Home › Engine / Hybrid System › 1GD-FTV (INTAKE / EXHAUST) › EXHAUST MANIFOLD W/ TURBOCHARGER › from 2020.08
RM27T0E _51 Engine / Hybrid System _053680 1GD-FTV INTAKE / EXHAUST _0260655 EXHAUST MANIFOLD W/ TURBOCHARGER D

1GD-FTV INTAKE / EXHAUST  EXHAUST MANIFOLD W/ TURBOCHARGER  SYSTEM DESCRIPTION  


This section should be used as a guide for troubleshooting when the turbocharger is suspected as the cause of a problem.

OUTLINE OF TURBOCHARGER FAILURE


a.

State of Turbocharger Failure Repair

It is well known that turbocharger malfunctions cause many symptoms, such as those shown below. However, the mechanisms resulting in these symptoms that indicate turbocharger malfunctions are not well understood. As a result, many unnecessary turbocharger replacements and other repairs are performed due to lack of knowledge about the turbocharger and turbocharger failure. Therefore, knowing the facts regarding turbocharger malfunctions is useful for making effective repairs and saving time.


b.

Turbocharger Failure Classification

Symptom Symptom Description See page
Noise Whistling noise Continuous high pitch noise proportional to engine speed
·

w/ Urea SCR System: (Click here)

·

w/o Urea SCR System: (Click here)


Whining noise Relatively low pitch noise compared to whistling noise
Oil leak External oil leak Oil leak on surface of turbocharger visible from outside of turbocharger
·

w/ Urea SCR System:(Click here)

·

w/o Urea SCR System:(Click here)


Internal oil leak Oil leak from inside of bearing housing to inside of either compressor housing or turbine housing through seal ring
White smoke Oil smoke Oil smoke is emitted from exhaust pipe
·

w/ Urea SCR System:(Click here)

·

w/o Urea SCR System:(Click here)


Unburned fuel smoke Unburned fuel smoke is emitted from exhaust pipe
Black smoke Black smoke is emitted from exhaust pipe
·

w/ Urea SCR System:(Click here)

·

w/o Urea SCR System:(Click here)


Lack of power or hesitation Vehicle does not reach target speed
·

w/ Urea SCR System:(Click here)

·

w/o Urea SCR System:(Click here)


Poor acceleration
Shock during acceleration
MIL turns on
DTC
P004512 Turbocharger/Supercharger Boost Control "A" Circuit Short to Battery
·

w/ Urea SCR System:(Click here)

·

w/o Urea SCR System:(Click here)


P004514 Turbocharger/Supercharger Boost Control "A" Circuit Short to Ground or Open
P004600 Turbocharger/Supercharger Boost Control "A" Circuit Range/Performance
P023400 Turbocharger/Supercharger "A" Overboost Condition
P029900 Turbocharger/Supercharger "A" Underboost Condition
P125100 Turbocharger Boost Control Malfunction
P256212 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit High Circuit Short to Battery
P256214 Turbocharger/Supercharger Boost Control Position Sensor "A" Circuit Low Circuit Short to Ground or Open
w/ Urea SCR System:
P226300
Turbocharger/Supercharger Boost System Performance

HINT:

This table shows only typical problems related to the turbocharger.




NOISE


Description
Probable Cause Probable Failed Component
Turbine shaft imbalance Turbocharger
Leakage from intake line Intake line
Gear noise
(Mistaken for turbocharger noise)
·

Balance shaft gear

·

Transmission gear

·

Vacuum pump gear



HINT:

It is easy to confirm whether the turbocharger is the cause of the noise or not, and confirming this before inspecting the turbocharger or removing it from the engine is an effective way to reduce troubleshooting time.


a.

Connect the GTS to the DLC3.


b.

Start the engine and warm it up.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Active Test / Activate the VN Turbo Open Bank 1.

Result Cause of Noise
The noise is reduced (or disappears) Turbocharger
The noise does not change Not turbocharger (other parts)

HINT:
·

w/ Urea SCR System:

For details regarding the troubleshooting of noise, refer to (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>Turbocharger Noise).

·

w/o Urea SCR System:

For details regarding the troubleshooting of noise, refer to (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>Turbocharger Noise).





