Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM › from 2020.08
RM27T0E _58 Vehicle Interior _053735 SUPPLEMENTAL RESTRAINT SYSTEMS _0261086 AIRBAG SYSTEM C

SUPPLEMENTAL RESTRAINT SYSTEMS  AIRBAG SYSTEM  B1835  Short in Curtain Shield Airbag (LH) Squib Circuit  B1836  Open in Curtain Shield Airbag (LH) Squib Circuit  B1837  Short in Curtain Shield Airbag (LH) Squib Circuit (to Ground)  B1838  Short in Curtain Shield Airbag (LH) Squib Circuit (to +B)  


DESCRIPTION

The curtain shield squib LH circuit consists of the center airbag sensor and curtain shield airbag LH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib LH circuit.

DTC Code DTC Detection Condition Trouble Area
B1835 One of the following conditions is met:
·

The center airbag sensor detects a line short circuit signal 5 times in the curtain shield squib LH circuit during the primary check.

·

A curtain shield squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Center airbag sensor


B1836 One of the following conditions is met:
·

The center airbag sensor detects open circuit signal in the curtain shield squib LH circuit for 2 seconds.

·

A curtain shield squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Center airbag sensor


B1837 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to ground signal in the curtain shield squib LH circuit for 0.5 seconds.

·

A curtain shield squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Center airbag sensor


B1838 One of the following conditions is met:
·

The center airbag sensor detects a short circuit to B+ signal in the curtain shield squib LH circuit for 0.5 seconds.

·

A curtain shield squib LH malfunction.

·

A center airbag sensor malfunction.


·

Floor wire

·

Curtain shield airbag assembly LH (Curtain shield squib LH)

·

Center airbag sensor



WIRING DIAGRAM

U169903E03
0.74,3.24 3.135,3.406 2.396,0.167 10 false Curtain Shield Squib LH 2.052,1.521 2.427,1.708 0.375,0.188 10 false ICL+ 0.188,0.031 1.25,0.344 1.063,0.313 12 false for 5 Door: 4.771,1.625 5.167,1.813 0.396,0.188 10 false ICL+ 2.073,2.344 2.427,2.531 0.354,0.188 10 false ICL- 4.781,2.469 5.177,2.656 0.396,0.188 10 false ICL- 2.458,1.5 2.604,1.667 0.146,0.167 10 false 1 2.479,2.344 2.635,2.5 0.156,0.156 10 false 2 4.583,1.531 4.698,1.698 0.115,0.167 10 false 4 4.583,2.375 4.698,2.542 0.115,0.167 10 false 3 4.76,4.167 5.083,4.354 0.323,0.188 10 false R49 4.75,4.302 6.198,4.51 1.448,0.208 10 false Center Airbag Sensor 0.74,3.042 1.094,3.198 0.354,0.156 10 false R5

U169904E03
0.719,3.188 3.115,3.354 2.396,0.167 10 false Curtain Shield Squib LH 2.052,1.563 2.427,1.75 0.375,0.188 10 false ICL+ 0.188,0.031 1.25,0.344 1.063,0.313 12 false for 3 Door: 4.771,1.656 5.167,1.844 0.396,0.188 10 false ICL+ 2.073,2.385 2.427,2.573 0.354,0.188 10 false ICL- 4.781,2.51 5.177,2.698 0.396,0.188 10 false ICL- 2.458,1.552 2.604,1.719 0.146,0.167 10 false 1 2.479,2.385 2.635,2.542 0.156,0.156 10 false 2 4.583,1.563 4.698,1.729 0.115,0.167 10 false 4 4.583,2.396 4.781,2.563 0.198,0.167 10 false 3 4.76,4.146 5.083,4.333 0.323,0.188 10 false R49 4.75,4.354 6.198,4.563 1.448,0.208 10 false Center Airbag Sensor 0.75,3.01 1.104,3.167 0.354,0.156 10 false R35

CAUTION / NOTICE / HINT

NOTICE:
·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

When disconnecting and reconnecting the battery (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE).

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used (See page General>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART).


·

After replacing the center airbag sensor, refer to initialization (See page General>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE).



HINT:

To perform the simulation method, enter check mode (signal check) with the intelligent tester (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>CHECK MODE PROCEDURE), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


PROCEDURE

1.CHECK VEHICLE TYPE
a.

Check vehicle type.

