Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster) › from 2020.08
RM27T0E _54 Brake _053712 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0260911 VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  VEHICLE STABILITY CONTROL SYSTEM(for Hydraulic Brake Booster)  ABS Warning Light Remains ON  


DESCRIPTION

If any of the following is detected, the ABS warning light remains on.

·

The skid control ECU connector is disconnected from the skid control ECU.

·

There is a malfunction in the skid control ECU internal circuit.

·

There is an open in the harness between the combination meter and skid control ECU.

·

The anti-lock brake system is defective.

·

The voltage at terminal IG1 is high.

·

The rear differential is locked.*


*: w/ Rear Differential Lock


HINT:

It may not be possible to use the GTS when the skid control ECU is abnormal.


WIRING DIAGRAM

C449526E01
2.927,3.573 3.219,3.729 0.292,0.156 10 false RLP 3.302,3.583 3.479,3.74 0.177,0.156 10 false 12 3.24,4.667 5.344,5.188 2.104,0.521 10 false Rear Differential Lock Detection Switch (Differential Lock Indicator switch)*3 3.406,3.917 3.792,4.146 0.385,0.229 10 false *3 5.479,4.698 7.094,5.052 1.615,0.354 10 false Skid Control ECU (Master Cylinder Solenoid) 5.594,3.458 5.781,3.604 0.188,0.146 10 false 40 5.958,3.688 6.292,3.844 0.333,0.156 10 false EXI3 2.042,4.094 3.406,4.458 1.365,0.365 10 false 4 Wheel Drive Control ECU 0.604,3.26 1.854,3.646 1.25,0.385 10 false Combination Meter Assembly 1.042,4.823 2.969,4.99 1.927,0.167 10 false : CAN Communication System 0.125,5.573 2.635,5.802 2.51,0.229 10 false *3: w/ Rear Differential Lock 1.156,2.135 1.5,2.323 0.344,0.188 10 false ABS 1.406,0.927 1.594,1.083 0.188,0.156 10 false IG 2.542,2.958 2.729,3.115 0.188,0.156 10 false IG 5.604,0.646 5.781,0.792 0.177,0.146 10 false 46 6.01,0.833 6.271,0.99 0.26,0.156 10 false IG1 2.427,0.854 3.427,1.01 1,0.156 10 false from IG1 Circuit 5.969,2.083 6.385,2.229 0.417,0.146 10 false GND1 5.958,2.563 6.375,2.708 0.417,0.146 10 false GND2 5.958,3.031 6.375,3.177 0.417,0.146 10 false GND3 5.646,1.792 5.76,1.948 0.115,0.156 10 false 1 5.604,2.302 5.792,2.469 0.188,0.167 10 false 32 5.646,2.792 5.771,2.969 0.125,0.177 10 false 4 5.615,0.854 5.823,1.021 0.208,0.167 10 false A7 5.635,2.063 5.844,2.229 0.208,0.167 10 false A7 5.604,2.521 5.813,2.688 0.208,0.167 10 false A7 5.615,3 5.823,3.167 0.208,0.167 10 false A8 5.604,3.677 5.813,3.844 0.208,0.167 10 false A7 3.25,4.458 3.469,4.625 0.219,0.167 10 false E2 4.01,4.26 4.24,4.438 0.229,0.177 10 false +B 3.792,4.042 3.927,4.219 0.135,0.177 10 false 2 4.469,4.281 4.833,4.438 0.365,0.156 10 false GND 4.865,4.052 4.99,4.219 0.125,0.167 10 false 1 1.99,3.917 2.292,4.094 0.302,0.177 10 false G53 0.604,3.104 1.167,3.323 0.563,0.219 10 false G304 3.854,1.01 4.938,1.24 1.083,0.229 10 false ECU-IG NO. 1 4.594,0.708 4.927,0.906 0.333,0.198 10 false *1 4.594,1.406 4.927,1.604 0.333,0.198 10 false *2 3.302,1.531 3.844,1.76 0.542,0.229 10 false IG31 2.552,2.021 4.375,2.323 1.823,0.302 10 false Engine Stop and Start ECU 2.542,1.844 3.104,2.063 0.563,0.219 10 false G314 0.115,5.063 2.625,5.292 2.51,0.229 10 false *1: w/o Stop and Start System 0.125,5.313 2.635,5.542 2.51,0.229 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

NOTICE:

When replacing the master cylinder solenoid, perform calibration (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>CALIBRATION).


PROCEDURE

1.CHECK THAT SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED
a.

Check the skid control ECU connector connection.

OK:

The 2 connectors are securely connected.




OK

2.CHECK DTC

NG

CONNECT CONNECTOR TO ECU CORRECTLY

2.CHECK DTC
a.

Check for DTCs (See page Brake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC is not output A
DTC is output B



A

3.CHECK CAN COMMUNICATION LINE

B

3.CHECK CAN COMMUNICATION LINE
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (w/ Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM, w/o Central Gateway ECU: See page Power Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM).

OK:

CAN Bus Check indicates no malfunctions in CAN communication.


