Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM J

1GD-FTV ENGINE CONTROL  ECD SYSTEM  Starter Signal Circuit  


DESCRIPTION

While the engine is being cranked, the starter signal is also sent to terminal STA of the ECM. The starter signal mainly performs engine control when the engine is started.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:

This procedure is based on the premise that the engine can crank normally. If the engine cannot crank normally, proceed to the problem symptoms table.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE


PROCEDURE

1.READ VALUE USING GTS (STARTER SIGNAL)
a.

Connect the GTS to DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Primary / Starter SW.


d.

Check the value displayed on the GTS when the ignition switch is turned the to ON and START positions.

OK:
Switch Condition Starter SW
ON OFF
START ON



Result:
Proceed to
OK
NG (for Manual transmission)
NG (for Automatic transmission)



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG (for Manual transmission)

2.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH ASSEMBLY)

NG (for Automatic transmission)

3.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH ASSEMBLY)
HINT:
·

*1: for LHD

·

*2: for RHD



a.

Disconnect the ECM connector.


b.

Disconnect the clutch start switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-22 (STA) - A40-1*1 Always Below 1 Ω
G184-22 (STA) - r1-1*2 Always Below 1 Ω
G184-22 (STA) or A40-1*1 - Body ground and other terminals Always 10 kΩ or higher
G184-22 (STA) or r1-1*2 - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (ECM - PARK/NEUTRAL POSITION SWITCH ASSEMBLY)
a.

Disconnect the ECM connector.


b.

Disconnect the park/neutral position switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
G184-22 (STA) - C159-5 (L) Always Below 1 Ω
G184-22 (STA) or C159-5 (L) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR