Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1860  Short in Knee Airbag (D Side) Squib Circuit  B1861  Open in Knee Airbag (D Side) Squib Circuit  B1862  Short in Knee Airbag (D Side) Squib Circuit (to Ground)  B1863  Short in Knee Airbag (D Side) Squib Circuit (to +B)  


DESCRIPTION

The driver side knee squib circuit consists of the center airbag sensor and lower No. 1 instrument panel airbag.

This circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the driver side knee squib circuit.

DTC Code DTC Detection Condition Trouble Area
B1860 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the driver side knee squib circuit during the primary check.

·

A driver side knee squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee squib)

·

Center airbag sensor


B1861 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal in the driver side knee squib circuit for 2 seconds.

·

A driver side knee squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee squib)

·

Center airbag sensor


B1862 One of the following conditions is met:
·

The airbag sensor center detects a short circuit to ground signal in the driver side knee squib circuit for 0.5 seconds.

·

A driver side knee squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee squib)

·

Center airbag sensor


B1863 One of the following conditions is met:
·

The airbag sensor center detects a short circuit to B+ signal in the driver side knee squib circuit for 0.5 seconds.

·

A driver side knee squib malfunction.

·

A center airbag sensor malfunction.


·

Instrument panel wire

·

Lower No. 1 instrument panel airbag assembly (Driver side knee squib)

·

Center airbag sensor



WIRING DIAGRAM

C146265E21
0.754,2.937 1.077,3.135 0.323,0.198 10 G32 0.754,3.071 2.298,3.255 1.544,0.184 10 Driver Side Knee Squib 2.103,1.52 2.397,1.685 0.295,0.165 10 DK+ 2.137,2.52 2.395,2.685 0.258,0.165 10 DK- 2.489,2.313 2.627,2.469 0.137,0.156 10 2 2.492,1.498 2.630,1.691 0.137,0.193 10 1 4.598,1.509 4.727,1.702 0.128,0.193 10 9 4.537,2.314 4.711,2.461 0.174,0.147 10 10 4.817,1.585 5.131,1.759 0.313,0.174 10 DK+ 4.817,2.416 5.131,2.590 0.313,0.174 10 DK- 4.739,4.079 5.034,4.226 0.295,0.147 10 G1 4.74,4.24 6.118,4.433 1.378,0.193 10 Center Airbag Sensor

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK LOWER NO. 1 INSTRUMENT PANEL AIRBAG (DRIVER SIDE KNEE SQUIB)
a.

Turn the ignition switch off.

C385404C01
5.865,1.667 5.667,1.448 false 0.146,0.031 0.458,0.188 0.313,0.156 10 false *A 0.156,1.552 0.469,1.708 0.313,0.156 10 false *B 0.917,0.167 1.229,0.323 0.313,0.156 10 false *1 1.573,1.073 1.885,1.229 0.313,0.156 10 false *2 6.094,0.875 6.406,1.031 0.313,0.156 10 false *3 5.927,1.604 6.24,1.76 0.313,0.156 10 false *4 5.281,0.688 5.594,0.844 0.313,0.156 10 false *a 1.719,0.323 1.875,0.479 0.156,0.156 10 false A 0.927,1.802 1.24,1.958 0.313,0.156 10 false *1 1.615,2.521 1.927,2.677 0.313,0.156 10 false *2 1.708,2 1.865,2.156 0.156,0.156 10 false A 1.104,0.542 1.26,0.698 0.156,0.156 10 false D 1.281,0.542 1.438,0.698 0.156,0.156 10 false C 1.094,2.219 1.25,2.375 0.156,0.156 10 false D 1.271,2.219 1.427,2.375 0.156,0.156 10 false C 4.594,0.958 5.052,1.156 0.458,0.198 10 false G32
*A w/o Side Airbag *B w/ Side Airbag
*1 Driver Side Knee Squib *2 Center Airbag Sensor
*3 Connector C *4 SST
*a Front view of wire harness connector
(to Driver Side Knee Squib)
- -



b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connector from the lower No. 1 instrument panel airbag.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the lower No. 1 instrument panel airbag (driver side knee squib) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.




