The oil pressure control system reduces and increases engine oil pressure using the oil pressure switching valve in the timing gear case assembly. When the engine speed reaches 2600 rpm while racing the engine after warming it up, the oil pressure switching valve operates and the engine oil pressure system changes from low pressure control mode to high pressure control mode. When the engine speed drops to 2400 rpm, the engine oil pressure system changes from high pressure control mode to low pressure control mode. The oil pressure sender gauge assembly detects the engine oil pressure.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P052477 | Engine Oil Pressure Too Low (Severe) | Conditions (a) and (b) continue for 8 seconds or more:
(a) 0.3 seconds have elapsed after sending a command to change from low oil pressure control mode to high oil pressure control mode. (b) The oil pressure control system does not change to high oil pressure control mode. (1 trip detection logic) |
·
Short in oil pressure sender gauge assembly circuit ·
Oil pressure sender gauge assembly ·
Oil pressure switching valve assembly ·
ECM ·
Oil pump assembly (Timing chain case assembly) ·
Engine oil amount insufficient ·
EFI MAIN NO. 2 relay |
Comes on | DTC stored | SAE Code: P0524 |
| DTC No. | Data List |
|---|---|
| P052477 | ·
Engine Oil Pressure ·
Engine Oil Pressure VSV |
Refer to DTC P052012.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P052012
Refer to DTC P06DA12.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>P06DA12
Inspect the fuses of circuits related to this system before performing the following inspection procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
An output DTC does not necessarily indicate that there is a malfunction. DTCs may have been stored due to an insufficient engine oil amount even though the oil level warning light is currently not illuminated, such as when engine oil is added by the customer.
Check the engine oil level.
Check the state of the oil level warning light.
| Result | Proceed to |
|---|---|
| Engine oil level is low and oil level warning light is illuminated | A |
| Engine oil level is within the specified range and oil level warning light is not illuminated | B |
If the oil level warning light is not illuminated even though the engine oil level is lower than the Low mark, or the oil level warning light is illuminated even though the engine oil level is within the specified range, inspect the oil level sensor and related parts for malfunctions.
A
B
Check for engine oil leaks.
If there are engine oil leaks, perform repairs.
| Proceed to |
|---|
| NEXT |
NEXT
Add engine oil.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.
Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check the difference.
50 kPa or higher
| Proceed to |
|---|
| OK |
| NG |
NG
OK
Disconnect the oil pressure switching valve assembly connector.
Make sure that the engine is stopped before disconnecting the connector of the oil pressure switching valve assembly.
Make sure that the disconnected connector does not get caught in moving engine parts.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.
Check the engine oil pressure value.
| Result | Proceed to |
|---|---|
| Engine oil pressure rises to between 250 and 510 kPa | A |
| Except above | B |
Low oil pressure control mode is not performed when the connector of the oil pressure switching valve assembly is disconnected. Therefore, if the measurement results from Engine Oil Pressure Control Check all indicate oil pressure values which are high, it can be determined that there is an electrical malfunction.
A
B
Inspect the No. 1 integration relay.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/o Urea SCR System)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Remove the No. 1 integration relay.
Disconnect the oil pressure switching valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C130-2 - Body ground* | Always | 10 kΩ or higher |
| C130-1 - Body ground | Always | 10 kΩ or higher |
*: Make sure that there are no short circuits to the battery.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace the oil pump assembly.
| Proceed to |
|---|
| NEXT |
NEXT
Replace the No. 1 integration relay.
| Proceed to |
|---|
| NEXT |
NEXT
Inspect the engine oil pressure
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>LUBRICATION SYSTEM>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the oil pressure sender gauge assembly.
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SENSOR>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Replace the oil pressure switching valve assembly.
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PRESSURE SWITCHING VALVE>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.
Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check the difference.
50 kPa or higher
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Repair or replace the oil pump assembly.
Click hereEngine / Hybrid System>1GD-FTV (LUBRICATION)>OIL PUMP>REMOVAL
If the oil pressure does not rise after disconnecting the connector of the oil pressure switching valve assembly, or if the oil pressure changes, but the difference between the low oil pressure and high oil pressure is small, a mechanical malfunction is probably the cause.
The sleeve is locked due to foreign matter.
The oil pressure relief valve is locked due to foreign matter.
The check valve is stuck.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the ignition switch to ON and turn the GTS on.
Clear the DTCs.
Turn the ignition switch off for 30 seconds or more.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Enter the following menus: Powertrain / Engine / Utility / Engine Oil Pressure Control Check.
Compare the "valve off" (high pressure control mode) and "valve on" (low pressure control mode) oil pressure values and check that the oil pressure has risen.
| Proceed to |
|---|
| NEXT |
NEXT