There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
| Symptom | Trouble Area |
|---|---|
|
*1: w/ Entry and Start System *2: for 1GR-FE, 1GD-FTV, 2TR-FE with Pre-collision System *3: for 2TR-FE without Pre-collision System *4: w/ Tire Pressure Warning System *5: for LED Headlight *6: w/ Urea SCR System *7: w/ Stop and Start System |
|
| Resistance between terminals 18 (CA4H) and 17 (CA4L) of the central gateway ECU (network gateway ECU) is below 54 Ω. | ·
Short in CAN main bus wire ·
Short in CAN branch wire ·
Central gateway ECU (network gateway ECU) ·
ECM ·
Air conditioning amplifier assembly ·
Urea pump control ECU*6 ·
Certification ECU (smart key ECU assembly)*1 ·
Power steering ECU assembly ·
Master cylinder solenoid (skid control ECU)*2 ·
Brake actuator assembly (skid control ECU)*3 ·
Airbag sensor assembly ·
Steering sensor ·
Combination meter assembly ·
Tire pressure warning ECU and receiver*4 ·
Main body ECU (multiplex network body ECU) ·
Engine stop and start ECU*7 ·
No. 1 headlight ECU sub-assembly LH*5 ·
No. 2 CAN junction connector ·
No. 6 CAN junction connector |
for LHD
for RHD
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART
Some parts must be initialized and set when replacing or removing and installing parts.
Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE
After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Before replacing the certification ECU (smart key ECU assembly), refer to Service Bulletin.
Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.
When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.
Disconnect the cable from the negative (-) battery terminal.
Disconnect the No. 6 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 6 CAN Junction Connector) |
*b | to No. 2 CAN Junction Connector |
| *c | ·
to Airbag Sensor Assembly (for LHD) ·
to Urea Pump Control ECU (for RHD with Urea SCR System) |
*d | to Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) |
| *e | to No. 1 Headlight ECU Sub-assembly LH (for RHD with LED Headlight) | *f | to Tire Pressure Warning ECU and Receiver (for RHD with Tire Pressure Warning System) |
| *g | to Central Gateway ECU (Network Gateway ECU) | *h | to Air Conditioning Amplifier Assembly |
| *i | to Power Steering ECU Assembly (for LHD) | *j | to Steering Sensor (for LHD) |
| *k | to ECM | - | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: w/ Entry and Start System *2: for RHD with LED Headlight *3: for RHD with Tire Pressure Warning System *4: for LHD *5: for RHD with Urea SCR System |
|||
| G290-1 (CANH) - G290-11 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 2 CAN junction connector |
| G290-2 (CANH) - G290-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
Airbag sensor assembly*4 ·
Urea pump control ECU*5 |
| G290-3 (CANH) - G290-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Certification ECU (smart key ECU assembly)*1 |
| G290-4 (CANH) - G290-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 1 headlight ECU sub-assembly LH*2 |
| G290-5 (CANH) - G290-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Tire pressure warning ECU and receiver*3 |
| G290-6 (CANH) - G290-16 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Central gateway ECU (network gateway ECU) |
| G290-7 (CANH) - G290-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Air conditioning amplifier assembly |
| G290-8 (CANH) - G290-18 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Power steering ECU assembly*4 |
| G290-9 (CANH) - G290-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Steering sensor*4 |
| G290-10 (CANH) - G290-20 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | ECM |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Central gateway ECU [network gateway ECU] CAN branch wire) | B |
| NG (ECM CAN main wire) | C |
| NG (No. 2 CAN junction connector CAN main wire) | D |
| NG (Wire to ECU or sensor) | E |
A
B
C
D
E
Reconnect the G290 No. 6 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Central Gateway ECU [Network Gateway ECU]) |
Disconnect the central gateway ECU (network gateway ECU) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-18 (CA4H) - G229-17 (CA4L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the G290 No. 6 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the ECM connector.
| *A | for 1GR-FE | *B | for Manual Transmission |
| *C | for Automatic Transmission | *D | for 1GD-FTV |
| *E | for 2TR-FE | - | - |
| *a | Front view of wire harness connector
(to ECM) |
- | - |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-32 (CANH) - G56-31 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G56-31 (CANH) - G56-25 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G181-13 (CANH) - G181-14 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G184-17 (CANH) - G184-28 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
for 1GR-FE: Click hereEngine / Hybrid System>1GR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 2TR-FE: Click hereEngine / Hybrid System>2TR-FE (ENGINE CONTROL)>ECM>REMOVAL
for 1GD-FTV: Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
NG
Reconnect the G290 No. 6 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the No. 2 CAN junction connector.
| *a | Front view of wire harness connector
(to No. 2 CAN Junction Connector) |
*b | to No. 6 CAN Junction Connector |
| *c | ·
to Urea Pump Control ECU (for LHD with Urea SCR System) ·
to Steering Sensor (for RHD) |
*d | to Airbag Sensor Assembly (for RHD) |
| *e | to No. 1 Headlight ECU Sub-assembly LH (for LHD with LED Headlight) | *f | to Engine Stop and Start ECU (w/ Stop and Start System) |
| *g | ·
to Tire Pressure Warning ECU and Receiver (for LHD with Tire Pressure Warning System) ·
to Power Steering ECU Assembly (for RHD) |
*h | to Combination Meter Assembly |
| *i | to Main Body ECU (Multiplex Network Body ECU) | *j | ·
to Master Cylinder Solenoid (Skid Control ECU) (for 1GR-FE, 1GD-FTV, 2TR-FE with Pre-collision System) ·
to Brake Actuator Assembly (Skid Control ECU) (for 2TR-FE without Pre-collision System) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Connected to |
|---|---|---|---|
|
*1: for LHD with LED Headlight *2: for LHD with Tire Pressure Warning System *3: for LHD with Pre-collision System *4: for RHD *5: for 1GR-FE, 1GD-FTV, 2TR-FE with Pre-collision System *6: for 2TR-FE without Pre-collision System *7: w/ Stop and Start System |
|||
| G286-1 (CANH) - G286-11 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | No. 6 CAN junction connector |
| G286-2 (CANH) - G286-12 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
Urea pump control ECU*3 ·
Steering sensor*4 |
| G286-3 (CANH) - G286-13 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Airbag sensor assembly*4 |
| G286-4 (CANH) - G286-14 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | No. 1 headlight ECU sub-assembly LH*1 |
| G286-5 (CANH) - G286-15 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Engine stop and start ECU*7 |
| G286-7 (CANH) - G286-17 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
Tire pressure warning ECU and receiver*2 ·
Power steering ECU assembly*4 |
| G286-8 (CANH) - G286-18 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω | Combination meter assembly |
| G286-9 (CANH) - G286-19 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Main body ECU (multiplex network body ECU) |
| G286-10 (CANH) - G286-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | ·
Master cylinder solenoid (skid control ECU)*5 ·
Brake actuator assembly (skid control ECU)*6 |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (Combination meter assembly CAN main wire) | B |
| NG (No. 6 CAN junction connector CAN main wire) | C |
| NG (Wire to ECU or sensor) | D |
A
B
C
D
Reconnect the G286 No. 2 CAN junction connector.
| Proceed to |
|---|
| NEXT |
NEXT
| *a | Front view of wire harness connector
(to Combination Meter Assembly) |
Disconnect the combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G304-40 (CANH) - G304-39 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Central Gateway ECU [Network Gateway ECU]) |
Reconnect the wire harness connectors.
Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited branch line is connected.
Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>TERMINALS OF ECU
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| G229-18 (CA4H) - G229-17 (CA4L) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
| Proceed to |
|---|
| OK |
| NG |
OK
NG