OK

REPLACE LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

NG

2.CHECK CONNECTOR
2.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C385405C01
0.365,0.177 0.677,0.333 0.313,0.156 10 false *A 0.375,2.833 0.688,2.99 0.313,0.156 10 false *B 0.792,0.5 1.104,0.656 0.313,0.156 10 false *1 1.729,1.729 2.042,1.885 0.313,0.156 10 false *2 0.781,3.094 1.094,3.25 0.313,0.156 10 false *1 1.719,4 2.031,4.156 0.313,0.156 10 false *2 1.875,0.698 2.031,0.896 0.156,0.198 10 false A 1.854,3.344 2.01,3.542 0.156,0.198 10 false A 1.292,1.01 1.448,1.208 0.156,0.198 10 false C 1.063,1.01 1.219,1.208 0.156,0.198 10 false D 1.021,3.583 1.177,3.781 0.156,0.198 10 false D 1.271,3.594 1.427,3.792 0.156,0.198 10 false C
*A w/o Side Airbag
*B w/ Side Airbag
*1 Driver Side Knee Squib
*2 Center Airbag Sensor


Check that the instrument panel wire connector (on the lower No. 1 instrument panel airbag side) is not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

3.CHECK INSTRUMENT PANEL WIRE (LOWER NO. 1 INSTRUMENT PANEL AIRBAG - CENTER AIRBAG SENSOR)

NG

REPLACE INSTRUMENT PANEL WIRE

3.CHECK INSTRUMENT PANEL WIRE (LOWER NO. 1 INSTRUMENT PANEL AIRBAG - CENTER AIRBAG SENSOR)
a.

Disconnect the connectors from the center airbag sensor.

C385406C01
5.042,1.698 5.458,1.396 true 5.927,1.708 5.563,1.417 true 0.208,0.063 0.521,0.219 0.313,0.156 10 false *A 0.229,1.5 0.542,1.656 0.313,0.156 10 false *B 1,0.208 1.313,0.365 0.313,0.156 10 false *1 1.438,0.198 1.75,0.354 0.313,0.156 10 false *2 1.802,1.104 2.115,1.26 0.313,0.156 10 false *3 5.958,1.031 6.271,1.188 0.313,0.156 10 false *4 5.396,0.896 5.708,1.052 0.313,0.156 10 false *a 4.896,1.719 5.25,1.917 0.354,0.198 10 false DK+ 4.885,1.094 5.344,1.292 0.458,0.198 10 false G32 5.854,1.729 6.208,1.927 0.354,0.198 10 false DK- 1,1.781 1.313,1.938 0.313,0.156 10 false *1 1.417,1.76 1.729,1.917 0.313,0.156 10 false *2 1.833,2.469 2.146,2.625 0.313,0.156 10 false *3 1.927,0.365 2.083,0.563 0.156,0.198 10 false A 1.927,1.969 2.083,2.167 0.156,0.198 10 false A 1.625,0.615 1.781,0.813 0.156,0.198 10 false B 1.354,0.615 1.51,0.813 0.156,0.198 10 false C 1.146,0.615 1.302,0.813 0.156,0.198 10 false D 1.625,2.208 1.781,2.406 0.156,0.198 10 false B 1.333,2.208 1.49,2.406 0.156,0.198 10 false C 1.167,2.208 1.323,2.406 0.156,0.198 10 false D
*A w/o Side Airbag *B w/ Side Airbag
*1 Driver Side Knee Squib *2 Instrument Panel Wire
*3 Center Airbag Sensor *4 Connector C
*a Front view of wire harness connector
(to Driver Side Knee Squib)
- -



b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
G32-1 (DK+) - Body ground Ignition switch ON Below 1 V
G32-2 (DK-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-1 (DK+) - G32-2 (DK-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G32-1 (DK+) - G32-2 (DK-) Always 1 MΩ or higher
G32-1 (DK+) - Body ground Always 1 MΩ or higher
G32-2 (DK-) - Body ground Always 1 MΩ or higher




OK

4.CHECK CENTER AIRBAG SENSOR

NG

REPLACE INSTRUMENT PANEL WIRE

4.CHECK CENTER AIRBAG SENSOR
a.
C385407C01
0.167,0.25 0.479,0.406 0.313,0.156 10 false *A 0.208,2.594 0.521,2.75 0.313,0.156 10 false *B 0.802,0.615 1.115,0.771 0.313,0.156 10 false *1 1.583,1.76 1.896,1.917 0.313,0.156 10 false *2 0.813,3.094 1.125,3.25 0.313,0.156 10 false *1 1.604,3.969 1.917,4.125 0.313,0.156 10 false *2 1.708,0.771 1.865,0.969 0.156,0.198 10 false A 1.188,1.063 1.344,1.26 0.156,0.198 10 false C 1.031,1.063 1.188,1.26 0.156,0.198 10 false D 1.052,3.573 1.208,3.771 0.156,0.198 10 false D 1.208,3.573 1.365,3.771 0.156,0.198 10 false C 1.74,3.292 1.896,3.49 0.156,0.198 10 false A
*A w/o Side Airbag
*B w/ Side Airbag
*1 Driver Side Knee Squib
*2 Center Airbag Sensor


Connect the connectors to the lower No. 1 instrument panel airbag and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1860, B1861, B1862 or B1863 is not output.


HINT:

Codes other than DTC B1860, B1861, B1862 and B1863 may be output at this time, but they are not related to this check.




OK

NG