Result
Result Proceed to
OK A
NG (w/ Central Gateway ECU) B
NG (w/o Central Gateway ECU) C



A

4.READ VALUE USING GTS (IG1 VOLTAGE VALUE)

B

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

C

GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

4.READ VALUE USING GTS (IG1 VOLTAGE VALUE)

OK

5.CHECK TERMINAL VOLTAGE (EXI3)

NG

7.CHECK TERMINAL VOLTAGE (IG1)
5.CHECK TERMINAL VOLTAGE (EXI3)
a.

Disconnect the A7 skid control ECU connector.


b.
U148400E01
0.097,0.113 0.359,0.266 0.262,0.153 10 *a 2.624,0.422 2.972,0.594 0.348,0.172 10 EXI3 2.595,0.505 2.522,0.505 2.522,0.505 2.02,1.502 false 0.207,0.741 0.432,0.911 0.225,0.170 10 A7

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-40 (EXI3) - Body ground Ignition switch ON
w/ Rear Differential Lock: Rear differential free
11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))



OK

6.READ VALUE USING GTS (ABS WARNING LIGHT)

NG

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)
6.READ VALUE USING GTS (ABS WARNING LIGHT)
a.

Turn the ignition switch off.


b.

Connect the GTS to the DLC3.


c.

Turn the ignition switch to ON.


d.

Turn the GTS on.


e.

Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
ABS Warning Light ABS warning light/ ON or OFF OFF -


f.

When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List.

(See pageBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>VEHICLE STABILITY CONTROL SYSTEM (for Hydraulic Brake Booster)>DATA LIST / ACTIVE TEST)

ABS/VSC/TRC
Tester Display Test Part Control Range Diagnostic Note
ABS Warning Light ABS warning light Warning light ON/OFF Observe the combination meter.

Result
Result Proceed to
Data List Display Data List Display when Performing Active Test ON/OFF Operation
ON Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C
OFF Changes between ON and OFF A
Does not change between ON and OFF (for LHD) B
Does not change between ON and OFF (for RHD) C



A

GO TO METER / GAUGE SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING)

B

C

7.CHECK TERMINAL VOLTAGE (IG1)

A

8.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

C

INSPECT STOP AND START SYSTEM (BACKUP BOOST CONVERTER CIRCUIT)

8.CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL)
a.

Disconnect the A7 and A8 skid control ECU connectors.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-1 (GND1) - Body ground Always Below 1 Ω
A7-32 (GND2) - Body ground Always Below 1 Ω
A8-4 (GND3) - Body ground Always Below 1 Ω


Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPAIR OR REPLACE HARNESS OR CONNECTOR

B

C

9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU EXI3 CIRCUIT)
a.

Disconnect the A7 skid control ECU connector.


b.

Disconnect the G53 4 wheel drive control ECU connector.


c.

w/ Rear Differential Lock:

Disconnect the E2 rear differential lock detection switch connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A7-40 (EXI3) - Body ground Always 10 kΩ or higher


Result
Result Proceed to
OK (w/o Rear Differential Lock) A
OK (w/ Rear Differential Lock) B
NG C



A

10.CHECK TERMINAL VOLTAGE (EXI3)

B

11.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

10.CHECK TERMINAL VOLTAGE (EXI3)
a.

Disconnect the A7 skid control ECU connector.


b.

Connect the G53 4 wheel drive control ECU connector.


c.
U148400E01
0.097,0.113 0.359,0.266 0.262,0.153 10 *a 2.624,0.422 2.972,0.594 0.348,0.172 10 EXI3 2.595,0.505 2.522,0.505 2.522,0.505 2.02,1.502 false 0.207,0.741 0.432,0.911 0.225,0.170 10 A7

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-40 (EXI3) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

C

11.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)
a.

Remove the rear differential lock detection switch (See page Drivetrain>AXLE AND DIFFERENTIAL>REAR DIFFERENTIAL LOCK POSITION SWITCH>REMOVAL).


b.
C214518E02
0.25,0.339 0.586,0.676 0.336,0.336 10 *a 0.496,1.709 0.722,1.892 0.225,0.184 10 +B 2.541,1.76 2.901,1.935 0.360,0.174 10 GND 1.531,1.158 0.588,1.571 0.588,1.571 0.588,1.709 false 1.923,1.164 2.748,1.571 2.748,1.571 2.748,1.697 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
1 (GND) - 2 (+B) Pushed in Below 1 Ω
Not pushed in 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Rear Differential Lock Detection Switch)



OK

12.CHECK TERMINAL VOLTAGE (EXI3)

NG

REPLACE REAR DIFFERENTIAL LOCK DETECTION SWITCH (DIFFERENTIAL LOCK INDICATOR SWITCH)

12.CHECK TERMINAL VOLTAGE (EXI3)
a.

Disconnect the A7 skid control ECU connector.


b.

Connect the G53 4 wheel drive control ECU connector.


c.
U148400E01
0.097,0.113 0.359,0.266 0.262,0.153 10 *a 2.624,0.422 2.972,0.594 0.348,0.172 10 EXI3 2.595,0.505 2.522,0.505 2.522,0.505 2.02,1.502 false 0.207,0.741 0.432,0.911 0.225,0.170 10 A7

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A7-40 (EXI3) - Body ground Ignition switch ON 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))

Result
Result Proceed to
NG A
OK (for LHD) B
OK (for RHD) C



A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

C