Home › Power Source / Network › 1GD-FTV (BATTERY / CHARGING) › CHARGING SYSTEM › from 2020.08
RM27T0E _57 Power Source / Network _053727 1GD-FTV BATTERY / CHARGING _0261025 CHARGING SYSTEM C

1GD-FTV BATTERY / CHARGING  CHARGING SYSTEM  P162B87  Lost Communication with Battery Monitor Module Missing Message  


DESCRIPTION

The ECM communicates with the battery state sensor assembly via LIN communication. If a LIN communication error is detected, the ECM stores this DTC.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P162B87 Lost Communication with Battery Monitor Module Missing Message Battery state sensor assembly or ECM communication stops for approximately 17 minutes or more with the ignition switch ON
(1 trip detection logic)
·

Wire harness or connector

·

Battery state sensor assembly

·

ECM


Charge warning light does not come on DTC stored SAE Code: P162B

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


PROCEDURE

1.CHECK BATTERY STATE SENSOR ASSEMBLY INSTALLATION CONDITION
a.

Check installation condition of the battery state sensor assembly.


Result:
Result
OK
NG



OK

2.CHECK CHARGING SYSTEM

NG

INSTALL THE BATTERY STATE SENSOR ASSEMBLY CORRECTLY

2.CHECK CHARGING SYSTEM

Result:
Result
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE CHARGING SYSTEM

3.CHECK HARNESS AND CONNECTOR (ECM - BATTERY STATE SENSOR ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the battery state sensor assembly connector.


c.

Disconnect the generator assembly connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C157-2 (LIN) - C152-7 (LIN) Always Below 1 Ω
A95-2 (LIN) - C152-7 (LIN) Always Below 1 Ω
C157-2 (LIN) or C152-7 (LIN) - Body ground Always 10 kΩ or higher
A95-2 (LIN1) or C152-7 (LIN) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Check that the battery state sensor assembly connector is securely connected.

OK:

The connector is securely connected.



b.

Disconnect the battery state sensor assembly connector.


c.

Check the connector case and terminals for deformation or corrosion.

OK:

No deformation or corrosion.



d.
A434715C25
1.5,0.115 2,0.365 0.5,0.25 0.75,1.667 1.531,1.167 true 0.083,0.052 0.396,0.25 0.313,0.198 10 false *a 0.635,1.688 1.073,1.906 0.438,0.219 10 false +B 1.625,0.146 2.083,0.344 0.458,0.198 10 false A95
*a Front view of wire harness connector
(to Battery State Sensor Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A95-1 (+B) - Body ground Always 11 to 14 V



Result:
Result
OK
NG



OK

5.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON.


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine / Trouble Codes.


e.

Check for DTCs, and note down any DTCs that are output.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Clear the DTCs.


h.

Turn the ignition switch off, wait 30 seconds.


Result:
Proceed to
NEXT



NEXT

6.CHECK DTC OUTPUT
6.CHECK DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Start the engine.


c.

Allow the engine to idle for approximately 17 minutes or more.


d.

Turn the GTS on.


e.

Enter the following menus: Powertrain / Engine / Trouble Codes.


f.

Check for DTCs.


Result:
Result Proceed to
Only DTC P162B87 is output A
DTC P161A87 and P162B87 are output. B
DTCs are not output. C



A

B

C