OIL LEAK AND WHITE SMOKE


Description
Oil Leak Type Description Main Trouble Area
Internal oil leak
(White smoke)
·

Oil leak from bearing housing to either compressor housing (intake side) or turbine housing (exhaust side) through seal rings

·

This type of oil leak is not visible from outside of turbocharger

·

If oil leak occurs from turbine side seal, large amount of white smoke is emitted from exhaust side


·

Compressor side seal ring

·

Turbine side seal ring

·

Clogging of oil drain

·

Shaft breakage

·

Shaft or bearing seizure

·

Compressor impeller damage


External oil leak
·

Oil leak from inside of turbocharger to outside of turbocharger

·

Includes oil leaks visible from outside of turbocharger


·

O-ring

·

Oil pipe flange

·

Oil pipe union

·

Hose connection of intake pipe



A456661C01
1.917,0.177 2.146,0.177 2.146,0.177 2.615,0.604 true 4.885,1.417 5.708,0.552 5.708,0.552 5.938,0.552 true 1.135,0.406 1.365,0.406 1.365,0.406 2.729,2.135 true 1.115,3.25 1.354,3.25 1.354,3.25 2.469,2.448 true 1.219,2.313 1.708,2.313 true 2.688,0.146 2.917,0.146 2.917,0.146 3.792,1.292 true 4.667,2.375 5.438,3.552 5.438,3.552 5.667,3.552 true 3.521,3.781 3.521,3.531 3.521,3.531 3.365,2.813 true 2.844,4.76 2.802,3.854 true 4.26,2.198 5.865,2.198 true 3.604,2.281 4.219,0.302 4.219,0.302 4.448,0.302 true 5.917,2.115 6.229,2.313 0.313,0.198 10 false *2 2.469,1.156 2.656,1.354 0.188,0.198 10 false *a 4.521,0.219 4.833,0.417 0.313,0.198 10 false *6 0.938,0.333 1.25,0.531 0.313,0.198 10 false *2 1.719,0.115 2.031,0.313 0.313,0.198 10 false *1 1.031,2.25 1.344,2.448 0.313,0.198 10 false *3 0.927,3.177 1.24,3.375 0.313,0.198 10 false *4 2.469,0.063 2.781,0.26 0.313,0.198 10 false *5 6.01,0.479 6.323,0.677 0.313,0.198 10 false *9 3.458,3.833 3.771,4.031 0.313,0.198 10 false *7 2.802,4.813 3.115,5.01 0.313,0.198 10 false *8 5.75,3.479 6.063,3.677 0.313,0.198 10 false *10 0.646,4.135 0.865,4.323 0.219,0.188 10 true *a 4.448,4.125 4.656,4.313 0.208,0.188 10 true *b 4.833,1.323 5.01,1.5 0.177,0.177 8 false ● 3.76,1.198 3.938,1.375 0.177,0.177 8 false ● 4.615,2.25 4.792,2.427 0.177,0.177 8 false ● 1.708,2.229 1.885,2.406 0.177,0.177 8 false ● 3.563,2.198 3.74,2.375 0.177,0.177 8 false ● 2.448,2.323 2.625,2.5 0.177,0.177 8 false ● 3.313,2.677 3.49,2.854 0.177,0.177 8 false ● 2.583,0.51 2.76,0.688 0.177,0.177 8 false ● 2.771,3.75 2.948,3.927 0.177,0.177 8 false ●
*1 Compressor Housing *2 Seal Ring
*3 Compressor Inlet *4 Compressor Impeller
*5 Bearing Housing *6 Turbine Shaft
*7 Oil Drain (Outlet) *8 O-Ring
*9 Turbine Housing *10 Turbine Wheel
*a Internal oil leak to compressor housing *b Internal oil leak to turbine housing


HINT:
·

Above illustration is an example.

·

When there is an internal oil leak, white smoke is emitted from the exhaust pipe and oil is consumed excessively. However, the cause of white smoke or excessive oil consumption can vary. Therefore, do not assume that the turbocharger is the cause of the failure when there is white smoke emission or excessive oil consumption.

·

When there is an external oil leak, the sources of the oil leak are limited to the points listed in the table above. If oil leaks from a FIPG sealing part, replace the turbocharger. If oil leaks from an oil pipe flange or a hose connection, do not replace the turbocharger, but confirm and repair the flange or hose.

·

w/ Urea SCR System:

For details regarding the troubleshooting of oil leaks and white smoke, refer to (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>Turbocharger Oil Leak and White Smoke).

·

w/o Urea SCR System:

For details regarding the troubleshooting of oil leaks and white smoke, refer to (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>Turbocharger Oil Leak and White Smoke).




BLACK SMOKE


a.

Malfunctions are classified into 2 types as shown below.

Description
Malfunction Main Fault
Intake air volume shortage Insufficient mass air flow due to, for example, excessively low boost pressure, which results in fuel injection volume being relatively excessive with respect to mass air flow
Excessive injection volume Excessive injection volume or incorrect injection timing due to fuel system trouble


b.

Main Components Related to Black Smoke

Possible Faulty Component Main Fault
Turbocharger Abnormally low boost pressure
Intake system Leakage between turbocharger and intake manifold
Fuel system
·

Excessive fuel injection volume

·

Incorrect fuel injection timing


EGR valve Stuck or does not close completely
Diesel throttle Stuck or does not move smoothly

HINT:
·

w/ Urea SCR System:

The components listed above are only the main components. Not all the components potentially related to black smoke are listed. For details regarding the troubleshooting of black smoke, refer to (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>Black Smoke Emitted).

·

w/o Urea SCR System:

The components listed above are only the main components. Not all the components potentially related to black smoke are listed. For details regarding the troubleshooting of black smoke, refer to (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>Black Smoke Emitted).




c.

Relation between Turbocharger and Black Smoke

If the boost pressure is below normal due to a turbocharger failure, black smoke may occur due to a lack of mass air flow. However, abnormally low boost pressure can be caused by the failure of various components, such as intake lines, the EGR valve, etc. Therefore, do not assume that the turbocharger is the cause of abnormally low boost pressure, but check all the components possibly related to abnormally low boost pressure. Components related to abnormal boost pressure are shown in a chart listed in the On-vehicle Inspection for Intake System (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION). For simple and effective troubleshooting, refer to the chart before starting troubleshooting.



LACK OF POWER AND HESITATION


a.

Malfunctions are classified into 2 types as shown below.

Description
Malfunction Main Fault
Intake air volume shortage Insufficient mass air flow due to, for example, excessively low boost pressure, which results in fuel injection volume being restricted
Abnormal injection volume Abnormal injection volume or timing due to fuel system trouble


b.

Main Components Related to Lack of Power and Hesitation

Possible Faulty Component Main Fault
Turbocharger
·

Abnormal boost pressure

·

VN does not move smoothly


Intake system
·

Leakage between turbocharger and intake manifold

·

Clogging or blockage of intake line


Fuel system
·

Abnormal injection volume

·

Incorrect fuel injection timing


EGR valve Stuck or does not close completely
Diesel throttle Stuck or does not move smoothly
Exhaust system Clogging of exhaust line

HINT:
·

w/ Urea SCR System:

The components listed above are only the main components. Not all the components potentially related to lack of power and hesitation are listed. For details regarding the troubleshooting of lack of power and hesitation, refer to (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ Urea SCR System)>Lack of Power or Hesitation).

·

w/o Urea SCR System:

The components listed above are only the main components. Not all the components potentially related to lack of power and hesitation are listed. For details regarding the troubleshooting of lack of power and hesitation, refer to (See page Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>Lack of Power or Hesitation).




c.

Relation between Turbocharger and Abnormal Boost Pressure

If the boost pressure is below normal due to a turbocharger failure, lack of power could occur due to an intake air volume shortage. However, abnormal boost pressure can be caused by the failure of various components, such as intake lines, the EGR valve, etc. Therefore, do not assume that the turbocharger is the cause of abnormal boost pressure, but check all the components possibly related to abnormal boost pressure. Components related to abnormal boost pressure are shown in a chart listed in the On-vehicle Inspection for Intake System (See page Engine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>INTAKE SYSTEM>ON-VEHICLE INSPECTION). For simple and effective troubleshooting, refer to the chart before starting troubleshooting.



MIL TURNS ON


If a DTC related to a turbocharger malfunction is output, refer to the troubleshooting section for each DTC.



BRIEF OUTLINE OF TURBOCHARGER OPERATION AND CONSTRUCTION


a.

A turbocharger is a component used to supply a larger air volume to the cylinders by recovering exhaust gas energy using a turbine coaxially connected to a compressor.


b.

Principle of Turbocharging

Boost pressure is proportional to turbocharger speed, because the intake air is accelerated by centrifugal force generated by the rotation of the compressor and the increased kinetic energy, i.e. the velocity of the intake air, is converted to pressure energy by the diffuser located around the outlet of the compressor impeller. The compressor is driven by the turbine connected coaxially to the turbine shaft. The turbine is driven by exhaust gas energy. Therefore, when the turbocharger begins boosting the intake air, a larger air volume is supplied to the cylinders and more fuel can be injected. As a result, more exhaust energy is available and the turbocharger boost increases.

A456662C01
2.51,7.26 2.719,7.26 2.719,7.26 3.844,6.156 true 3.25,0.688 2.823,0.385 2.823,0.385 2.635,0.385 true 4.781,0.677 5.094,0.385 5.094,0.385 5.292,0.385 true 2.469,2.854 2.042,2.552 2.042,2.552 1.854,2.552 true 3.792,5.469 4.833,4.406 4.833,4.406 5.031,4.406 true 2.448,0.333 2.76,0.531 0.313,0.198 10 false *1 5.344,0.323 5.656,0.521 0.313,0.198 10 false *2 4.865,2.031 5.156,2.229 0.292,0.198 10 false *a 4,2.375 4.292,2.573 0.292,0.198 10 false *4 4,3.302 4.292,3.5 0.292,0.198 10 false *5 1.625,2.49 1.917,2.688 0.292,0.198 10 false *6 1.927,1.135 2.219,1.333 0.292,0.198 10 false *3 5.104,4.344 5.396,4.542 0.292,0.198 10 false *7 4,5.938 4.292,6.135 0.292,0.198 10 false *b 2.302,7.198 2.594,7.396 0.292,0.198 10 false *8 3.823,6.042 4.01,6.281 0.188,0.24 8 false ●
*1 Compressor *2 Turbine
*3 Air Cleaner *4 Exhaust Manifold
*5 Intake Manifold *6 Intercooler
*7 Diffuser *8 Compressor Impeller
*a See HINT below *b Intake air flow


HINT:
·

Above illustration is an example.

·

*a: If sufficient exhaust gas energy is not available, the turbocharger cannot generate the required boost pressure even when the turbocharger does not have a malfunction.

·

Considering the fact that the turbocharger is driven by exhaust gas energy, if sufficient exhaust gas is not available due to abnormal injection volume, etc., the required boost pressure will not be available even when the turbocharger does not have a malfunction. Therefore, when boost pressure is abnormally low, checking all the related components using the correct troubleshooting procedure is necessary for simple and effective repair.




c.

Boost Pressure Control

The amount of energy the turbine can obtain from the exhaust gas is proportional to the expansion ratio, which is defined as the ratio of the turbine inlet exhaust gas pressure to the pressure at the turbine outlet. To control boost pressure, a Variable Nozzle (VN) is used just upstream of the turbine wheel inlet, and controls the expansion ratio. If the VN is closed, the gap between neighboring vanes is narrowed and the turbine inlet exhaust gas pressure, and correspondingly the expansion ratio, increases. Therefore, when the VN is closed, the turbine receives more energy, and the turbine speed and boost pressure increase. If the VN is opened, the turbine inlet exhaust gas pressure decreases and the turbine speed and boost pressure decrease.

A211795C05
1.417,0.5 1.521,0.5 1.521,0.5 1.844,1.49 true 0.542,1.021 0.979,1.021 0.979,1.021 1.656,1.667 true 3.906,0.99 4.365,0.99 4.365,0.99 5.167,1.75 true 2.708,3.281 2.708,3.177 2.708,3.177 2.406,2.24 true 6.104,3.281 6.104,3.177 6.104,3.177 5.813,2.24 true 4.771,0.469 4.885,0.469 4.885,0.469 5.198,1.448 true 3.708,0.927 3.896,1.073 0.188,0.146 10 false *4 1.813,0.052 2,0.198 0.188,0.146 10 false *a 5.229,0.052 5.417,0.198 0.188,0.146 10 false *b 1.24,0.427 1.427,0.573 0.188,0.146 10 false *1 4.594,0.396 4.781,0.542 0.188,0.146 10 false *1 2.625,3.375 2.813,3.521 0.188,0.146 10 false *2 6.021,3.333 6.208,3.479 0.188,0.146 10 false *2 0.271,0.969 0.458,1.115 0.188,0.146 10 true *3 2.667,1.76 2.854,1.906 0.188,0.146 10 true *c 6.156,1.802 6.344,1.948 0.188,0.146 10 true *c
*1 VN (Variable Nozzle) *2 Turbine Wheel
*3 Narrow Gap *4 Wide Gap
*a VN Closed *b VN Opened
*c Exhaust Gas Flow - -


HINT:
·

Above illustration is an example.

·

If the VN is stuck open, the necessary boost pressure is not available. If the VN is stuck closed, overboost occurs.




d.

