Home › Power Source / Network › NETWORKING › CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU) › from 2020.08
RM27T0E _57 Power Source / Network _053729 NETWORKING _0325853 CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU) J

NETWORKING  CAN COMMUNICATION SYSTEM(w/o Central Gateway ECU)  Open in CAN Main Wire  


DESCRIPTION

There may be an open circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.

Symptom Trouble Area

*1: for LHD

*2: for RHD

The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 70 Ω or higher.
·

Open in CAN main bus wire

·

ECM

·

Combination meter assembly

·

No. 1 CAN junction connector

·

No. 2 CAN junction connector*1

·

No. 3 CAN junction connector*1

·

No. 4 CAN junction connector*2

·

No. 5 CAN junction connector*1

·

No. 6 CAN junction connector*2

·

DLC3 CAN branch wire or connector



WIRING DIAGRAM

for LHD


C382850E04
5.521,1.042 5.833,1.24 0.313,0.198 10 false G6 5.51,1.208 6.688,1.615 1.177,0.406 10 false Combination Meter Assembly 5.938,0.885 6.396,1.094 0.458,0.208 10 false CANL 5.938,0.271 6.396,0.479 0.458,0.208 10 false CANH 5.677,0.24 6.135,0.448 0.458,0.208 10 false 40 5.677,0.635 6.135,0.844 0.458,0.208 10 false 39 0.708,0.646 1.167,0.854 0.458,0.208 10 false 13 0.729,0.271 1.188,0.479 0.458,0.208 10 false 2 0.719,1.667 1.177,1.875 0.458,0.208 10 false 16 0.74,1.271 1.198,1.479 0.458,0.208 10 false 5 0.719,3.26 1.177,3.469 0.458,0.208 10 false 12 0.74,2.854 1.198,3.063 0.458,0.208 10 false 1 1.979,2.094 2.438,2.302 0.458,0.208 10 false G317 2,2.26 2.458,2.469 0.458,0.208 10 false DLC3 2.042,1.396 2.5,1.604 0.458,0.208 10 false CANH 2.031,1.802 2.49,2.01 0.458,0.208 10 false CANL 1.781,1.656 2.24,1.865 0.458,0.208 10 false 14 1.813,1.271 2.271,1.479 0.458,0.208 10 false 6 0.063,3.771 0.521,3.979 0.458,0.208 10 false G294 0.063,3.948 1.344,4.333 1.281,0.385 10 false No. 3 CAN Junction Connector 1.479,3.667 1.938,3.875 0.458,0.208 10 false G293 1.51,3.833 2.729,4.365 1.219,0.531 10 false No. 2 CAN Junction Connector 2.938,3.74 3.396,3.948 0.458,0.208 10 false G296 2.948,3.917 4.167,4.458 1.219,0.542 10 false No. 5 CAN Junction Connector 4.365,3.75 4.823,3.958 0.458,0.208 10 false A119 4.365,3.927 5.698,4.427 1.333,0.5 10 false No. 1 CAN Junction Connector 6.083,3.75 6.542,3.958 0.458,0.208 10 false G183 6.083,3.906 6.542,4.115 0.458,0.208 10 false ECM 5.938,2.833 6.396,3.042 0.458,0.208 10 false CANH 5.927,3.469 6.385,3.677 0.458,0.208 10 false CANL 5.677,3.219 6.135,3.427 0.458,0.208 10 false 31 5.677,2.823 6.135,3.031 0.458,0.208 10 false 25 4.958,2.833 5.417,3.042 0.458,0.208 10 false 10 4.99,3.24 5.448,3.448 0.458,0.208 10 false 21 4.208,3.26 4.667,3.469 0.458,0.208 10 false 20 4.271,2.844 4.729,3.052 0.458,0.208 10 false 9 3.688,2.844 4.146,3.052 0.458,0.208 10 false 6 3.667,3.25 4.125,3.458 0.458,0.208 10 false 17 2.958,3.24 3.417,3.448 0.458,0.208 10 false 12 3.021,2.844 3.479,3.052 0.458,0.208 10 false 1 2.396,3.271 2.854,3.479 0.458,0.208 10 false 12 2.448,2.844 2.906,3.052 0.458,0.208 10 false 1 1.729,2.865 2.188,3.073 0.458,0.208 10 false 6 1.677,3.25 2.135,3.458 0.458,0.208 10 false 17


for RHD


C382851E03
5.594,1.125 5.906,1.323 0.313,0.198 10 false G6 5.604,1.292 6.833,1.667 1.229,0.375 10 false Combination Meter Assembly 5.938,0.875 6.427,1.104 0.49,0.229 10 false CANL 5.948,0.26 6.438,0.49 0.49,0.229 10 false CANH 5.906,2.823 6.396,3.052 0.49,0.229 10 false CANH 5.917,3.49 6.406,3.719 0.49,0.229 10 false CANL 5.969,3.781 6.385,3.979 0.417,0.198 10 false G183 5.979,3.969 6.521,4.25 0.542,0.281 10 false ECM 5.656,3.24 6.146,3.469 0.49,0.229 10 false 31 5.667,2.833 6.156,3.063 0.49,0.229 10 false 25 4.896,2.802 5.385,3.031 0.49,0.229 10 false 2 4.885,3.26 5.375,3.49 0.49,0.229 10 false 13 3.906,3.667 4.396,3.896 0.49,0.229 10 false G297 3.927,3.833 5.198,4.281 1.271,0.448 10 false No. 6 CAN Junction Connector 0.146,3.802 0.635,4.031 0.49,0.229 10 false G295 0.167,3.99 1.438,4.438 1.271,0.448 10 false No. 4 CAN Junction Connector 4.146,3.26 4.635,3.49 0.49,0.229 10 false 12 4.219,2.833 4.708,3.063 0.49,0.229 10 false 1 0.698,3.229 1.188,3.458 0.49,0.229 10 false 12 0.698,2.802 1.188,3.031 0.49,0.229 10 false 1 0.688,1.25 1.177,1.479 0.49,0.229 10 false 4 0.677,1.656 1.167,1.885 0.49,0.229 10 false 15 1.948,2.115 2.542,2.417 0.594,0.302 10 false G317 1.948,2.281 2.438,2.51 0.49,0.229 10 false DLC3 2.031,1.792 2.521,2.021 0.49,0.229 10 false CANL 2.021,1.385 2.51,1.615 0.49,0.229 10 false CANH 1.771,1.667 2.26,1.896 0.49,0.229 10 false 14 1.823,1.26 2.313,1.49 0.49,0.229 10 false 6 3.927,0.99 4.417,1.219 0.49,0.229 10 false A119 3.917,1.198 5.188,1.646 1.271,0.448 10 false No. 1 CAN Junction Connector 4.865,0.646 5.354,0.875 0.49,0.229 10 false 21 4.865,0.26 5.354,0.49 0.49,0.229 10 false 10 5.635,0.26 6.125,0.49 0.49,0.229 10 false 40 5.635,0.635 6.125,0.865 0.49,0.229 10 false 39 4.188,0.24 4.677,0.469 0.49,0.229 10 false 9 4.125,0.635 4.615,0.865 0.49,0.229 10 false 20 0.698,0.229 1.188,0.458 0.49,0.229 10 false 8 0.708,0.625 1.198,0.854 0.49,0.229 10 false 19


CAUTION / NOTICE / HINT

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


NOTICE:
·

Because the order of diagnosis is important to allow correct diagnosis, make sure to begin troubleshooting using How to Proceed with Troubleshooting when CAN communication system related DTCs are output.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING

·

Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.

·

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When disconnecting and reconnecting the battery.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART


·

Some parts must be initialized and set when replacing or removing and installing parts.