Result
Result Proceed to
for 3 Door A
for 5 Door B



B

2.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)

A

6.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)
2.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)
a.
E272064C06
0.198,2 0.615,2.229 0.417,0.229 2.01,2.823 2.219,3 false 1.021,0.052 1.333,0.208 0.313,0.156 10 false *1 1.865,1.188 2.177,1.344 0.313,0.156 10 false *2 2.365,1.969 2.677,2.125 0.313,0.156 10 false *3 2.26,2.979 2.573,3.135 0.313,0.156 10 false *4 1.5,1.458 1.813,1.615 0.313,0.156 10 false *a 0.313,2.031 0.74,2.25 0.427,0.219 10 false R5 2,0.229 2.313,0.385 0.313,0.156 10 false A 1.469,0.5 1.792,0.729 0.323,0.229 10 false C 1.25,0.5 1.573,0.729 0.323,0.229 10 false D
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Curtain Shield Squib LH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the curtain shield airbag LH.


d.

Connect the black wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.




OK

NG

3.CHECK CONNECTOR
3.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C385521C01
0.656,0.448 0.969,0.604 0.313,0.156 10 false *1 1.719,1.635 2.031,1.792 0.313,0.156 10 false *2 0.854,0.927 1.01,1.125 0.156,0.198 10 false D 1.094,0.927 1.25,1.125 0.156,0.198 10 false C 1.49,0.938 1.646,1.135 0.156,0.198 10 false B 1.885,0.667 2.042,0.865 0.156,0.198 10 false A
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor


Check that the floor wire connectors (on the curtain shield airbag LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

4.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG LH - CENTER AIRBAG SENSOR)

NG

REPLACE NO. 2 FLOOR WIRE

4.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG LH - CENTER AIRBAG SENSOR)
a.
C314152C07
0.25,2.083 0.667,2.333 0.417,0.25 0.865,2.99 1.344,2.802 true 2.052,3 1.656,2.813 true 1.99,1.427 2.302,1.583 0.313,0.156 10 false *3 1.417,0.25 1.729,0.406 0.313,0.156 10 false *2 2.042,2.396 2.354,2.552 0.313,0.156 10 false *4 1.417,2 1.729,2.156 0.313,0.156 10 false *a 1.042,0.781 1.354,0.938 0.313,0.156 10 false D 1.281,0.792 1.594,0.948 0.313,0.156 10 false C 1.698,0.792 2.01,0.948 0.313,0.156 10 false B 2.104,0.521 2.417,0.677 0.313,0.156 10 false A 0.74,3.01 1.313,3.177 0.573,0.167 10 false ICL+ 2,3.021 2.573,3.188 0.573,0.167 10 false ICL- 0.365,2.125 0.938,2.292 0.573,0.167 10 false R5 0.792,0.25 1.104,0.406 0.313,0.156 10 false *1
*1 Curtain Shield Squib LH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Curtain Shield Squib LH)


Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R5-1 (ICL+) - Body ground Ignition switch ON Below 1 V
R5-2 (ICL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-1 (ICL+) - R5-2 (ICL-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R5-1 (ICL+) - R5-2 (ICL-) Always 1 MΩ or higher
R5-1 (ICL+) - Body ground Always 1 MΩ or higher
R5-2 (ICL-) - Body ground Always 1 MΩ or higher




OK

5.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

5.CHECK CENTER AIRBAG SENSOR
a.
C146259C38
0.896,0.563 0.896,1.417 false 0.813,1.438 1.042,1.594 0.229,0.156 10 *1 1.531,1.354 1.708,1.531 0.177,0.177 10 *2 1.01,0.667 1.146,0.833 0.135,0.167 10 D 1.135,0.656 1.271,0.823 0.135,0.167 10 C
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor


Connect the connectors to the curtain shield airbag LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.




OK

NG

6.CHECK CURTAIN SHIELD AIRBAG LH (CURTAIN SHIELD SQUIB LH)
a.
C385524C01
0.542,1.833 0.875,2.031 0.333,0.198 2.344,2.802 2.052,2.604 false 0.865,0.26 1.177,0.417 0.313,0.156 10 false *1 1.656,1.354 1.969,1.51 0.313,0.156 10 false *2 2.375,1.677 2.688,1.833 0.313,0.156 10 false *3 2.417,2.792 2.729,2.948 0.313,0.156 10 false *4 1.604,1.542 1.917,1.698 0.313,0.156 10 false *a 0.563,1.844 1.021,2.042 0.458,0.198 10 false R35 1.813,0.438 1.969,0.635 0.156,0.198 10 false A 1.292,0.729 1.448,0.927 0.156,0.198 10 false C 1.063,0.719 1.219,0.917 0.156,0.198 10 false D
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor
*3 Connector C
*4 SST
*a Front view of wire harness connector
(to Curtain Shield Squib LH)


Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect the connectors from the curtain shield airbag LH.


d.

Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

CAUTION:

Never connect the tester to the curtain shield airbag LH (curtain shield squib LH) for measurement, as this may lead to a serious injury due to airbag deployment.


