| Detection Item | Symptom | Trouble Area |
|---|---|---|
| Clearance Warning ECU Communication Stop Mode | Any of the following conditions are met:
·
|
·
Clearance warning ECU assembly branch wire or connector ·
Power source circuit of clearance warning ECU assembly ·
Clearance warning ECU assembly ground circuit ·
Clearance warning ECU assembly |
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery.
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
Inspect the fuses for circuits related to this system before performing the following procedure.
DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Disconnect the cable from the negative (-) battery terminal.
| *A | for 8 Sensor Type |
| *B | for 4 Sensor Type |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Disconnect the clearance warning ECU assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G228-17 (R1) - G228-18 (R2) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-17 (R1) - I9-18 (R2) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Result | Proceed to |
|---|---|
| OK (for 8 Sensor Type or for 4 Sensor Type without Stop and Start System) | A |
| OK (for 4 Sensor Type with Stop and Start System) | B |
| NG | C |
A
B
C
| *A | for 8 Sensor Type |
| *B | for 4 Sensor Type |
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G228-30 (E) - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-30 (E) - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| G228-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I9-1 (IG) - Body ground | Ignition switch ON | 11 to 14 V |
| Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL
NG
| *a | Front view of wire harness connector
(to Clearance Warning ECU Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| I9-30 (E) - Body ground | Cable disconnected from negative (-) battery terminal | Below 1 Ω |
Reconnect the cable to the negative (-) battery terminal.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| I9-1 (IG) - Body ground | Ignition switch ON | 10.5 to 16 V |
| Ignition switch off | Below 1 V |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (IG terminal) | B |
| NG (Other terminal) | C |
A
for LHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for LHD)>REMOVAL
for RHD: Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>CLEARANCE WARNING ECU (for RHD)>REMOVAL
B
Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>HOW TO PROCEED WITH TROUBLESHOOTING
C