The certification ECU (smart key ECU assembly) has a power source mode switching function.
This DTC is stored when the IGE input (the steering lock motor activation permission signal) sent directly from the certification ECU (smart key ECU assembly) to the steering lock ECU (steering lock actuator or upper bracket assembly) is determined to be abnormal.
The steering lock ECU (steering lock actuator or upper bracket assembly) is not connected to the CAN communication system. However, the steering lock ECU (steering lock actuator or upper bracket assembly) is connected to the certification ECU (smart key ECU assembly) via LIN communication and communicates with other components via CAN communication through the certification ECU (smart key ECU assembly).
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | Note |
|---|---|---|---|---|
| B2782 | Power Source Control ECU Malfunction | Either of the following conditions is met (1-trip detection logic (Only output while a malfunction is present and the engine switch is on (IG).)):
·
The steering lock motor activation command circuit has a short circuit. ·
The steering lock motor activation command circuit has an open circuit.
|
·
Steering lock ECU (steering lock actuator or upper bracket assembly) ·
Certification ECU (smart key ECU assembly) ·
Harness or connector |
DTC Output Confirmation Operation:
Perform a steering lock/unlock operation. (The steering locks when a door is opened with the shift lever in P* and the engine switch off. The steering unlocks when the engine switch is turned on (ACC) or on (IG) while carrying the electrical key transmitter sub-assembly.) |
*: for Automatic Transmission
| Vehicle Condition when Malfunction Detected | Fail-safe Function when Malfunction Detected |
|---|---|
| The steering cannot be locked or unlocked. For this reason, the engine cannot be started. | Prohibits the engine from being started. |
| DTC No. | Data List and Active Test |
|---|---|
| B2782 | - |
When using the GTS with the engine switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.
Before replacing the steering lock ECU (steering lock actuator or upper bracket assembly) or certification ECU (smart key ECU assembly), refer to the Service Bulletin.
After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".
When disconnecting the cable from the negative (-) battery terminal, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
When disconnecting and reconnecting the auxiliary battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
| *a | Component with harness connected
(Steering Lock ECU (Steering Lock Actuator or Upper Bracket Assembly)) |
| *b | Steering Lock Motor not Operating |
| *c | Steering Lock Motor Operating |
| *d | Waveform |
Using an oscilloscope, check the waveform.
| Item | Content |
|---|---|
| Tester Connection | G35-3 (IGE) - G35-1 (GND) |
| Tool Setting | 2 V/DIV., 200 ms./DIV. |
| Condition | Any door opened when conditions below met, and then steering lock motor activated:
·
Shift lever in P* ·
Steering lock unlocked in advance by carrying electrical key transmitter sub-assembly and turning engine switch on (IG) ·
After above conditions met, engine switch turned off |
| Specified Condition | Pulse generation
(See waveform) |
*: for Automatic Transmission
When taking measurements when the lock motor is stopped, it is not necessary to perform any operations.
In order to take measurements when the lock motor is operating, perform either of the following operations:
To unlock the steering, carry the electrical key transmitter sub-assembly and turn the engine switch on (ACC) or on (IG).
To lock the steering, turn the engine switch off with the shift lever in P*, and then open a door.
*: for Automatic Transmission
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.
Clear the DTCs.
Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR
Turn the engine switch off.
Disconnect the cable from the negative (-) battery terminal, wait for 30 seconds or more, and then reconnect the cable to the negative (-) battery terminal to clear the record of malfunctions stored in the Data List.
After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
| Proceed to |
|---|
| NEXT |
NEXT
Perform the DTC output confirmation operation.
Check if DTC B2782 is output.
Click hereSteering>STEERING COLUMN>STEERING LOCK SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC B2782 is not output. | A |
| DTC B2782 is output. | B |
A
B
for Power Tilt and Power Telescopic Steering Column:
for Manual Tilt and Manual Telescopic Steering Column:
Disconnect the G35 steering lock ECU (steering lock actuator or upper bracket assembly) connector.
Disconnect the G215 certification ECU (smart key ECU assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G35-3 (IGE) - G215-24 (SLR+) | Always | Below 1 Ω |
| G35-1 (GND) - Body ground | Always | Below 1 Ω |
| G35-3 (IGE) or G215-24 (SLR+) - Other terminals and body ground | Always | 10 kΩ or higher |
If the result is not as specified, check for looseness in the connection which leads to ground.
| Proceed to |
|---|
| OK |
| NG |
OK
NG