Home › Power Source / Network › 1GD-FTV (BATTERY / CHARGING) › CHARGING SYSTEM › from 2020.08
RM27T0E _57 Power Source / Network _053727 1GD-FTV BATTERY / CHARGING _0261025 CHARGING SYSTEM C

1GD-FTV BATTERY / CHARGING  CHARGING SYSTEM  P161A87  Lost Communication with Alternator Missing Message  


DESCRIPTION

The ECM communicates with the generator assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P161A87 Lost Communication with Alternator Missing Message Generator assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic)
·

Wire harness or connector

·

Generator assembly

·

ECM


Charge warning light does not come on DTC stored SAE Code: P161A

WIRING DIAGRAM

A427236E26
0.063,0.708 1.521,1.375 1.458,0.667 10 false from 250A FL 1.75,0.875 2.563,1.094 0.813,0.219 10 false ALT-S 2.5,0.625 2.635,0.833 0.135,0.208 10 false 1 2.688,0.708 3.24,0.938 0.552,0.229 10 false +B 3.719,0.729 4.25,0.979 0.531,0.25 10 false LIN 4.063,0.573 4.313,0.802 0.25,0.229 10 false 2 2.417,1.167 2.802,1.427 0.385,0.26 10 false A95 2.427,1.323 4.542,1.552 2.115,0.229 10 false Battery State Sensor Assembly* 2.667,2.708 3.052,2.969 0.385,0.26 10 false C157 2.677,2.875 4.969,3.125 2.292,0.25 10 false Generator Assembly 1.083,3.177 3.198,3.406 2.115,0.229 10 false : LIN Communication Line 5.854,0.719 6.146,0.958 0.292,0.24 10 false LIN 5.583,0.542 5.833,0.771 0.25,0.229 10 false 7 6.063,1.813 6.469,2.042 0.406,0.229 10 false C152 6.073,1.979 6.583,2.208 0.51,0.229 10 false ECM 3.719,2.167 4.229,2.396 0.51,0.229 10 false LIN 4.052,2.052 4.302,2.281 0.25,0.229 10 false 2 1.031,3.469 6.385,3.667 5.354,0.198 10 false *: w/ Battery State Sensor Assembly 4.313,0.906 4.563,1.135 0.25,0.229 10 false *

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK CHARGING SYSTEM

Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

2.CHECK HARNESS AND CONNECTOR (ECM - GENERATOR ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the generator assembly connector.


c.

Disconnect the battery state sensor assembly connector.*


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C157-2 (LIN) - C152-7 (LIN) Always Below 1 Ω
A95-2 (LIN)* - C152-7 (LIN) Always Below 1 Ω
C157-2 (LIN) or C152-7 (LIN) - Body ground Always 10 kΩ or higher
A95-2 (LIN1)* or C152-7 (LIN) - Body ground Always 10 kΩ or higher


*: w/ Battery State Sensor Assembly


Result:
Result Proceed to
OK (w/ Battery State Sensor Assembly) A
OK (w/o Battery State Sensor Assembly) B
NG C



A

3.CLEAR DTC

B

5.INSPECT GENERATOR ASSEMBLY

C

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Check for DTCs, and then write them down.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Clear the DTCs.


h.

Turn the ignition switch off and wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

4.CHECK DTC OUTPUT
4.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Allow the engine to idle for approximately 17 minutes or more.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine and Transmission / Trouble Codes.


f.

Check for DTCs.


Result:
Result Proceed to
Only DTC P161A87 is output. A
DTC P161A87 and P162B87 are output. B
DTCs are not output. C



A

B

C