Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1655  Seat Belt Buckle Switch (D Seat Side)  


DESCRIPTION

The seat belt buckle switch LH or RH circuit consists of the center airbag sensor and front seat inner belt LH or RH.

DTC B1655 is stored when a malfunction is detected in the seat belt buckle switch LH or RH circuit.

DTC Code DTC Detection Condition Trouble Area
B1655 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat belt buckle switch circuit for 2 seconds.

·

A front seat inner belt malfunction.

·

A center airbag sensor malfunction.


·

No. 2 floor wire

·

Front seat inner belt assembly LH (Seat belt buckle switch LH) (for LHD)

·

Front seat inner belt assembly RH (Seat belt buckle switch RH) (for RHD)

·

Center airbag sensor



WIRING DIAGRAM

C213926E22
5.719,4.094 7.115,4.281 1.396,0.188 10 false Center Airbag Sensor 0.406,4.146 2.417,4.354 2.01,0.208 10 false Front Seat Inner Belt LH 5.865,2.917 6.344,3.198 0.479,0.281 10 false DBE- 5.719,3.906 6.052,4.083 0.333,0.177 10 false R1 0.406,3.948 0.865,4.198 0.458,0.25 10 false R48 5.875,1.354 6.323,1.646 0.448,0.292 10 false DBE+ 1.99,3.094 2.396,3.396 0.406,0.302 10 false LBE- 2.01,1.229 2.552,1.531 0.542,0.302 10 false LBE+ 5.563,3.094 5.896,3.385 0.333,0.292 10 false 12 5.573,1.5 5.927,1.802 0.354,0.302 10 false 11 2.458,3.094 2.823,3.385 0.365,0.292 10 false 1 2.458,1.521 2.698,1.813 0.24,0.292 10 false 2 0.063,0.104 1.198,0.323 1.135,0.219 12 false for LHD:

C213926E17
2.419,1.492 2.672,1.717 0.253,0.225 10 2 2.437,3.061 2.558,3.231 0.121,0.170 10 1 1.968,1.242 2.370,1.398 0.401,0.156 10 RBE+ 1.968,3.096 2.349,3.245 0.380,0.149 10 RBE- 5.873,2.963 6.272,3.112 0.399,0.149 10 DBE- 5.873,1.373 6.279,1.542 0.406,0.170 10 DBE+ 5.599,1.485 5.846,1.654 0.246,0.170 10 11 5.599,3.073 5.846,3.242 0.246,0.170 10 12 0.409,3.967 1.326,4.109 0.917,0.142 10 Q34 5.723,3.911 6.641,4.053 0.917,0.142 10 Q25 0.409,4.128 1.974,4.277 1.566,0.149 10 Front Seat Inner Belt RH 0.371,0.094 1.465,0.334 1.093,0.240 12 for RHD: 5.719,4.058 7.104,4.235 1.385,0.177 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result
Result Proceed to
for RHD A
for LHD B



B

2.CHECK FOR DTC

A

9.CHECK FOR DTC
2.CHECK FOR DTC
a.

Turn the ignition switch to ON.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK CONNECTION OF CONNECTORS
3.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt LH.

OK:

The connectors are properly connected.




OK

4.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

4.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front seat inner belt LH.


b.
C215710E04
0.354,1.354 0.521,1.531 0.167,0.177 10 false *1 2.135,1.5 2.302,1.677 0.167,0.177 10 false *2

Check that the connectors (on the center airbag sensor side and front seat inner belt LH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor



