Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  U0199  Lost Communication with "Door Control Module A"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U0200 Lost Communication with "Door Control Module B" There is no communication from the outer mirror control ECU assembly RH.
·

Power source circuit of outer mirror control ECU assembly RH

·

Outer mirror control ECU assembly RH ground circuit

·

Outer mirror control ECU assembly RH CAN branch wire or connector

·

Outer mirror control ECU assembly RH


Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C306900E27
5.594,0.469 6.167,0.656 0.573,0.188 10 false CANP 5.604,1 6.229,1.198 0.625,0.198 10 false CANN 5.625,1.896 6.219,2.146 0.594,0.25 10 false CPUB 5.604,2.417 6.229,2.615 0.625,0.198 10 false BDR 5.604,2.927 6.167,3.188 0.563,0.26 10 false SIG 5.594,3.438 6.146,3.688 0.552,0.25 10 false GND 4.656,4.167 5.031,4.365 0.375,0.198 10 false J12 4.646,4.333 7.146,4.698 2.5,0.365 10 false Outer Mirror Control ECU Assembly RH 0.146,1.313 0.51,1.521 0.365,0.208 10 false G288 0.135,1.521 2.323,1.74 2.188,0.219 10 false No. 4 CAN Junction Connector 1.677,0.323 1.896,0.531 0.219,0.208 10 false 1 1.667,0.875 1.948,1.073 0.281,0.198 10 false 12 5.344,0.333 5.531,0.552 0.188,0.219 10 false 9 5.344,0.875 5.563,1.125 0.219,0.25 10 false 8 5.365,1.781 5.604,2.01 0.24,0.229 10 false 6 5.302,2.292 5.583,2.51 0.281,0.219 10 false 14 5.365,2.823 5.615,3.073 0.25,0.25 10 false 5 5.365,3.344 5.604,3.583 0.24,0.24 10 false 7 2.156,1.854 3.302,2.188 1.146,0.333 10 false from Battery 2.156,2.385 3.208,2.698 1.052,0.313 10 false from Battery 1.74,2.885 3.24,3.156 1.5,0.271 10 false from IG NO.1 Relay 3.969,1.729 4.906,2 0.938,0.271 10 false ECU-B 3.521,2.219 4.99,2.448 1.469,0.229 10 false DOOR D*1, DOOR P*2 3.813,2.75 4.823,2.979 1.01,0.229 10 false ECU-IG NO.2 0.24,3.708 1.708,3.938 1.469,0.229 10 false *1: for RHD 0.24,4.063 1.708,4.292 1.469,0.229 10 false *2: for LHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Check for DTCs.

HINT:

If DTC U1002 is output from the gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) A
DTC U1002 is output from main body ECU (multiplex network body ECU) B



A

2.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY RH BRANCH WIRE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (OUTER MIRROR CONTROL ECU ASSEMBLY RH BRANCH WIRE)
a.
C300894C30
0.271,0.927 0.677,1.219 0.406,0.292 0.823,1.823 0.969,1.823 0.969,1.823 1.271,1.281 true 1.781,1.854 1.635,1.854 1.635,1.854 1.448,1.271 true 0.115,0.125 0.469,0.333 0.354,0.208 10 false *a 0.365,0.99 0.74,1.292 0.375,0.302 10 false J12 1.865,1.792 2.469,2.042 0.604,0.25 10 false CANP 0.417,1.76 0.948,1.979 0.531,0.219 10 false CANN
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Disconnect the cable from the negative (-) battery terminal.


b.

Disconnect the outer mirror control ECU assembly RH connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J12-9 (CANP) - J12-8 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C300894C31
0.271,0.927 0.677,1.219 0.406,0.292 1.396,1.656 1.542,1.656 1.542,1.656 1.844,1.115 true 2.521,1.844 2.375,1.844 2.375,1.844 2.188,1.26 true 2.594,0.635 2.448,0.635 2.448,0.635 2.219,0.927 true 1.417,2.021 1.563,2.021 1.563,2.021 1.99,1.115 true 0.115,0.125 0.469,0.375 0.354,0.25 10 false *a 0.365,1 0.719,1.24 0.354,0.24 10 false J12 2.656,0.552 3.188,0.74 0.531,0.188 10 false GND 1.031,1.958 1.656,2.135 0.625,0.177 10 false CPUB 2.583,1.792 3.125,2 0.542,0.208 10 false BDR 1.156,1.583 1.656,1.771 0.5,0.188 10 false SIG
*a Front view of wire harness connector
(to Outer Mirror Control ECU Assembly RH)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
J12-7 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
J12-5 (SIG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
J12-6 (CPUB) - Body ground Always 11 to 14 V
J12-14 (BDR) - Body ground Always 11 to 14 V



Result:
Proceed to
OK
NG



OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY RH

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)