Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B161A  Lost Communication with Front Satellite Sensor Bus  


DESCRIPTION

The front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit) is composed of the center airbag sensor, front airbag sensor RH and front airbag sensor LH.

The front airbag sensor RH or front airbag sensor LH detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.

DTC B161A is stored when a malfunction is detected in the front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit).

DTC Code DTC Detection Condition Trouble Area
B161A One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the front collision sensor circuit (front airbag sensor RH circuit and front airbag sensor LH circuit).

·

A front airbag sensor RH malfunction.

·

A front airbag sensor LH malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Engine room main wire

·

Front airbag sensor RH

·

Front airbag sensor LH

·

Center airbag sensor



WIRING DIAGRAM

C210945E04
0.376,2.206 0.649,2.369 0.274,0.163 10 A20 0.375,2.377 1.882,2.540 1.507,0.163 10 Front Airbag Sensor RH 5.564,4.742 5.838,4.904 0.274,0.163 10 G1 5.564,4.913 6.715,5.246 1.151,0.333 10 Center Airbag Sensor Assembly 1.276,0.828 1.606,1.004 0.331,0.176 10 +SR 3.514,0.828 3.810,1.004 0.296,0.176 10 GA5 3.514,1.627 3.810,1.802 0.296,0.176 10 GA5 3.514,3.397 3.810,3.572 0.296,0.176 10 GA5 3.514,4.205 3.810,4.380 0.296,0.176 10 GA5 5.321,0.721 5.502,0.876 0.180,0.155 10 29 5.321,1.533 5.502,1.689 0.180,0.155 10 27 1.733,0.721 1.841,0.870 0.107,0.149 10 2 3.586,0.647 3.693,0.796 0.107,0.149 10 1 3.586,1.446 3.693,1.595 0.107,0.149 10 2 1.276,1.637 1.555,1.813 0.280,0.176 10 -SR 5.671,0.828 6.001,1.004 0.331,0.176 10 +SR 5.671,1.637 5.951,1.813 0.280,0.176 10 -SR 1.733,1.533 1.841,1.682 0.107,0.149 10 1 0.376,4.733 0.649,4.896 0.274,0.163 10 A21 0.375,4.905 1.882,5.068 1.507,0.163 10 Front Airbag Sensor LH 1.276,3.398 1.606,3.573 0.331,0.176 10 +SL 5.321,3.29 5.502,3.445 0.180,0.155 10 30 5.321,4.103 5.502,4.258 0.180,0.155 10 28 1.735,3.29 1.842,3.439 0.107,0.149 10 2 3.601,3.217 3.708,3.365 0.107,0.149 10 3 3.601,4.029 3.708,4.178 0.107,0.149 10 4 1.276,4.207 1.555,4.382 0.280,0.176 10 -SL 5.671,3.412 6.002,3.587 0.331,0.176 10 +SL 5.671,4.221 5.951,4.396 0.280,0.176 10 -SL 1.735,4.103 1.842,4.252 0.107,0.149 10 1

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.


b.

Turn the ignition switch off.

HINT:

If a communication error occurs, DTCs for both the LH and RH sides will be stored simultaneously. To identify the malfunctioning area, turn the ignition switch off and then to ON again.



c.

Turn the ignition switch to ON, and wait for at least 60 seconds.


d.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

Result
Result Proceed to
DTC B1613 is output. A
DTC B1618 is output. B
DTCs B1613 and B1618 are not output. C

HINT:
·

DTCs indicating communication errors will be changed to DTCs indicating errors in initialization by turning the ignition switch off and then to ON again.

·

Codes other than DTCs B1613 and B1618 may be output at this time, but they are not related to this check.





C

2.CHECK CENTER AIRBAG SENSOR

A

B

2.CHECK CENTER AIRBAG SENSOR
a.

Turn the ignition switch to ON, and wait for at least 60 seconds.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B161A is not output.


HINT:

Codes other than DTC B161A may be output at this time, but they are not related to this check.




OK

NG