Home › Suspension › TIRE PRESSURE MONITORING › TIRE PRESSURE WARNING SYSTEM › from 2020.08
RM27T0E _53 Suspension _053710 TIRE PRESSURE MONITORING _0260907 TIRE PRESSURE WARNING SYSTEM J

TIRE PRESSURE MONITORING  TIRE PRESSURE WARNING SYSTEM  ECU Power Source Circuit  


DESCRIPTION

The IG circuit is the power source for the tire pressure warning ECU and receiver.

WIRING DIAGRAM

C444577E01
4.385,2.292 7.063,2.563 2.677,0.271 10 false Tire Pressure Warning ECU and Receiver 5.052,1.063 5.271,1.323 0.219,0.26 10 false IG 5.042,1.573 5.417,1.781 0.375,0.208 10 false GND 4.792,0.896 4.938,1.146 0.146,0.25 10 false 1 4.75,1.458 4.938,1.677 0.188,0.219 10 false 12 0.917,1.042 1.875,1.281 0.958,0.24 10 false from IG Circuit 3.177,1.26 4.417,1.51 1.24,0.25 10 false ECU-IG NO.1 3.958,2.292 4.333,2.5 0.375,0.208 10 false R41 0.573,0.365 2.719,0.604 2.146,0.24 10 false from Engine Stop and Start ECU 4.125,0.219 4.438,0.417 0.313,0.198 10 false *1 4.135,0.938 4.448,1.135 0.313,0.198 10 false *2 0.375,1.813 2.521,2.021 2.146,0.208 10 false *1: w/ Stop and Start System 0.375,2.208 2.521,2.417 2.146,0.208 10 false *2: w/o Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the tire pressure warning ECU and receiver, first use the GTS to record all of the current IDs and registered tires with transmitters (4 or 5 tires) of the tire pressure warning valve and transmitter registered to the tire pressure warning ECU and receiver.

·

It is necessary to perform initializationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>INITIALIZATION after registrationSuspension>TIRE PRESSURE MONITORING>TIRE PRESSURE WARNING SYSTEM>REGISTRATION of the transmitter IDs into the tire pressure warning ECU and receiver if the ECU has been replaced.



HINT:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER POWER SOURCE)
a.

Disconnect the R41 tire pressure warning ECU and receiver connector.


b.
C375025C60
0.281,0.792 0.677,1.052 0.396,0.26 2.219,1.469 2.75,1.771 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 2.792,1.708 3.25,1.906 0.458,0.198 10 false GND 0.344,0.844 0.802,1.042 0.458,0.198 10 false R41
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R41-12 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER POWER SOURCE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER POWER SOURCE)
a.
C375025C61
0.281,0.792 0.677,1.052 0.396,0.26 1.229,1.229 0.667,1.448 true 0.146,0.115 0.458,0.313 0.313,0.198 10 false *a 0.417,1.385 0.729,1.583 0.313,0.198 10 false IG 0.344,0.844 0.802,1.042 0.458,0.198 10 false R41
*a Front view of wire harness connector
(to Tire Pressure Warning ECU and Receiver)


Disconnect the R41 tire pressure warning ECU and receiver connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
R41-1 (IG) - Body ground Ignition switch ON 10 to 16 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG (w/o Stop and Start System)
NG (w/ Stop and Start System)



OK

NG (w/o Stop and Start System)

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG (w/ Stop and Start System)

GO TO STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)