Mechanical Construction of Turbocharger

A456663C01
4.156,0.802 4.677,0.406 4.677,0.406 4.948,0.406 true 3.573,1.542 4.792,1.969 4.792,1.969 5.063,1.969 true 0.635,3.385 0.896,3.385 0.896,3.385 2.031,4.333 true 0.99,2.854 1.25,2.854 1.25,2.854 2.719,5.115 true 3.802,4.198 4.042,2.792 4.042,2.792 4.313,2.792 true 4.094,4.969 4.708,2.573 4.708,2.573 4.979,2.573 true 4.385,4.396 5.583,2.771 5.583,2.771 5.854,2.771 true 5,4.49 5.708,3.479 5.708,3.479 5.979,3.479 true 4.688,5.292 5.792,6.948 5.792,6.948 6.063,6.948 true 1.208,6.792 1.469,6.792 1.469,6.792 2.521,5.417 true 1.896,7.365 2.156,7.365 2.156,7.365 3.313,5.792 true 4.24,7.406 3.979,7.406 3.979,7.406 3.635,5.281 true 1.438,2.5 1.698,2.5 1.698,2.5 3.031,5.01 true 1.719,2.51 3.74,4.99 true 5.01,0.333 5.323,0.531 0.313,0.198 10 false *1 5.042,2.51 5.615,2.74 0.573,0.229 10 false *5 (*b) 4.365,2.719 4.677,2.917 0.313,0.198 10 false *3 5.135,1.885 5.448,2.083 0.313,0.198 10 false *2 6.135,6.865 6.448,7.063 0.313,0.198 10 false *7 4.302,7.344 4.615,7.542 0.313,0.198 10 false *4 1.646,7.281 1.958,7.479 0.313,0.198 10 false *13 0.958,6.719 1.271,6.917 0.313,0.198 10 false *11 0.375,3.313 0.688,3.51 0.313,0.198 10 false *10 0.573,2.781 1.125,2.979 0.552,0.198 10 false *9 (*b) 1.229,2.417 1.542,2.615 0.313,0.198 10 false *8 6.031,3.406 6.344,3.604 0.313,0.198 10 false *6 5.948,2.688 6.26,2.885 0.313,0.198 10 false *12 1.198,4.969 1.51,5.167 0.313,0.198 10 false *a 4.094,0.729 4.25,0.927 0.156,0.198 8 false ● 3.49,1.427 3.646,1.625 0.156,0.198 8 false ● 2.021,4.25 2.177,4.448 0.156,0.198 8 false ● 3.292,5.656 3.448,5.854 0.156,0.198 8 false ● 3.583,5.146 3.74,5.344 0.156,0.198 8 false ● 4.927,4.417 5.083,4.615 0.156,0.198 8 false ● 4.313,4.323 4.469,4.521 0.156,0.198 8 false ● 3.74,4.135 3.896,4.333 0.156,0.198 8 false ● 3.75,4.948 3.906,5.146 0.156,0.198 8 false ● 3,4.948 3.156,5.146 0.156,0.198 8 false ● 2.49,5.302 2.646,5.5 0.156,0.198 8 false ● 4.635,5.156 4.792,5.354 0.156,0.198 8 false ●
*1 VN Actuator (DC Motor) *2 VN Actuating Rod
*3 Bearing Housing *4 Turbine Shaft
*5 Turbine Side Seal Ring *6 Turbine Housing
*7 Turbine Wheel *8 Ball Bearing
*9 Compressor Side Seal Ring *10 Compressor Housing
*11 Compressor Impeller *12 VN (Variable Nozzle)
*13 Oil Drain - -
*a See HINT below *b See HINT below
V100135

Exhaust Gas Flow
V100136

Intake Air Flow


HINT:
·

Above illustration is an example.

·

*a: A certain amount of oil mist from PCV gas is contained in the intake air. Therefore, a certain amount of oil at the inlet of the compressor is normal, and is not an oil leak.

·

b: The seal rings are C-shaped rings just like piston rings, and have a gap. Therefore, complete sealing is impossible by the seal rings alone. The oil is sealed in with the aid of the boost pressure in the compressor housing, and the exhaust gas pressure in the turbine housing. These pressures prevent oil from exiting the bearing housing through the gap of the seal rings. Therefore, if the turbine shaft is inclined from the horizontal, oil may flow out through the gap of a seal ring. This should not be interpreted as an oil leak due to seal ring failure.