NOTICE:
·

Do not forcibly insert SST into the terminals of the connector when connecting SST.

·

Insert SST straight into the terminals of the connector.




SST
09843-18061  

e.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.



h.

Turn the ignition switch off.


i.

Turn the ignition switch to ON, and wait for at least 60 seconds.


j.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.




OK

NG

7.CHECK CONNECTOR
7.CHECK CONNECTOR
a.

Turn the ignition switch off.


b.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


c.

Disconnect SST from connector C.


d.
C208249C39
0.854,0.948 1.052,1.188 0.198,0.24 10 false D 0.646,0.458 0.844,0.625 0.198,0.167 10 false *1 1.75,1.667 1.948,1.833 0.198,0.167 10 false *2 1.083,0.948 1.292,1.167 0.208,0.219 10 false C 1.5,0.948 1.708,1.177 0.208,0.229 10 false B 1.906,0.646 2.104,0.833 0.198,0.188 10 false A
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor


Check that the floor wire connectors (on the curtain shield airbag LH side) are not damaged.

OK:

The lock button is not disengaged, and the claw of the lock is not deformed or damaged.




OK

8.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG LH - CENTER AIRBAG SENSOR)

NG

REPLACE NO. 2 FLOOR WIRE

8.CHECK NO. 2 FLOOR WIRE (CURTAIN SHIELD AIRBAG LH - CENTER AIRBAG SENSOR)
a.
C385403C01
0.969,0.49 0.969,0.156 0.969,0.156 1.073,0.156 false 1.479,0.479 1.479,0.146 1.479,0.146 1.583,0.146 false 1.115,2.635 1.542,2.385 true 2.24,2.625 1.76,2.385 true 1.083,0.042 1.396,0.198 0.313,0.156 10 false *1 1.635,0.042 1.948,0.198 0.313,0.156 10 false *2 1.906,1.365 2.219,1.521 0.313,0.156 10 false *3 2.365,2.156 2.677,2.313 0.313,0.156 10 false *4 1.563,1.771 1.875,1.927 0.313,0.156 10 false *a 0.521,2.01 0.979,2.208 0.458,0.198 10 false R35 0.865,2.656 1.323,2.854 0.458,0.198 10 false ICL+ 2.156,2.656 2.615,2.854 0.458,0.198 10 false ICL- 2.042,0.479 2.25,0.667 0.208,0.188 10 false A 1.688,0.719 1.896,0.906 0.208,0.188 10 false B 1.281,0.708 1.49,0.896 0.208,0.188 10 false C 1.052,0.708 1.26,0.896 0.208,0.188 10 false D
*1 Curtain Shield Squib LH
*2 No. 2 Floor Wire
*3 Center Airbag Sensor
*4 Connector C
*a Front view of wire harness connector
(to Curtain Shield Squib LH)


Disconnect the connectors from the center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
R35-1 (ICL+) - Body ground Ignition switch ON Below 1 V
R35-2 (ICL-) - Body ground Ignition switch ON Below 1 V



d.

Turn the ignition switch off.


e.

Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R35-1 (ICL+) - R35-2 (ICL-) Always Below 1 Ω



g.

Release the activation prevention mechanism built into connector B (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DIAGNOSIS SYSTEM).


h.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
R35-1 (ICL+) - R35-2 (ICL-) Always 1 MΩ or higher
R35-1 (ICL+) - Body ground Always 1 MΩ or higher
R35-2 (ICL-) - Body ground Always 1 MΩ or higher




OK

9.CHECK CENTER AIRBAG SENSOR

NG

REPLACE NO. 2 FLOOR WIRE

9.CHECK CENTER AIRBAG SENSOR
a.
C146259C39
0.76,0.229 0.99,0.385 0.229,0.156 10 false *1 1.906,1.313 2.083,1.49 0.177,0.177 10 false *2 1.01,0.667 1.146,0.833 0.135,0.167 10 false D 1.135,0.656 1.271,0.823 0.135,0.167 10 false C
*1 Curtain Shield Squib LH
*2 Center Airbag Sensor


Connect the connectors to the curtain shield airbag LH and center airbag sensor.


b.

Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


c.

Turn the ignition switch to ON, and wait for at least 60 seconds.



e.

Turn the ignition switch off.


f.

Turn the ignition switch to ON, and wait for at least 60 seconds.


g.

Check for DTCs (See page Vehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>DTC CHECK / CLEAR).

OK:

DTC B1835, B1836, B1837 or B1838 is not output.


HINT:

Codes other than DTC B1835, B1836, B1837 and B1838 may be output at this time, but they are not related to this check.




OK

NG