Click hereGeneral>SETUP>WHEN REPLACING OR REMOVING/INSTALLING PARTS>WORK PROCEDURE

·

After performing repairs, perform the DTC check procedure and confirm that the DTCs are not output again.

DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.

·

After the repair, perform the CAN bus check and check that all the ECUs and sensors connected to the CAN communication system are displayed as normal.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>DIAGNOSIS SYSTEM

·

When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.



HINT:
·

Before disconnecting related connectors for inspection, push in on each connector body to check that the connector is not loose or disconnected.

·

When a connector is disconnected, check that the terminals and connector body are not cracked, deformed or corroded.



PROCEDURE

1.CHECK FOR OPEN IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)
a.
C416806C09
0.115,0.99 0.521,1.25 0.406,0.26 1.948,0.917 1.552,0.385 1.552,0.385 1.406,0.385 true 1.958,1.375 2.052,1.906 2.052,1.906 2.167,1.906 true 0.135,0.115 0.448,0.271 0.313,0.156 10 false *a 0.156,1.042 0.531,1.26 0.375,0.219 10 false G317 1,0.333 1.49,0.479 0.49,0.146 10 false CANH 2.229,1.844 2.844,2.042 0.615,0.198 10 false CANL
*a Front view of DLC3


Disconnect the cable from the negative (-) battery terminal.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G317-6 (CANH) - G317-14 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω


NOTICE:

When the measured value is 133 Ω or higher and a CAN communication system DTC is output, there may be a fault besides disconnection of the DLC3 branch line. For that reason, troubleshooting should be performed again from How to Proceed with Troubleshooting after repairing the trouble area.

Click herePower Source / Network>NETWORKING>CAN COMMUNICATION SYSTEM (w/o Central Gateway ECU)>HOW TO PROCEED WITH TROUBLESHOOTING



Result:
Result Proceed to
OK (for LHD) A
OK (for RHD) B
NG C



A

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)

B

13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)

C

REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)

2.CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 2 CAN junction connector.

C382852C05
1.052,1.24 1.458,1.49 0.406,0.25 2.458,0.594 2.708,0.594 2.708,0.594 2.708,1.375 true 2.469,2.135 2.719,2.135 2.719,2.135 2.719,1.719 true 3.75,0.385 3.583,0.385 3.583,0.385 3.583,1.385 true 3.75,2.385 3.583,2.385 3.583,2.385 3.583,1.719 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.083,1.292 1.583,1.531 0.5,0.24 10 false G293 1.896,0.521 2.563,0.76 0.667,0.24 10 false CANH*b 1.938,2.052 2.604,2.292 0.667,0.24 10 false CANL*b 3.802,0.313 4.469,0.552 0.667,0.24 10 false CANH*c 3.802,2.313 4.469,2.552 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 2 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
*c to No. 3 CAN Junction Connector - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G293-1 (CANH) - G293-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector
G293-6 (CANH) - G293-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 3 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 3 CAN junction connector CAN main wire) B
NG (No. 5 CAN junction connector CAN main wire) C



A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

B

3.CONNECT CONNECTOR

C

7.CONNECT CONNECTOR
3.CONNECT CONNECTOR
a.

Reconnect the G293 No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
4.CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 3 CAN junction connector.

C382856C03
1.813,1.198 2.198,1.427 0.385,0.229 2.542,0.542 2.708,0.542 2.708,0.542 2.708,1.375 true 2.552,2.24 2.719,2.24 2.719,2.24 2.719,1.74 true 2.708,0.354 2.875,0.354 2.875,0.354 2.875,1.354 true 2.719,2.458 2.885,2.458 2.885,2.458 2.885,1.729 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,1.229 2.219,1.427 0.385,0.198 10 false G294 1.969,0.458 2.552,0.688 0.583,0.229 10 false CANH*b 2.031,2.156 2.615,2.385 0.583,0.229 10 false CANL*b 2.135,0.271 2.719,0.5 0.583,0.229 10 false CANH*c 2.188,2.365 2.771,2.594 0.583,0.229 10 false CANL*c
*a Front view of wire harness connector
(to No. 3 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to Combination Meter Assembly - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G294-1 (CANH) - G294-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
G294-2 (CANH) - G294-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly



Result:
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 2 CAN junction connector CAN main wire) C



A

REPLACE NO. 3 CAN JUNCTION CONNECTOR

B

5.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

5.CONNECT CONNECTOR
a.

Reconnect the G294 No. 3 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

6.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)
6.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)
a.
C369139C18
1.5,0.75 1.917,1 0.417,0.25 2.927,1.958 2.74,2.583 2.74,2.583 2.573,2.583 true 2.792,1.938 2.635,2.354 2.635,2.354 2.469,2.354 true 1.615,0.792 2.052,0.99 0.438,0.198 10 false G6 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 2.083,2.26 2.583,2.448 0.5,0.188 10 false CANL 2.167,2.5 2.667,2.688 0.5,0.188 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 3 CAN JUNCTION CONNECTOR)

7.CONNECT CONNECTOR
a.

Reconnect the G293 No. 2 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

8.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
8.CHECK FOR OPEN IN CAN BUS WIRE (NO. 5 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 5 CAN junction connector.

C382852C06
1.052,1.24 1.458,1.49 0.406,0.25 2.458,0.594 2.708,0.594 2.708,0.594 2.708,1.375 true 2.469,2.135 2.719,2.135 2.719,2.135 2.719,1.719 true 3.74,0.563 3.573,0.563 3.573,0.563 3.573,1.365 true 3.75,2.177 3.583,2.177 3.583,2.177 3.583,1.729 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.083,1.292 1.583,1.531 0.5,0.24 10 false G296 1.896,0.521 2.563,0.76 0.667,0.24 10 false CANH*b 1.938,2.052 2.604,2.292 0.667,0.24 10 false CANL*b 3.781,0.49 4.448,0.729 0.667,0.24 10 false CANH*c 3.792,2.094 4.458,2.333 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 5 CAN Junction Connector)
*b to No. 2 CAN Junction Connector
*c to No. 1 CAN Junction Connector - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G296-1 (CANH) - G296-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 2 CAN junction connector
G296-6 (CANH) - G296-17 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (No. 2 CAN junction connector CAN main wire) C



A

REPLACE NO. 5 CAN JUNCTION CONNECTOR

B

9.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 5 CAN JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

9.CONNECT CONNECTOR
a.

Reconnect the G296 No. 5 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
10.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C382854C02
0.594,1.167 1.01,1.469 0.417,0.302 3.667,0.5 3.833,0.5 3.833,0.5 3.99,1.271 true 3.865,0.24 4.031,0.24 4.031,0.24 4.177,1.292 true 3.896,2.448 4.063,2.448 4.063,2.448 4.208,1.552 true 3.583,2.25 3.75,2.25 3.75,2.25 4.01,1.531 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.625,1.219 1.01,1.458 0.385,0.24 10 false A119 3.115,0.417 3.75,0.698 0.635,0.281 10 false CANH*b 3.333,0.156 3.969,0.438 0.635,0.281 10 false CANH*c 3.365,2.385 4,2.667 0.635,0.281 10 false CANL*c 3.021,2.167 3.656,2.448 0.635,0.281 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 5 CAN Junction Connector
*c to ECM - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A119-9 (CANH) - A119-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 5 CAN junction connector
A119-10 (CANH) - A119-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM



Result:
Result Proceed to
OK A
NG (ECM CAN main wire) B
NG (No. 5 CAN junction connector CAN main wire) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

11.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 5 CAN JUNCTION CONNECTOR)

11.CONNECT CONNECTOR
a.

