Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325853 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Combination Meter ECU Communication Stop Mode  


DESCRIPTION

Detection Item Symptom Trouble Area
Combination Meter ECU Communication Stop Mode Either condition is met:
·

"Combination Meter" is not displayed on "CAN Bus Check".

Click here(Click here)

·

Communication system DTCs (DTCs that start with U) that are output correspond to "Combination Meter ECU Communication Stop Mode" in "DTC Combination Table"

Click here(Click here)


·

Combination meter assembly main wire or connector

·

Power source circuit of combination meter assembly

·

Combination meter assembly ground circuit

·

Combination meter assembly



WIRING DIAGRAM

C382924E01
5.354,2.24 5.969,2.438 0.615,0.198 10 false 26 5.635,0.865 6.25,1.063 0.615,0.198 10 false CANH 5.656,1.656 6.271,1.854 0.615,0.198 10 false CANL 5.323,1.448 5.938,1.646 0.615,0.198 10 false 39 5.323,0.896 5.938,1.094 0.615,0.198 10 false 40 5.354,3.021 5.969,3.219 0.615,0.198 10 false 28 5.344,3.833 5.958,4.031 0.615,0.198 10 false 21 5.625,2.333 6.24,2.531 0.615,0.198 10 false B 5.667,3.125 6.281,3.323 0.615,0.198 10 false IG+ 5.656,3.979 6.271,4.177 0.615,0.198 10 false E2 4.094,2.198 4.708,2.396 0.615,0.198 10 false ECU-B 4.115,2.969 4.854,3.302 0.74,0.333 10 false GAUGE 2.177,2.333 3.552,2.667 1.375,0.333 10 false from Battery 2.063,3.115 3.438,3.448 1.375,0.333 10 false from IG2 Relay 5.083,4.667 5.698,4.865 0.615,0.198 10 false G6 5.094,4.885 7.031,5.156 1.938,0.271 10 false Combination Meter Assembly 0.292,1.927 2.438,2.177 2.146,0.25 10 false No. 3 CAN Junction Connector*1 0.292,2.104 2.438,2.354 2.146,0.25 10 false No. 1 CAN Junction Connector*2 1.906,1.521 2.521,1.719 0.615,0.198 10 false A119 1.896,1 2.51,1.198 0.615,0.198 10 false A119 1.49,1 2.104,1.198 0.615,0.198 10 false G294 1.5,1.521 2.115,1.719 0.615,0.198 10 false G294 1.552,0.792 2.167,0.99 0.615,0.198 10 false 2*1 1.521,1.313 2.135,1.51 0.615,0.198 10 false 13*1 1.938,0.771 2.552,0.969 0.615,0.198 10 false 10*2 1.948,1.313 2.563,1.51 0.615,0.198 10 false 21*2 0.667,4.458 1.563,4.719 0.896,0.26 10 false *1: for LHD 0.667,4.729 1.563,4.99 0.896,0.26 10 false *2: for RHD

CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key, switches or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

DTC check procedure: Turn the ignition switch to ON, wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform CAN Bus Check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.

·

Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.



PROCEDURE

1.CHECK OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY MAIN WIRE)
a.

Disconnect the cable from the negative (-) battery terminal.


b.
C369139C18
1.5,0.75 1.917,1 0.417,0.25 2.927,1.958 2.74,2.583 2.74,2.583 2.573,2.583 true 2.792,1.938 2.635,2.354 2.635,2.354 2.469,2.354 true 1.615,0.792 2.052,0.99 0.438,0.198 10 false G6 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 2.083,2.26 2.583,2.448 0.5,0.188 10 false CANL 2.167,2.5 2.667,2.688 0.5,0.188 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω




OK

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)

NG

REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (POWER SOURCE CIRCUIT)
a.
C369139C17
1.5,0.75 1.917,1 0.417,0.25 1.646,2.333 1.479,2.333 1.479,2.333 1.385,1.938 true 1.49,2.552 1.323,2.552 1.323,2.552 1.156,1.958 true 0.896,1.958 0.771,2.573 0.771,2.573 0.604,2.573 true 1.615,0.792 2.052,0.99 0.438,0.198 10 false G6 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 1.708,2.26 2.208,2.448 0.5,0.188 10 false IG+ 1.542,2.479 2.042,2.667 0.5,0.188 10 false B 0.354,2.5 0.708,2.688 0.354,0.188 10 false E2
*a Front view of wire harness connector
(to Combination Meter Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-21 (E2) - Body ground Cable disconnected from negative (-) battery terminal Below 1 Ω



b.

Reconnect the cable to the negative (-) battery terminal.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
G6-26 (B) - Body ground Always 11 to 14 V
G6-28 (IG+) - Body ground Ignition switch ON 11 to 14 V
Ignition switch off Below 1 V




OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)