Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) C

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  U0208  Lost Communication with "Seat Control Module A"  


DESCRIPTION

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
U0208 Lost Communication with ''Seat Control Module A'' There is no communication from the front power seat switch (power seat control ECU).
·

Front power seat switch (power seat control ECU) CAN branch wire or connector

·

Front power seat switch (power seat control ECU)

·

Front power seat switch (power seat control ECU) ground circuit

·

Power source or inside front power seat switch (power seat control ECU)


Main body ECU (multiplex network body ECU)

WIRING DIAGRAM

C384286E01
0.281,1.771 0.896,1.969 0.615,0.198 10 false G288 0.281,1.958 2.417,2.375 2.135,0.417 10 false No. 4 CAN Junction Connector 2.219,2.229 3.396,2.49 1.177,0.26 10 false from Battery 2.219,2.729 3.396,2.99 1.177,0.26 10 false from Battery 4.792,3.885 6.542,4.677 1.75,0.792 10 false Front Power Seat Switch (Power Seat Control ECU) 5.271,1.052 5.885,1.25 0.615,0.198 10 false CANP 5.271,1.5 5.885,1.698 0.615,0.198 10 false CANN 5.271,2.25 5.885,2.448 0.615,0.198 10 false +B 5.271,2.74 5.885,2.938 0.615,0.198 10 false SYSB 5.271,3.24 5.885,3.438 0.615,0.198 10 false GND 3.833,2.604 4.583,2.813 0.75,0.208 10 false ECU-B 3.552,1.875 4.594,2.25 1.042,0.375 10 false P/ SEAT F/L*1, P/ SEAT F/R*2 0.229,4.344 1.406,4.635 1.177,0.292 10 false *2: for RHD 0.229,4.052 1.417,4.344 1.188,0.292 10 false *1: for LHD 1.958,1.385 2.271,1.583 0.313,0.198 10 false 13 1.958,0.938 2.271,1.135 0.313,0.198 10 false 2 4.698,0.906 5.094,1.125 0.396,0.219 10 false 8*1 4.729,1.063 4.99,1.25 0.26,0.188 10 false b5 5.01,1.063 5.271,1.25 0.26,0.188 10 false a5 4.99,0.906 5.385,1.125 0.396,0.219 10 false 8*2 4.729,1.5 4.99,1.688 0.26,0.188 10 false b5 5,1.5 5.26,1.688 0.26,0.188 10 false a5 4.729,2.26 4.99,2.448 0.26,0.188 10 false b4 5.01,2.26 5.271,2.448 0.26,0.188 10 false a4 4.729,2.74 4.99,2.927 0.26,0.188 10 false b5 5,2.74 5.26,2.927 0.26,0.188 10 false a5 4.729,3.25 4.99,3.438 0.26,0.188 10 false b4 5.01,3.25 5.271,3.438 0.26,0.188 10 false a4 4.708,1.344 5.104,1.563 0.396,0.219 10 false 7*1 4.979,1.344 5.375,1.563 0.396,0.219 10 false 7*2 4.708,2.083 5.104,2.302 0.396,0.219 10 false 7*1 4.99,2.083 5.385,2.302 0.396,0.219 10 false 7*2 4.615,2.573 5.021,2.781 0.406,0.208 10 false 12*1 4.927,2.573 5.333,2.781 0.406,0.208 10 false 12*2 4.677,3.073 5.073,3.292 0.396,0.219 10 false 2*1 4.969,3.073 5.365,3.292 0.396,0.219 10 false 2*2

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

·

When disconnecting and reconnecting the battery.

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.RECONFIRM DTC OUTPUT
a.

Check for DTCs.

HINT:

If DTC U1002 is output from the gateway of the main body ECU (multiplex network body ECU), this indicates a sub bus 1 malfunction. Troubleshoot for DTC U1002 and check for malfunctions in sub bus 1.



Result:
Result Proceed to
DTC U1002 is not output from main body ECU (multiplex network body ECU) A
DTC U1002 is output from main body ECU (multiplex network body ECU) B


A

2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH [POWER SEAT CONTROL ECU] BRANCH WIRE)

B

GO TO DIAGNOSIS PROCEDURE INDICATED BY OUTPUT DTC

2.CHECK FOR OPEN IN CAN BUS WIRE (FRONT POWER SEAT SWITCH [POWER SEAT CONTROL ECU] BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C380943C02
0.198,0.635 0.563,0.875 0.365,0.24 0.198,0.979 0.563,1.219 0.365,0.24 1.146,1.927 1.344,1.927 1.344,1.927 1.344,1.458 true 1.729,1.927 1.51,1.927 1.51,1.927 1.51,1.458 true 0.104,0.073 0.417,0.271 0.313,0.198 10 false *a 0.323,0.677 0.635,0.875 0.313,0.198 10 false a5 1.771,1.823 2.385,2.021 0.615,0.198 10 false CANP 0.708,1.844 1.323,2.042 0.615,0.198 10 false CANN 0.625,0.677 0.938,0.875 0.313,0.198 10 false *A 0.323,1.042 0.635,1.24 0.313,0.198 10 false b5 0.635,1.031 0.948,1.229 0.313,0.198 10 false *B
*A for RHD
*B for LHD
*a Front view of wire harness connector
(to Front Power Seat Switch [Power Seat Control ECU])


Disconnect the front power seat switch (power seat control ECU) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
a5-8 (CANP) - a5-7 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω

for LHD
Tester Connection Condition Specified Condition
b5-8 (CANP) - b5-7 (CANN) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.

Disconnect the front power seat switch (power seat control ECU) connector.


b.
C285280C74
0.198,0.677 0.604,0.927 0.406,0.25 0.292,2.198 0.677,2.49 0.385,0.292 0.198,1.01 0.604,1.26 0.406,0.25 0.292,2.583 0.677,2.875 0.385,0.292 1,1.667 1.135,1.667 1.135,1.667 1.385,2.24 true 2.479,1.51 2.354,1.51 2.354,1.51 2.125,1.188 true 1.719,3.042 1.594,3.042 1.594,3.042 1.406,2.542 true 0.333,0.729 0.792,0.927 0.458,0.198 10 false b5 0.417,2.26 0.875,2.458 0.458,0.198 10 false b4 0.094,0.083 0.406,0.281 0.313,0.198 10 false *a 0.635,1.594 1.229,1.865 0.594,0.271 10 false GND 2.531,1.417 3.146,1.615 0.615,0.198 10 false SYSB 1.76,2.979 2.073,3.177 0.313,0.198 10 false +B 0.646,0.719 1.104,0.917 0.458,0.198 10 false *A 0.344,1.063 0.802,1.26 0.458,0.198 10 false a5 0.667,1.063 1.125,1.26 0.458,0.198 10 false *B 0.729,2.25 1.188,2.448 0.458,0.198 10 false *A 0.417,2.646 0.875,2.844 0.458,0.198 10 false a4 0.729,2.646 1.188,2.844 0.458,0.198 10 false *B
*A for LHD
*B for RHD
*a Front view of wire harness connector
(to Front Power Seat Switch [Power Seat Control ECU])


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
a4-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
b4-2 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



c.

Reconnect the cable to the negative (-) battery terminal.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
for RHD
Tester Connection Condition Specified Condition
a4-7 (+B) - Body ground Always 11 to 14 V
a5-12 (SYSB) - Body ground Always 11 to 14 V

for LHD
Tester Connection Condition Specified Condition
b4-7 (+B) - Body ground Always 11 to 14 V
b5-12 (SYSB) - Body ground Always 11 to 14 V




OK

REPLACE FRONT POWER SEAT SWITCH (POWER SEAT CONTROL ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)