Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1656  Seat Belt Buckle Switch (LH)  


DESCRIPTION

The seat belt buckle switch LH circuit consists of the center airbag sensor and front seat inner belt LH.

DTC B1656 is stored when a malfunction is detected in the seat belt buckle switch LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1656 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat belt buckle switch LH circuit for 2 seconds.

·

A front seat inner belt LH malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat inner belt assembly LH (Seat belt buckle switch LH)

·

Center airbag sensor



WIRING DIAGRAM

C213926E24
2.417,1.49 2.667,1.719 0.25,0.229 10 false 2 2.438,3.052 2.563,3.219 0.125,0.167 10 false 1 1.969,1.24 2.365,1.396 0.396,0.156 10 false LBE+ 1.969,3.094 2.344,3.24 0.375,0.146 10 false LBE- 5.875,2.958 6.271,3.104 0.396,0.146 10 false LBE- 5.875,1.365 6.281,1.531 0.406,0.167 10 false LBE+ 5.604,1.479 5.854,1.646 0.25,0.167 10 false 10 5.604,3.063 5.854,3.229 0.25,0.167 10 false 18 0.406,3.979 0.76,4.125 0.354,0.146 10 false R48 0.406,4.146 1.969,4.292 1.563,0.146 10 false Front Seat Inner Belt LH 5.604,3.948 5.979,4.167 0.375,0.219 10 false R49 5.604,4.125 6.99,4.302 1.385,0.177 10 false Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



PROCEDURE

1.CHECK FOR DTC
a.

Turn the ignition switch to ON.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




OK

NG

2.CHECK CONNECTION OF CONNECTORS
2.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

OK:

The connectors are properly connected.




OK

3.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

3.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front seat inner belt LH.


b.
C208244C41
0.385,1.302 0.698,1.458 0.313,0.156 10 false *1 2.188,1.75 2.5,1.906 0.313,0.156 10 false *2
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor


Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged.

OK:

The connectors are not deformed or damaged.




OK

4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

C385812C01
4.958,0.458 5.292,0.698 0.333,0.24 2.885,0.531 3.208,0.76 0.323,0.229 3.229,1.135 3.552,0.938 true 4.125,1.156 3.76,0.938 true 6.385,1.208 6.021,0.99 true 6.021,0.781 6.344,0.583 true 0.625,0.865 0.938,1.063 0.313,0.198 10 false *1 1.823,1.135 2.135,1.333 0.313,0.198 10 false *2 1.635,0.698 1.948,0.896 0.313,0.198 10 false A 1.375,0.677 1.688,0.875 0.313,0.198 10 false B 1.104,0.677 1.417,0.875 0.313,0.198 10 false C 1.188,0.344 1.5,0.542 0.313,0.198 10 false *3 3.573,0.271 3.885,0.469 0.313,0.198 10 false *a 5.729,0.198 6.042,0.396 0.313,0.198 10 false *b 3.969,0.427 4.281,0.625 0.313,0.198 10 false *4 6.188,0.302 6.5,0.5 0.313,0.198 10 false *5 4,1.167 4.615,1.365 0.615,0.198 10 false LBE+ 3.042,1.156 3.656,1.354 0.615,0.198 10 false LBE- 6.365,0.521 6.979,0.719 0.615,0.198 10 false LBE+ 6.417,1.146 7.031,1.344 0.615,0.198 10 false LBE- 2.917,0.563 3.25,0.781 0.333,0.219 10 false R48 5,0.49 5.333,0.708 0.333,0.219 10 false R49 0.781,0.469 1.094,0.667 0.313,0.198 10 false D
*1 Front Seat Inner Belt LH *2 Center Airbag Sensor
*3 No. 2 Floor Wire *4 Connector C
*5 Connector B - -
*a Front view of wire harness connector
(to Front Seat Inner Belt LH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)



b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R48-2 (LBE+) - Body ground Ignition switch ON Below 1 V
R48-1 (LBE-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R48-2 (LBE+) - R49-10 (LBE+) Always Below 1 Ω
R48-1 (LBE-) - R49-18 (LBE-) Always Below 1 Ω
R48-2 (LBE+) - Body ground Always 1 MΩ or higher
R48-1 (LBE-) - Body ground Always 1 MΩ or higher




OK

5.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)
a.
C146229C59
0.854,0.99 1.021,1.146 0.167,0.156 10 false *1 1.823,1.313 1.99,1.479 0.167,0.167 10 false *2
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor


Connect the connectors to the center airbag sensor and front seat inner belt LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




OK

NG

6.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
6.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

7.CHECK CENTER AIRBAG SENSOR
7.CHECK CENTER AIRBAG SENSOR
a.
C146229C60
0.854,0.99 1.021,1.146 0.167,0.156 10 false *1 1.823,1.313 1.99,1.479 0.167,0.167 10 false *2
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor


Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1656 is not output.


HINT:

Codes other than DTC B1656 may be output at this time, but they are not related to this check.




OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG