Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325854 CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/ Central Gateway ECU)  Front Camera Module Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Front Camera Module Communication Stop Mode Any of the following conditions are met:
·

"Front Camera Module" is indicated on the "Communication Bus Check" screen of the GTS.

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Front Camera Module Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Forward recognition camera CAN branch wire or connector

·

Power source circuit of forward recognition camera

·

Forward recognition camera ground circuit

·

Forward recognition camera



WIRING DIAGRAM

C369915E05
0.063,1.583 1.427,1.802 1.365,0.219 10 false G287*1, G291*2 1.667,0.531 2.292,0.823 0.625,0.292 10 false 3*1, 5*2 1.646,1.083 2.427,1.365 0.781,0.281 10 false 13*1, 15*2 5.563,0.542 5.813,0.75 0.25,0.208 10 false 5 5.521,1.073 5.771,1.281 0.25,0.208 10 false 11 5.823,0.635 6.5,0.844 0.677,0.208 10 false CA1P 5.813,1.177 6.49,1.385 0.677,0.208 10 false CA1N 5.823,2.24 6.5,2.448 0.677,0.208 10 false IGB 5.813,3.115 6.49,3.323 0.677,0.208 10 false GND 4.208,2.073 5.344,2.281 1.135,0.208 10 false ECU-IG NO.1 2.344,2.25 3.771,2.667 1.427,0.417 10 false from IG NO.1 Relay 5.271,3.458 5.948,3.667 0.677,0.208 10 false W22 5.281,3.615 7.146,3.865 1.865,0.25 10 false Forward Recognition Camera 5.594,2.146 5.844,2.354 0.25,0.208 10 false 7 5.521,3.01 5.771,3.219 0.25,0.208 10 false 10 0.073,1.76 2.115,2.708 2.042,0.948 10 false No. 3 CAN Junction Connector*1, No. 7 CAN Junction Connector*2 0.135,4.031 1.563,4.448 1.427,0.417 10 false *1: for LHD 0.135,4.396 1.573,4.729 1.438,0.333 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/ Central Gateway ECU)>DIAGNOSIS SYSTEM



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (FORWARD RECOGNITION CAMERA BRANCH WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C346989C81
1.51,0.146 1.917,0.375 0.406,0.229 1.979,1.177 2.281,0.448 true 1.938,1.521 2.208,1.927 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.573,0.177 1.948,0.375 0.375,0.198 10 false W22 2.354,0.354 2.792,0.5 0.438,0.146 10 false CA1P 2.292,1.875 2.729,2.021 0.438,0.146 10 false CA1N
*a Front view of wire harness connector
(to Forward Recognition Camera)


Disconnect the forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-5 (CA1P) - W22-11 (CA1N) Cable disconnected from negative (-) battery terminal 54 to 69 Ω



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS BRANCH WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C346989C82
1.51,0.146 1.906,0.385 0.396,0.24 1.104,1.99 1.302,1.531 true 1.99,1.979 1.802,1.521 true 0.094,0.073 0.406,0.229 0.313,0.156 10 false *a 1.563,0.188 1.948,0.375 0.385,0.188 10 false W22 2.063,1.917 2.5,2.063 0.438,0.146 10 false GND 0.792,1.938 1.083,2.104 0.292,0.167 10 false IGB
*a Front view of wire harness connector
(to Forward Recognition Camera)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
W22-10 (GND) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
W22-7 (IGB) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)