Home › Suspension › SUSPENSION CONTROL › AIR SUSPENSION SYSTEM › from 2020.08
RM27T0E _53 Suspension _053706 SUSPENSION CONTROL _0260870 AIR SUSPENSION SYSTEM C

SUSPENSION CONTROL  AIR SUSPENSION SYSTEM  C1789  Vehicle Identification Malfunction  


DESCRIPTION

·

When the absorber control ECU has not acquired the vehicle identification information, DTC C1789 is stored. When the vehicle identification information is correctly acquired, this DTC is cleared. Vehicle identification information is automatically acquired when the system enters test mode.

·

If an incorrect ECM is installed, the vehicle information will not match and DTC C1789 will be stored.


DTC Code DTC Detection Condition Trouble Area
C1789 One of the following conditions is met:
·

The vehicle identification information is not stored.

·

Vehicle identification information that is different from the stored information is received 3 times.

·

The stop and start system setting availability stored value is not stored.

·

When stored stop and start system setting is OFF, setting is determined to be ON.


·

Vehicle identification information

·

ECM

·

CAN communication system

·

Absorber control ECU



CAUTION / NOTICE / HINT

NOTICE:
·

Before performing troubleshooting, inspect the connectors of related circuits.

·

If DTC C1782 (Power Source Voltage Malfunction) is output at the same time, perform troubleshooting for C1782 first.

Click hereSuspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>C1782

·

Before replacing the absorber control ECU, perform all of the following:

*

If no malfunctions are found in other areas, replace the absorber control ECU.



·

After replacing the absorber control ECU with a new one, perform registration of vehicle identification information.

Click hereSuspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>TEST MODE PROCEDURE



PROCEDURE

1.CHECK FOR DTCS (CAN COMMUNICATION SYSTEM)

HINT:

If DTC C1781 (Suspension Control ECU Malfunction) is output at the same time, perform troubleshooting for C1781 first.


Result:
Result Proceed to
C1781 and CAN communication malfunction DTC are not output A
C1781 is output B
CAN communication DTC is output C



A

2.CHECK VEHICLE IDENTIFICATION INFORMATION STATUS

B

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

2.CHECK VEHICLE IDENTIFICATION INFORMATION STATUS
a.

Check that vehicle identification information has been stored.

Click hereSuspension>SUSPENSION CONTROL>AIR SUSPENSION SYSTEM>TEST MODE PROCEDURE


Result:
Result Proceed to
Information stored A
Information not stored B



A

3.READ VALUE USING GTS (STOP AND START LEARNING STATUS)

B

PERFORM VEHICLE IDENTIFICATION INFORMATION REGISTRATION

3.READ VALUE USING GTS (STOP AND START LEARNING STATUS)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / Air suspension / Data List.

Air Suspension
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
Stop and Start Learning Status Learning status of stop and start setting availability after vehicle identification information registration is performed /
Unset, OFF or ON
OFF: w/o Stop and Start System
ON: w/ Stop and Start System
-


f.

Check the value displayed on the GTS.

OK:

The display is as specified in the normal condition column.


Result:
Proceed to
OK
NG




OK

4.CHECK RELATED PART

NG

REPLACE SUSPENSION CONTROL ECU

4.CHECK RELATED PART
a.

If the DTC was output as a result of the replacement of a related part, replace the part with one that has a correct part number.

Related Part ECM

NOTICE:

When removing a related part to check it, be sure to follow the appropriate procedures and precautions.

Refer to the following procedures to remove the ECM.



HINT:

If parts have not been replaced and DTC C1789 is output, there may be an internal malfunction in the absorber control ECU. Therefore, replace the absorber control ECU.



Result:
Result Proceed to
The related part has an incorrect part number. A
The related part has the correct part number, or a related part and absorber control ECU have not been replaced. B



A

REPLACE RELATED PART WITH PART THAT HAS CORRECT PART NUMBER

B

REPLACE SUSPENSION CONTROL ECU