OK

5.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT LH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U170169E01
1.238,0.358 1.408,0.507 0.170,0.149 10 *3 0.188,1.332 0.350,1.495 0.163,0.163 10 *1 1.428,1.395 1.590,1.558 0.163,0.163 10 *2 1.568,0.904 1.696,1.053 0.128,0.149 10 A 1.245,1.115 1.374,1.264 0.128,0.149 10 B 0.923,1.115 1.051,1.264 0.128,0.149 10 C 0.587,0.904 0.715,1.053 0.128,0.149 10 D 4.075,1.161 4.461,1.324 0.385,0.163 10 LBE+ 2.773,1.143 3.158,1.305 0.385,0.163 10 LBE- 3.501,0.183 3.678,0.339 0.177,0.156 10 *a 4.026,0.498 4.203,0.661 0.177,0.163 10 *4 2.765,0.47 3.054,0.626 0.289,0.156 10 R48 6.607,1.385 6.992,1.548 0.385,0.163 10 DBE+ 5.04,1.385 5.425,1.548 0.385,0.163 10 DBE- 5.869,0.183 6.046,0.339 0.177,0.156 10 *b 6.499,0.498 6.676,0.661 0.177,0.163 10 *5 5.127,0.472 5.336,0.634 0.209,0.161 10 R1 6.209,1.158 6.579,1.454 false 6.071,1.158 5.405,1.456 false 3.432,1.038 3.143,1.196 false 3.768,1.038 4.049,1.206 false 1.123,0.918 1.123,0.414 1.123,0.414 1.193,0.414 false

Text in Illustration
*1 Front Seat Inner Belt LH *2 Center Airbag Sensor
*3 No. 2 Floor Wire *4 Connector C
*5 Connector B - -
*a Front view of wire harness connector
(to Front Seat Inner Belt LH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R48-2 (LBE+) - Body ground Ignition switch ON Below 1 V
R48-1 (LBE-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R48-2 (LBE+) - R1-11 (DBE+) Always Below 1 Ω
R48-1 (LBE-) - R1-12 (DBE-) Always Below 1 Ω
R48-2 (LBE+) - Body ground Always 1 MΩ or higher
R48-1 (LBE-) - Body ground Always 1 MΩ or higher




OK

6.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE NO. 2 FLOOR WIRE

6.CHECK FRONT SEAT INNER BELT LH (SEAT BELT BUCKLE SWITCH)
a.
C157773E01
0.738,1.272 0.903,1.455 0.165,0.184 10 *1 1.758,1.34 1.923,1.524 0.165,0.184 10 *2

Connect the connectors to the center airbag sensor and front seat inner belt LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor



OK

NG

7.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
7.REPLACE FRONT SEAT INNER BELT ASSEMBLY LH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

8.CHECK CENTER AIRBAG SENSOR
8.CHECK CENTER AIRBAG SENSOR
a.
C157773E01
0.738,1.272 0.903,1.455 0.165,0.184 10 *1 1.758,1.34 1.923,1.524 0.165,0.184 10 *2

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY LH

NG

9.CHECK FOR DTC
a.

Turn the ignition switch to ON.



c.

Turn the ignition switch off.


d.

Turn the ignition switch to ON, and wait for at least 60 seconds.


e.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.




OK

NG

10.CHECK CONNECTION OF CONNECTORS
10.CHECK CONNECTION OF CONNECTORS
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Check that the connectors are properly connected to the center airbag sensor and front seat inner belt RH.

OK:

The connectors are properly connected.




OK

11.CHECK CONNECTORS

NG

CONNECT CONNECTORS PROPERLY

11.CHECK CONNECTORS
a.

Disconnect the connectors from the center airbag sensor and front seat inner belt RH.


b.
C215710E05
0.354,1.354 0.521,1.531 0.167,0.177 10 false *1 2.135,1.5 2.302,1.677 0.167,0.177 10 false *2

Check that the connectors (on the center airbag sensor side and front seat inner belt RH side) are not damaged.

OK:

The connectors are not deformed or damaged.


Text in Illustration
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor



OK

12.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)

NG

REPLACE NO. 2 FLOOR WIRE

12.CHECK NO. 2 FLOOR WIRE (CENTER AIRBAG SENSOR - FRONT SEAT INNER BELT RH)
a.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

U170170E01
1.238,0.358 1.408,0.507 0.170,0.149 10 *3 0.188,1.332 0.350,1.495 0.163,0.163 10 *1 1.428,1.395 1.590,1.558 0.163,0.163 10 *2 1.568,0.904 1.696,1.053 0.128,0.149 10 A 1.245,1.115 1.374,1.264 0.128,0.149 10 B 0.923,1.115 1.051,1.264 0.128,0.149 10 C 0.587,0.904 0.715,1.053 0.128,0.149 10 D 4.079,1.161 4.464,1.324 0.385,0.163 10 RBE+ 2.748,1.143 3.133,1.305 0.385,0.163 10 RBE- 3.501,0.183 3.678,0.339 0.177,0.156 10 *a 4.026,0.498 4.203,0.661 0.177,0.163 10 *4 6.607,1.385 6.992,1.548 0.385,0.163 10 DBE+ 5.04,1.385 5.425,1.548 0.385,0.163 10 DBE- 5.869,0.183 6.046,0.339 0.177,0.156 10 *b 6.499,0.498 6.676,0.661 0.177,0.163 10 *5 5.104,0.463 5.400,0.619 0.296,0.156 10 Q25 2.726,0.463 3.030,0.619 0.304,0.156 10 Q34 6.209,1.158 6.579,1.454 false 6.071,1.158 5.405,1.456 false 3.432,1.038 3.143,1.196 false 3.768,1.038 4.049,1.206 false 1.123,0.918 1.123,0.414 1.123,0.414 1.193,0.414 false

Text in Illustration
*1 Front Seat Inner Belt RH *2 Center Airbag Sensor
*3 No. 2 Floor Wire *4 Connector C
*5 Connector B - -
*a Front view of wire harness connector
(to Front Seat Inner Belt RH)
*b Rear view of wire harness connector
(to Center Airbag Sensor)


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
Q34-2 (RBE+) - Body ground Ignition switch ON Below 1 V
Q34-1 (RBE-) - Body ground Ignition switch ON Below 1 V



c.

Turn the ignition switch off.


d.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
Q34-2 (RBE+) - Q25-11 (DBE+) Always Below 1 Ω
Q34-1 (RBE-) - Q25-12 (DBE-) Always Below 1 Ω
Q34-2 (RBE+) - Body ground Always 1 MΩ or higher
Q34-1 (RBE-) - Body ground Always 1 MΩ or higher




OK

13.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)

NG

REPLACE NO. 2 FLOOR WIRE

13.CHECK FRONT SEAT INNER BELT RH (SEAT BELT BUCKLE SWITCH)
a.
C157773E01
0.738,1.272 0.903,1.455 0.165,0.184 10 *1 1.758,1.34 1.923,1.524 0.165,0.184 10 *2

Connect the connectors to the center airbag sensor and front seat inner belt LH.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt LH
*2 Center Airbag Sensor



OK

NG

14.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
14.REPLACE FRONT SEAT INNER BELT ASSEMBLY RH
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Replace the front seat inner belt LH (See page Vehicle Interior>SEAT BELT>FRONT SEAT INNER BELT ASSEMBLY>REMOVAL).

HINT:

Perform the inspection using parts from a normally functioning vehicle if possible.




NEXT

15.CHECK CENTER AIRBAG SENSOR
15.CHECK CENTER AIRBAG SENSOR
a.
C157773E01
0.738,1.272 0.903,1.455 0.165,0.184 10 *1 1.758,1.34 1.923,1.524 0.165,0.184 10 *2

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


b.

Turn the ignition switch to ON, and wait for at least 60 seconds.



d.

Turn the ignition switch off.


e.

Turn the ignition switch to ON, and wait for at least 60 seconds.


f.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1655 is not output.


HINT:

Codes other than DTC B1655 may be output at this time, but they are not related to this check.


Text in Illustration
*1 Front Seat Inner Belt RH
*2 Center Airbag Sensor



OK

REPLACE FRONT SEAT INNER BELT ASSEMBLY RH

NG