Reconnect the A119 No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

12.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 1 CAN JUNCTION CONNECTOR)
12.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 1 CAN JUNCTION CONNECTOR)
a.
C334423C06
1.354,0.115 1.813,0.396 0.458,0.281 2.271,1.646 2.521,1.938 2.521,1.938 2.656,1.938 true 2.271,1.406 2.51,1.229 2.51,1.229 2.646,1.229 true 0.094,0.094 0.417,0.292 0.323,0.198 10 false *a 2.729,1.146 3.344,1.344 0.615,0.198 10 false CANH 1.417,0.177 2.031,0.375 0.615,0.198 10 false G183 2.74,1.854 3.354,2.052 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G183-25 (CANH) - G183-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - NO. 1 CAN JUNCTION CONNECTOR)

13.CHECK FOR OPEN IN CAN BUS WIRE (NO. 4 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 4 CAN junction connector.

C382852C07
1.052,1.24 1.458,1.49 0.406,0.25 2.135,0.938 2.385,0.938 2.385,0.938 2.656,1.406 true 2.188,1.969 2.438,1.969 2.438,1.969 2.719,1.698 true 4.427,0.625 4.26,0.625 4.26,0.625 3.958,1.375 true 4.396,2.146 4.229,2.146 4.229,2.146 3.938,1.74 true 0.083,0.063 0.396,0.26 0.313,0.198 10 false *a 1.083,1.292 1.583,1.531 0.5,0.24 10 false G295 1.594,0.823 2.26,1.063 0.667,0.24 10 false CANH*b 1.667,1.875 2.333,2.115 0.667,0.24 10 false CANL*b 4.469,0.552 5.135,0.792 0.667,0.24 10 false CANH*c 4.448,2.073 5.115,2.313 0.667,0.24 10 false CANL*c
*a Front view of wire harness connector
(to No. 4 CAN Junction Connector)
*b to No. 6 CAN Junction Connector
*c to No. 1 CAN Junction Connector - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G295-1 (CANH) - G295-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 6 CAN junction connector
G295-8 (CANH) - G295-19 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 1 CAN junction connector



Result:
Result Proceed to
OK A
NG (No. 1 CAN junction connector CAN main wire) B
NG (No. 6 CAN junction connector CAN main wire) C



A

REPLACE NO. 4 CAN JUNCTION CONNECTOR

B

14.CONNECT CONNECTOR

C

18.CONNECT CONNECTOR
14.CONNECT CONNECTOR
a.

Reconnect the G295 No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

15.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
15.CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 1 CAN junction connector.

C382854C03
0.594,1.167 1.01,1.469 0.417,0.302 3.667,0.5 3.833,0.5 3.833,0.5 3.99,1.271 true 3.865,0.24 4.031,0.24 4.031,0.24 4.177,1.292 true 3.896,2.448 4.063,2.448 4.063,2.448 4.208,1.552 true 3.583,2.25 3.75,2.25 3.75,2.25 4.01,1.531 true 0.104,0.083 0.417,0.281 0.313,0.198 10 false *a 0.625,1.219 1.01,1.458 0.385,0.24 10 false A119 3.115,0.417 3.75,0.698 0.635,0.281 10 false CANH*b 3.333,0.156 3.969,0.438 0.635,0.281 10 false CANH*c 3.365,2.385 4,2.667 0.635,0.281 10 false CANL*c 3.021,2.167 3.656,2.448 0.635,0.281 10 false CANL*b
*a Front view of wire harness connector
(to No. 1 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to Combination Meter Assembly - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
A119-9 (CANH) - A119-20 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector
A119-10 (CANH) - A119-21 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω Combination meter assembly



Result:
Result Proceed to
OK A
NG (Combination meter assembly CAN main wire) B
NG (No. 4 CAN junction connector CAN main wire) C



A

REPLACE NO. 1 CAN JUNCTION CONNECTOR

B

16.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

16.CONNECT CONNECTOR
a.

