Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P052012  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery  P052014  Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open  


DESCRIPTION

Refer to DTC P052477.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P052477

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P052012 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Battery Conditions (a) and (b) continue for 5 seconds or more:

(a) Ignition switch is ON.

(b) Oil pressure sender gauge assembly voltage is 4.78 V or higher.


(1 trip detection logic)
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Comes on DTC stored SAE Code: P0523
P052014 Engine Oil Pressure Sensor/Switch "A" Circuit Short to Ground or Open Conditions (a) and (b) continue for 5 seconds or more:

(a) Ignition switch is ON.

(b) Oil pressure sender gauge assembly voltage is 0.23 V or less.


(1 trip detection logic)
·

Open or short in oil pressure sender gauge assembly circuit

·

Oil pressure sender gauge assembly

·

ECM


Comes on DTC stored SAE Code: P0522

Related Data List
DTC No. Data List
P052012
P052014
Engine Oil Pressure

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P052012
P052014
Idling for 5 seconds or more

WIRING DIAGRAM

A474990E02
1.115,1.719 1.646,1.927 0.531,0.208 10 false PEO 1.198,1.031 1.729,1.24 0.531,0.208 10 false VC 1.24,2.5 1.771,2.708 0.531,0.208 10 false E2 4.75,0.938 5.281,1.146 0.531,0.208 10 false VCPE 4.479,1.156 5.01,1.365 0.531,0.208 10 false 34 4.5,2.615 5.031,2.823 0.531,0.208 10 false 35 4.479,1.854 5.01,2.063 0.531,0.208 10 false 26 4.885,2.125 5.417,2.333 0.531,0.208 10 false 200 kΩ 4.75,2.396 5.281,2.604 0.531,0.208 10 false EPEO 4.75,1.625 5.281,1.833 0.531,0.208 10 false PEO 5.604,3.26 6.135,3.469 0.531,0.208 10 false ECM 5.604,3.104 6.135,3.313 0.531,0.208 10 false C150 0.24,2.896 0.771,3.104 0.531,0.208 10 false C123 0.24,3.063 2.948,3.313 2.708,0.25 10 false Oil Pressure Sender Gauge Assembly 1.5,0.927 2.031,1.135 0.531,0.208 10 false 3 1.51,1.615 2.042,1.823 0.531,0.208 10 false 2 1.521,2.396 2.052,2.604 0.531,0.208 10 false 1 6.115,0.688 6.646,0.896 0.531,0.208 10 false 5 V

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (OIL PRESSURE SENDER GAUGE ASSEMBLY - ECM)
a.

Disconnect the oil pressure sender gauge assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C123-3 (VC) - C150-34 (VCPE) Always Below 1 Ω
C123-2 (PEO) - C150-26 (PEO) Always Below 1 Ω
C123-1 (E2) - C150-35 (EPEO) Always Below 1 Ω
C123-3 (VC) or C150-34 (VCPE) - Body ground and other terminals Always 10 kΩ or higher
C123-2 (PEO) or C150-26 (PEO) - Body ground and other terminals Always 10 kΩ or higher
C123-1 (E2) or C150-35 (EPEO) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR

NG

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
2.CHECK HARNESS AND CONNECTOR
HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.
A241069C76
0.448,1.073 0.927,1.333 0.479,0.26 1.833,1.333 2.125,1.844 true 1.625,1.365 1.615,1.802 true 1.396,1.333 1.104,1.854 true 0.094,0.083 0.323,0.313 0.229,0.229 10 false *a 2.135,1.875 2.427,2.052 0.292,0.177 10 false VC 0.521,1.125 0.875,1.302 0.354,0.177 10 false C123 0.99,1.875 1.51,2.052 0.521,0.177 10 false E2 1.438,1.875 1.969,2.052 0.531,0.177 10 false PEO
*a Front view of wire harness connector
(to Oil Pressure Sender Gauge Assembly)


Disconnect the oil pressure sender gauge assembly connector.


b.

Turn the ignition switch to ON.


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C123-3 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
C123-2 (PEO) - Body ground Ignition switch ON Below 0.1 V



d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
C123-2 (PEO) - C123-1 (E2) Ignition switch off No short or no open circuit
C123-1 (E2) - Body ground Ignition switch off Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY

NG

5.REPLACE ECM
3.REPLACE OIL PRESSURE SENDER GAUGE ASSEMBLY
a.

Replace the oil pressure sender gauge assembly.

Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SENSOR>REMOVAL


Result:
Proceed to
NEXT



NEXT

4.CHECK IF DTC OUTPUT RECURS (DTC P052012 OR P052014)
4.CHECK IF DTC OUTPUT RECURS (DTC P052012 OR P052014)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Start the engine and idle it for 5 second or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Read the DTCs.

Result:
Result Proceed to
DTC P052012 or P052014 is output A
DTCs are not output B




A

5.REPLACE ECM

B

END

5.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Turn the ignition switch to ON and turn the GTS on.


f.

Start the engine and idle it for 5 seconds or more.


g.

Enter the following menus: Powertrain / Engine / Trouble Codes.


h.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

7.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED