This DTC is stored when a malfunction occurs in the DAB tuner antenna which is connected to the radio and display receiver assembly.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B157D | DAB Tuner Antenna Disconnected | The DAB tuner antenna is not connected | ·
Digital audio broadcasting antenna assembly ·
No. 2 antenna cord sub-assembly ·
Windshield glass (window glass antenna wire) ·
Harness or connector ·
Radio and display receiver assembly |
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check if any optional components that may decrease reception capacity, such as a telephone antenna, are installed.
Optional components are installed.
Do not remove optional components without permission of the customer.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the windshield glass (window glass antenna wire).
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>WINDOW GLASS ANTENNA WIRE>REPAIR
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Radio and Display Receiver Assembly) |
| *b | Front view of wire harness connector
(to No. 2 Antenna Cord Sub-assembly) |
Disconnect the radio and display receiver assembly connector.
Disconnect the antenna connector from the No. 2 antenna cord sub-assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| DB-1 - 1 | Always | Below 1 Ω |
| DB-1-a - 1-a | Always | Below 1 Ω |
| DB-1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Vehicle Wire Harness) |
| *b | Front view of wire harness connector
(to Digital Audio Broadcasting Antenna Assembly) |
Disconnect the antenna connector from the vehicle wire harness.
Disconnect the antenna connector from the digital audio broadcasting antenna assembly.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 1 - 1 | Always | Below 1 Ω |
| 1-a - 1-a | Always | Below 1 Ω |
| 1 - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the digital audio broadcasting antenna assembly with a known good one.
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>DIGITAL AUDIO BROADCASTING ANTENNA>REMOVAL
Clear the DTCs.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
Recheck for DTCs and check that no DTCs are output.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>DTC CHECK / CLEAR
No DTCs are output.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereAudio / Visual / Telematics>AUDIO / VIDEO>RADIO RECEIVER (for Radio and Display Type)>REMOVAL