,2.5 0.313,0.156 10 false *B 1.323,0.281 1.635,0.438 0.313,0.156 10 true *1 2.521,1.979 2.833,2.135 0.313,0.156 10 true *2 0.448,1.688 0.76,1.844 0.313,0.156 10 true *a 1.604,2.688 1.917,2.844 0.313,0.156 10 true *1 1.865,4.385 2.177,4.542 0.313,0.156 10 true *2 2.958,0.167 3.333,0.385 0.375,0.219 10 true SST 3.01,2.583 3.406,2.74 0.396,0.156 10 true SST 2.156,3.781 2.469,3.938 0.313,0.156 10 true *a
*A w/o Urea SCR System
*B w/ Urea SCR System
*1 Manifold Absolute Pressure Sensor
*2 No. 1 Gas Filter
*a 3-Way Connector


Using a 3-way connector, connect SST (turbocharger pressure gauge) between the manifold absolute pressure sensor and No. 1 gas filter.

SST
09992-00242  


iii.

for Manual Transmission:

While depressing the clutch pedal, fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (4450 to 4750 rpm).

Standard pressure:

11.4 to 47.2 kPa (0.1 to 0.5 kgf/cm2, 1.7 to 6.8 psi)



iv.

for Automatic Transmission:

Move the shift lever to P or N, and then fully depress the accelerator pedal. Measure the boost pressure at maximum engine speed (4450 to 4750 rpm).

Standard pressure:

11.4 to 47.2 kPa (0.1 to 0.5 kgf/cm2, 1.7 to 6.8 psi)


If the pressure is below the standard, the following problems may be present.

·

The intake system or exhaust system has leakage or blockage.

·

The turbocharger sub-assembly is malfunctioning.

·

The electric EGR control valve does not close.

·

The diesel throttle body assembly does not open.

·

The vacuum hose connected to the manifold absolute pressure sensor is cracked or disconnected.

·

The mass air flow meter sub-assembly is malfunctioning.

·

A fuel injector assembly is malfunctioning.


If the pressure is higher than the standard, check the turbocharger sub-assembly and/or boost control components (manifold absolute pressure sensor, wire harness, etc.).



g.

w/ EGR System:

Chart showing the suspected trouble areas when the pressure is below the standard.

HINT:
·

○: If a problem listed in the leftmost column of the chart exists, or if the part in the leftmost column of the chart has a malfunction, the value of the Data List item in the uppermost row of the chart will meet the conditions shown in the row labeled "Value which represents a malfunction".

·

The values in the chart are applicable when the engine coolant temperature is between 75 and 90°C (167 and 194°F).

·

The values in the chart are for vehicles equipped with a manual transmission. For vehicles with an automatic transmission, use these values as a reference only as they may differ from the actual values.

·

The values in the chart are valid in an area with an atmospheric pressure higher than 95 kPa (1.0 kgf/cm2, 14 psi). Standard atmospheric pressure is 101 kPa (1.0 kgf/cm2, 15 psi). Atmospheric pressure decreases by 1 kPa (0.01 kgf/cm2, 0.1 psi) for every 100 m increase in altitude, and is also affected by the current weather conditions.

·

When the altitude increases, atmospheric pressure and Intake Manifold Absolute Pressure decrease.



Item Intake Manifold Absolute Pressure
(Absolute pressure inside intake manifold)
Mass Air Flow Sensor
(Intake air flow rate)
Accel Position Actual Throttle Position Actual EGR Valve Position No.1 EGR Close Learning Value Bank 1
(EGR valve fully closed position learning status)
Target Fuel Pressure (High) Injection Feedback Value #1
(to #4)
Values taken from an actual normal vehicle
*1
- 133 g/sec. 99.6% 0% 0% OK - -3 to +3 mm3/st
Values which represent a malfunction
*1
Intake Manifold Absolute Pressure is lower than Target Booster Pressure by 35 kPa or more Mass Air Flow Sensor is less than 105 g/sec Accel Position is less than 90%
*4
Actual Throttle Position is not within 5% of Target Throttle Position Actual EGR Valve Position is not within 5% of Target EGR Valve Position
*5
NG
(Determined after performing learning)
Fuel Pressure is below Target Common Rail Pressure by 10 MPa or more (Check while condition steady) Outside of above range
Turbocharger ○ ○ - - - - - -
EGR valve does not close or has problem with movement ○ ○ - - ○
(Problem with EGR valve movement)
*2
○
(EGR valve does not close)
*2
- -
Problem with diesel throttle movement ○
(Intake airflow decreases)
○ - ○ - - - -
Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists - ○ ○ - - - - -
Intake air system leakage or blockage ○ ○ - - - - - -
Exhaust gas leakage before turbocharger or blockage ○ ○ - - - - - -
Manifold absolute pressure sensor ○ ○ - - - - - -
Manifold absolute pressure sensor hose is disconnected ○ ○ - - - - - -
Mass air flow meter sub-assembly - ○ - - - - - -
Fuel system (injector, supply pump or common rail) ○ ○ - - - - ○
(Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck)
○
*3

HINT:
·

*1: These values are measured when the transmission is in 2nd gear, the accelerator pedal is fully depressed, the vehicle is accelerating, and the engine speed is 3000 rpm.

·

*2: DTC P040371 may be stored at this time. If the actual EGR valve position follows the target EGR valve position slowly, a feeling of hesitation may occur.

·

*3: If Injection Feedback Val # of a cylinder is not within -3 to +3 mm3/st, the corresponding cylinder has a malfunction (injector or compression). However, in some cases the cylinder may be malfunctioning even if the value is within -3 to +3 mm3/st.

·

*4: Accel Position is the accelerator opening angle (%) used for engine control. The value indicates 99.60% when the accelerator pedal is fully depressed. If the value indicates less than 90% when the accelerator pedal is fully depressed, the accelerator pedal position sensor circuit or the pedal itself is malfunctioning. When the MIL is illuminated, if Accel Position is below 70% even with the accelerator pedal fully depressed, it means the fail-safe is restricting the accelerator.

·

*5: Check that Actual EGR Valve Position No.1. is around 0% when the Target EGR position value indicates 0%. The EGR valve may be malfunctioning if the value is stuck or does not fluctuate smoothly. However, in some cases the EGR valve may be malfunctioning even if the Actual EGR Valve Position No.1. value is normal. Inspect the EGR valve for any defects (deposits, valve sticking, poor movement, etc.) if necessary.




h.

w/o EGR System:

Chart showing the suspected trouble areas when the boost pressure is lower than the standard.

HINT:
·

○: If a problem listed in the leftmost column of the chart exists, or if the part in the leftmost column of the chart has a malfunction, the value of the Data List item in the uppermost row of the chart will meet the conditions shown in the row labeled "Value which represents a malfunction".

·

The values in the chart are applicable when the engine coolant temperature is between 75 and 90°C (167 and 194°F).

·

The values in the chart are valid in an area with an absolute atmospheric pressure higher than 95 kPa. (Standard atmospheric pressure is 101 kPa. Atmospheric pressure decreases by 1 kPa for every 100 m increase in altitude, and is also affected by the current weather conditions.)

·

When the altitude increases, atmospheric pressure and Intake Manifold Absolute Pressure decrease.



Item Intake Manifold Absolute Pressure
(Absolute pressure inside intake manifold)
Mass Air Flow Sensor
(Intake air flow rate)
Accel Position Actual Throttle Position Target Fuel Pressure (High) Injection Feedback Value #1
(to #4)
Values taken from an actual normal vehicle
*1
- 133 g/sec 99.60% 0% - -3 to +3 mm3/st
Values which represent a malfunction
*1
Intake Manifold Absolute Pressure is lower than Target Booster Pressure by 35 kPa or more Mass Air Flow Sensor is less than 105 g/sec Accel Position is less than 90%
*2
Actual Throttle Position is not within 5% of Target Throttle Position Fuel Pressure is lower than Target Common Rail Pressure by 10 MPa or more (Check while the system is in a steady condition) Outside of the above range
Turbocharger ○ ○ - - - -
EGR valve does not close or has problem with movement ○ ○ - - - -
Problem with diesel throttle movement ○
(Intake airflow decreases)
○ - ○ - -
Accelerator pedal cannot be fully depressed or problem with accelerator pedal position sensor exists - ○ ○ - - -
Intake air system leakage or blockage ○ ○ - - - -
Exhaust gas leakage before turbocharger or blockage ○ ○ - - - -
Manifold absolute pressure sensor ○ ○ - - - -
Manifold absolute pressure sensor hose is disconnected ○ ○ - - - -
Mass air flow meter - ○ - - - -
Fuel system
(injector, supply pump or common rail)
○ ○ - - ○
(Fuel injector leakage, decrease in pressure discharge valve relief pressure or valve is stuck)
○
*3

HINT:
·

*1: These values are measured when the transmission is in 2nd gear, the accelerator pedal is fully depressed, the vehicle is accelerating, and the engine speed is 3000 rpm.

·

*2: Accel Position is the accelerator opening angle (%) used for engine control. The value indicates 99.60% when the accelerator pedal is fully depressed. If the value indicates less than 90% when the accelerator pedal is fully depressed, the accelerator pedal position sensor circuit or the pedal itself is malfunctioning. When the MIL is illuminated, if Accel Position is below 70% even with the accelerator pedal fully depressed, it means the fail-safe is restricting the accelerator.

·

*3: If Injection Feedback Val # of a cylinder is not within -3 to +3 mm3/st, the corresponding cylinder may have a malfunction (injector or compression). However, in some cases the cylinder may be malfunctioning even if the value is within -3 to +3 mm3/st because these values are injection volume correction values calculated by the ECM when the engine is idling and not correction values for the high engine load condition related to boost pressure control and engine output performance.




Hide 17201 5.INSPECT TURBOCHARGER SUB-ASSEMBLY (w/o DPF)

CAUTION:
·

Wear protective gloves to prevent injuries and burns when checking the turbocharger sub-assembly.

·

The engine compartment becomes hot when the engine is running.



a.

Remove the No. 1 exhaust manifold heat insulator (Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>REMOVAL).



c.

Make sure that the connector is properly connected.


d.
A456654C01
0.719,0.531 0.969,0.531 0.969,0.531 1.198,0.906 false 0.531,0.458 0.844,0.615 0.313,0.156 10 false *1 2.323,1.156 2.635,1.313 0.313,0.156 10 false *a 2.115,0.938 2.365,1.125 0.25,0.188 10 true *b 2.073,0.625 2.385,0.781 0.313,0.156 10 false *c 2.604,1.333 2.854,1.479 0.25,0.146 10 true *d 2.698,0.635 3.01,0.792 0.313,0.156 10 false *e
*1 DC Motor
*a Ignition switch ON
*b Ignition switch ON to engine idling
*c Turn the ignition switch off while the engine is idling
*b → *c → *d
*d Ignition switch off
*e 13.9 mm (0.547 in.)


Check the motor movement when turning the ignition switch to ON, when starting the engine, and then when turning the ignition switch off.

OK:

Vane actuation link and motor rod move smoothly when moving from position *b to position *c, and from position *c to position *d.


NOTICE:
A456656C01
0.948,4.281 1.188,4.281 1.188,4.281 1.563,4.031 true 0.844,4.198 1.052,4.396 0.208,0.198 10 true *1
*1 Lock Nut


Never loosen or tighten the lock nut of the fully closed stopper.


If the result is not as specified, check the ECM.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>TERMINALS OF ECM



f.

Install the No. 1 exhaust manifold heat insulator (Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/o DPF)>INSTALLATION).