The main body ECU (multiplex network body ECU) controls the automatic high beam system based on signals received from the forward recognition camera.
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle. As a result, a DTC may be stored.
If the forward recognition camera has been replaced with a new one, be sure to perform Forward Recognition Camera Learning.
for sequential recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (SEQUENTIAL RECOGNITION)
for one time recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>ADJUSTMENT (ONE TIME RECOGNITION)
Check the operation of the automatic high beam indicator light.
Turn the ignition switch to ON.
Turn the light control switch to the Auto or Head position.
Turn the headlight dimmer switch to the High position.
Turn the auto high beam switch on.
Automatic high beam indicator light illuminate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST
| *1 | Forward Recognition Camera (Automatic High Beam Sensor) |
| *2 | Work Light or Equivalent |
| *a | 100 mm (3.94 in.) or less |
Shine a light on the automatic high beam sensor*.
*: If troubleshooting is being performed in a bright area, such as outside on a sunny day, it will not be necessary to perform this step.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Auto H Beam STS0 | Automatic high beam sensor state past 0 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
The Data List value displays "Daytime".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST
| *1 | Cardboard or Equivalent Object |
| *a | 150 mm (5.91 in.) or higher |
| *b | 3 mm (0.118 in.) or higher |
Cover the automatic high beam sensor with an opaque object, such as cardboard.
Make sure that there is no clearance between the cardboard or equivalent object and the area of the windshield glass in front of the automatic high beam sensor.
If there is any clearance, light may shine on the automatic high beam sensor and the value of the Data List will not change.
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Auto H Beam STS0 | Automatic high beam sensor state past 0 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
The Data List value displays "Speed".
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Using the GTS, read the Data List.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Auto High Beam Main Switch | Auto high beam switch signal / OFF or ON | OFF: Auto high beam switch off
ON: Auto high beam switch on |
- |
Normal condition listed above is displayed.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Using the GTS, read the Data List.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item / Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Auto H Beam STS0 | Automatic high beam sensor state past 0 / Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc, Delay, Aim Lmt, SAE Mod, Undefin, LIN Err | Condition can be displayed | - |
The Data List value displays "Daytime" or "Speed".
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Perform the Active Test according to the display on the GTS.
Click hereVehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM (for Halogen Headlight)>DATA LIST / ACTIVE TEST
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Automatic High Beam Indicator | Automatic high beam indicator light | OFF or ON | - |
Automatic high beam indicator light illuminate.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the auto high beam main switch.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM MAIN SWITCH>REMOVAL
Inspect the auto high beam main switch.
Click hereVehicle Exterior>LIGHTING (EXT)>AUTOMATIC HIGH BEAM MAIN SWITCH>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the G222 auto high beam switch connector.
Disconnect the G216 main body ECU (multiplex network body ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G222-5 (+B) - G216-23 (AHBI) | Always | Below 1 Ω |
| G222-2 (E) - Body ground | Always | Below 1 Ω |
| G222-5 (+B) or G216-23 (AHBI) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG