Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Any of the following conditions are met:
·

"Combination Meter" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Combination meter assembly main wire or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C448182E01
5.656,0.896 6.146,1.104 0.49,0.208 10 false CANH 5.677,1.677 6.156,1.885 0.479,0.208 10 false CANL 5.656,2.375 6.135,2.625 0.479,0.25 10 false B 5.635,3.104 6.115,3.313 0.479,0.208 10 false IG+ 5.646,4.24 6.125,4.448 0.479,0.208 10 false E2 5.385,0.875 5.708,1.073 0.323,0.198 10 false 40 5.385,1.406 5.667,1.604 0.281,0.198 10 false 39 5.375,2.24 5.688,2.427 0.313,0.188 10 false 21 5.385,2.99 5.667,3.188 0.281,0.198 10 false 22 5.375,4.146 5.781,4.344 0.406,0.198 10 false 20 1.552,0.896 1.708,1.094 0.156,0.198 10 false 8 1.531,1.396 1.813,1.594 0.281,0.198 10 false 18 0.24,1.875 0.698,2.073 0.458,0.198 10 false G286 0.24,2.031 3.146,2.229 2.906,0.198 10 false No. 2 CAN Junction Connector 4.135,2.219 5.063,2.479 0.927,0.26 10 false ECU-B 4.094,2.969 5.01,3.208 0.917,0.24 10 false METER 2.271,2.365 3.156,2.656 0.885,0.292 10 false from Battery 1.99,3.125 3.344,3.438 1.354,0.313 10 false from IG2 Relay*1 5.135,4.813 5.594,5.01 0.458,0.198 10 false G304 5.135,4.979 7.125,5.302 1.99,0.323 10 false Combination Meter Assembly 0.938,3.635 3.542,3.969 2.604,0.333 10 false from Engine Stop and Start ECU*2 0.458,4.667 3.063,5 2.604,0.333 10 false *1: w/o Stop and Start System 0.469,5.125 3.073,5.458 2.604,0.333 10 false *2: w/ Stop and Start System

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369139C10
1.5,0.75 1.917,1 0.417,0.25 2.927,1.958 2.74,2.583 2.74,2.583 2.573,2.583 true 2.792,1.938 2.635,2.354 2.635,2.354 2.469,2.354 true 1.542,0.792 1.979,0.99 0.438,0.198 10 false G304 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 2.083,2.26 2.583,2.448 0.5,0.188 10 false CANL 2.167,2.5 2.667,2.688 0.5,0.188 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G304-40 (CANH) - G304-39 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Result Proceed to
OK (w/o Stop and Start System) A
OK (w/ Stop and Start System) B
NG C


A

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

B

3.CHECK HARNESS AND CONNECTOR

C

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369139C26
1.5,0.75 1.917,1 0.417,0.25 0.917,2.333 0.75,2.333 0.75,2.333 0.656,1.938 true 0.833,2.531 0.667,2.531 0.667,2.531 0.5,1.938 true 2.948,1.729 2.844,0.896 2.844,0.896 2.677,0.896 true 1.542,0.792 1.979,0.99 0.438,0.198 10 false G304 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 0.958,2.24 1.458,2.427 0.5,0.188 10 false IG+ 0.896,2.448 1.396,2.635 0.5,0.188 10 false B 2.417,0.823 2.771,1.01 0.354,0.188 10 false E2
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G304-20 (E2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G304-21 (B) - Body ground Always 11 to 14 V
G304-22 (IG+) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

3.CHECK HARNESS AND CONNECTOR
a.
C369139C26
1.5,0.75 1.917,1 0.417,0.25 0.917,2.333 0.75,2.333 0.75,2.333 0.656,1.938 true 0.833,2.531 0.667,2.531 0.667,2.531 0.5,1.938 true 2.948,1.729 2.844,0.896 2.844,0.896 2.677,0.896 true 1.542,0.792 1.979,0.99 0.438,0.198 10 false G304 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 0.958,2.24 1.458,2.427 0.5,0.188 10 false IG+ 0.896,2.448 1.396,2.635 0.5,0.188 10 false B 2.417,0.823 2.771,1.01 0.354,0.188 10 false E2
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G304-20 (E2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G304-21 (B) - Body ground Always 11 to 14 V
G304-22 (IG+) - Body ground Ignition switch ON 10.5 to 16 V
Ignition switch off Below 1 V



Result:
Result Proceed to
OK A
NG (IG+ terminal) B
NG (Other terminal) C


A

REPLACE COMBINATION METER ASSEMBLY

B

C

REPAIR OR REPLACE HARNESS OR CONNECTOR