Reconnect the A119 No. 1 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

17.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
17.CHECK FOR OPEN IN CAN BUS WIRE (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)
a.
C369139C18
1.5,0.75 1.917,1 0.417,0.25 2.927,1.958 2.74,2.583 2.74,2.583 2.573,2.583 true 2.792,1.938 2.635,2.354 2.635,2.354 2.469,2.354 true 1.615,0.792 2.052,0.99 0.438,0.198 10 false G6 0.135,0.083 0.448,0.281 0.313,0.198 10 false *a 2.083,2.26 2.583,2.448 0.5,0.188 10 false CANL 2.167,2.5 2.667,2.688 0.5,0.188 10 false CANH
*a Front view of wire harness connector
(to Combination Meter Assembly)


Disconnect the combination meter assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G6-40 (CANH) - G6-39 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (COMBINATION METER ASSEMBLY - NO. 1 CAN JUNCTION CONNECTOR)

18.CONNECT CONNECTOR
a.

Reconnect the G295 No. 4 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

19.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
19.CHECK FOR OPEN IN CAN BUS WIRE (NO. 6 CAN JUNCTION CONNECTOR)
a.

Disconnect the No. 6 CAN junction connector.

C382856C05
1.813,1.198 2.198,1.427 0.385,0.229 2.542,0.542 2.708,0.542 2.708,0.542 2.708,1.375 true 2.552,2.24 2.719,2.24 2.719,2.24 2.719,1.74 true 2.708,0.354 2.875,0.354 2.875,0.354 2.875,1.354 true 2.719,2.458 2.885,2.458 2.885,2.458 2.885,1.729 true 0.083,0.073 0.396,0.271 0.313,0.198 10 false *a 1.833,1.229 2.292,1.458 0.458,0.229 10 false G297 1.969,0.458 2.552,0.688 0.583,0.229 10 false CANH*b 2.031,2.156 2.615,2.385 0.583,0.229 10 false CANL*b 2.135,0.271 2.719,0.5 0.583,0.229 10 false CANH*c 2.188,2.365 2.771,2.594 0.583,0.229 10 false CANL*c
*a Front view of wire harness connector
(to No. 6 CAN Junction Connector)
*b to No. 4 CAN Junction Connector
*c to ECM - -



b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition Connected to
G297-1 (CANH) - G297-12 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω No. 4 CAN junction connector
G297-2 (CANH) - G297-13 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω ECM



Result:
Result Proceed to
OK A
NG (ECM CAN main wire) B
NG (No. 4 CAN junction connector CAN main wire) C



A

REPLACE NO. 6 CAN JUNCTION CONNECTOR

B

20.CONNECT CONNECTOR

C

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - NO. 4 CAN JUNCTION CONNECTOR)

20.CONNECT CONNECTOR
a.

Reconnect the G297 No. 6 CAN junction connector.


Result:
Proceed to
NEXT



NEXT

21.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 6 CAN JUNCTION CONNECTOR)
21.CHECK FOR OPEN IN CAN BUS WIRE (ECM - NO. 6 CAN JUNCTION CONNECTOR)
a.
C334423C06
1.354,0.115 1.813,0.396 0.458,0.281 2.271,1.646 2.521,1.938 2.521,1.938 2.656,1.938 true 2.271,1.406 2.51,1.229 2.51,1.229 2.646,1.229 true 0.094,0.094 0.417,0.292 0.323,0.198 10 false *a 2.729,1.146 3.344,1.344 0.615,0.198 10 false CANH 1.417,0.177 2.031,0.375 0.615,0.198 10 false G183 2.74,1.854 3.354,2.052 0.615,0.198 10 false CANL
*a Front view of wire harness connector
(to ECM)


Disconnect the ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G183-25 (CANH) - G183-31 (CANL) Cable disconnected from negative (-) battery terminal 108 to 132 Ω



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (ECM - NO. 6 CAN JUNCTION CONNECTOR)