Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Suspension Control ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Suspension Control ECU Communication Stop Mode Any of the following conditions are met:
·

"Suspension Control (Air Suspension)" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Suspension Control ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Suspension control ECU CAN branch wire or connector

·

Power source circuit of suspension control ECU

·

Suspension control ECU ground circuit

·

Suspension control ECU



WIRING DIAGRAM

C382913E02
0.167,1.646 2.25,1.896 2.083,0.25 10 false No. 1 CAN Junction Connector 0.177,1.448 0.792,1.646 0.615,0.198 10 false A121 1.698,0.552 2.313,0.75 0.615,0.198 10 false 1 1.698,1.146 2.313,1.344 0.615,0.198 10 false 7 5.302,0.458 5.917,0.656 0.615,0.198 10 false 7 5.313,1.052 5.927,1.25 0.615,0.198 10 false 8 5.302,1.74 5.917,1.938 0.615,0.198 10 false 1 5.313,2.531 5.927,2.729 0.615,0.198 10 false 3 5.313,3.125 5.927,3.323 0.615,0.198 10 false 5 5.26,3.625 5.875,3.823 0.615,0.198 10 false 10 5.625,0.688 6.24,0.885 0.615,0.198 10 false CANH 5.615,1.927 6.229,2.125 0.615,0.198 10 false IG 5.615,2.729 6.229,2.927 0.615,0.198 10 false B 5.615,3.323 6.229,3.521 0.615,0.198 10 false GND 5.625,3.844 6.24,4.042 0.615,0.198 10 false GND 4.313,1.802 4.927,2 0.615,0.198 10 false AVS 3.99,2.594 4.979,2.781 0.99,0.188 10 false AIR SUS NO.2 2.573,2.74 3.563,2.927 0.99,0.188 10 false from Battery 2.146,1.938 3.573,2.229 1.427,0.292 10 false from IG NO.3 Relay 5.625,1.271 6.24,1.469 0.615,0.198 10 false CANL 5.208,4.26 6.927,4.51 1.719,0.25 10 false Suspension Control ECU 5.219,0.677 5.833,0.875 0.615,0.198 10 false A49 5.219,1.26 5.833,1.458 0.615,0.198 10 false A49 5.219,1.948 5.833,2.146 0.615,0.198 10 false A49 5.219,2.74 5.833,2.938 0.615,0.198 10 false A49 5.219,3.313 5.833,3.51 0.615,0.198 10 false A49 5.219,3.833 5.833,4.031 0.615,0.198 10 false R19

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (SUSPENSION CONTROL ECU BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C379586C04
1.406,0.281 1.854,0.521 0.448,0.24 0.531,2.917 0.698,2.917 0.698,2.917 0.865,2 true 1.333,2.927 1.125,2.927 1.125,2.927 1.021,2.01 true 0.063,0.052 0.375,0.25 0.313,0.198 10 false *a 0.104,2.833 0.635,3.031 0.531,0.198 10 false CANH 1.396,2.833 1.927,3.031 0.531,0.198 10 false CANL 1.51,0.333 2.042,0.531 0.531,0.198 10 false A49
*a Front view of wire harness connector
(to Suspension Control ECU)


Disconnect the suspension control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-7 (CANH) - A49-8 (CANL) Cable disconnected from negative (-) battery terminal 54 to 69 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C382914C02
1.5,0.333 1.917,0.583 0.417,0.25 1.5,2.417 1.917,2.667 0.417,0.25 2.5,3.271 2.75,2.75 2.75,2.75 2.917,2.75 true 2.219,1.198 2.729,0.646 2.729,0.646 2.896,0.646 true 0.979,0.5 1.146,0.5 1.146,0.5 1.5,1.188 true 0.479,0.771 0.646,0.771 0.646,0.771 1.01,1.198 true 1.594,0.385 2.052,0.583 0.458,0.198 10 false A49 1.594,2.469 2.052,2.667 0.458,0.198 10 false R19 2.979,2.688 3.333,2.865 0.354,0.177 10 false GND 2.969,0.573 3.323,0.75 0.354,0.177 10 false GND 0.823,0.427 1.177,0.604 0.354,0.177 10 false B 0.271,0.708 0.625,0.885 0.354,0.177 10 false IG 0.135,0.063 0.49,0.24 0.354,0.177 10 false *a
*a Front view of wire harness connector
(to Suspension Control ECU)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A49-5 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω
R19-10 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A49-1 (IG) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V
A49-3 (B) - Body ground Always 11 to 14 V




OK

REPLACE SUSPENSION CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)