Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0260475 ECD SYSTEM C

1GD-FTV ENGINE CONTROL  ECD SYSTEM  P061512  Starter Relay Circuit Short to Battery  


DESCRIPTION

While the engine is being cranked, the ECM detects the starter signal (STA signal) and performs engine control when the engine starts.

If the ECM detects the starter control (STA) signal while the vehicle is being driven, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

This monitor runs when the vehicle has been driven at 20 km/h (12.4 mph) or more for more than 20 seconds.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P061512 Starter Relay Circuit Short to Battery Conditions (a), (b) and (c) are met for 20 seconds:

(a) Vehicle speed is more than 20 km/h (12.4 mph).

(b) Engine speed is more than 1000 rpm.

(c) STA signal is on.


(1 trip detection logic)
·

ST relay circuit

·

Ignition switch assembly

·

Park/Neutral position switch assembly*1

·

Clutch start switch assembly*2

·

ECM


Comes on DTC stored SAE Code: P0617

·

*1: for Automatic transmission

·

*2: for Manual transmission


Related Data List
DTC No. Data List
P061512 Starter SW

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P061512 Drive the vehicle for 20 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more

WIRING DIAGRAM

w/ Entry and Start System
A477034E01
0.219,4.073 2.021,4.469 1.802,0.396 10 false Certification ECU (Smart Key ECU Assembly) 0.667,0.417 1.125,0.615 0.458,0.198 10 false NE 0.594,3.5 1.052,3.698 0.458,0.198 10 false STA 0.531,0.823 0.99,1.021 0.458,0.198 10 false STAR 1.031,0.302 1.333,0.469 0.302,0.167 10 false 14 1.031,0.708 1.281,0.906 0.25,0.198 10 false 10 1.042,3.365 1.292,3.604 0.25,0.24 10 false 12 2.896,1.917 5.427,2.177 2.531,0.26 10 false Park/Neutral Position Switch Assembly 3.229,3.135 5.156,3.375 1.927,0.24 10 false Clutch Start Switch Assembly 2.906,5.396 4.135,5.594 1.229,0.198 10 false ST 1.177,5.073 1.542,5.271 0.365,0.198 10 false ST 0.49,5.906 1.719,6.104 1.229,0.198 10 false 250A FL 0.615,7.177 1.198,7.417 0.583,0.24 10 false Battery 2.979,6.885 4.208,7.083 1.229,0.198 10 false Starter Assembly 2.156,6.667 3.385,6.865 1.229,0.198 10 false ST 1.75,6.781 2.979,6.979 1.229,0.198 10 false B 2.135,6.177 2.583,6.365 0.448,0.188 10 false D11 1.406,6.771 1.698,6.948 0.292,0.177 10 false D9 6.375,4.115 7.063,4.323 0.688,0.208 10 false ECM 2.51,6.188 2.833,6.406 0.323,0.219 10 false 1*3 1.396,6.552 1.781,6.771 0.385,0.219 10 false 1*4 6.198,3.521 6.656,3.719 0.458,0.198 10 false STA 6.198,0.833 6.656,1.031 0.458,0.198 10 false NSW 6.198,0.427 6.656,0.625 0.458,0.198 10 false NEO 5.948,0.302 6.198,0.5 0.25,0.198 10 false 23 5.927,0.708 6.177,0.906 0.25,0.198 10 false 11 5.927,3.375 6.177,3.573 0.25,0.198 10 false 22 6.354,3.885 6.729,4.083 0.375,0.198 10 false G184 4.844,1.177 5.094,1.417 0.25,0.24 10 false *1 2.948,2.385 3.198,2.625 0.25,0.24 10 false *2 4.448,2.667 4.698,2.906 0.25,0.24 10 false 2 3.271,2.677 3.521,2.917 0.25,0.24 10 false 1 4.833,5.542 6.865,5.781 2.031,0.24 10 false *1: for Automatic Transmission 4.844,5.885 6.646,6.146 1.802,0.26 10 false *2: for Manual Transmission 2.969,1.177 3.219,1.417 0.25,0.24 10 false *1 4.844,2.396 5.094,2.635 0.25,0.24 10 false *2 2.906,1.719 3.625,1.917 0.719,0.198 10 false C159 3.26,1.438 3.51,1.677 0.25,0.24 10 false 5 4.458,1.427 4.708,1.667 0.25,0.24 10 false 4 3.5,1.438 3.75,1.677 0.25,0.24 10 false L 4.208,1.438 4.458,1.677 0.25,0.24 10 false B 3.25,2.948 4.25,3.156 1,0.208 10 false A40*5, r1*6 2.729,5.781 2.979,6.021 0.25,0.24 10 false 1 2.74,5 2.99,5.24 0.25,0.24 10 false 2 2.104,5.021 2.354,5.26 0.25,0.24 10 false 5 2.094,5.802 2.333,6.052 0.24,0.25 10 false 3 0.219,3.885 0.813,4.073 0.594,0.188 10 false G213 2.135,6.417 2.583,6.604 0.448,0.188 10 false D10 2.51,6.417 2.792,6.625 0.281,0.208 10 false 1*4 0.979,6.781 1.271,6.958 0.292,0.177 10 false D8 4.844,6.25 6.646,6.51 1.802,0.26 10 false *3: for 2.0 kW type 4.844,6.604 6.646,6.865 1.802,0.26 10 false *4: for 2.7 kW type 4.854,6.979 6.656,7.24 1.802,0.26 10 false *5: for LHD 4.833,7.333 6.635,7.594 1.802,0.26 10 false *6: for RHD 0.969,6.563 1.354,6.781 0.385,0.219 10 false 1*3

w/o Entry and Start System
A448877E29
0.635,1.188 0.948,1.385 0.313,0.198 10 false G2 0.635,1.365 2.24,1.594 1.604,0.229 10 false Ignition Switch Assembly 0.542,0.667 0.854,0.865 0.313,0.198 10 false 7 1.823,0.667 2.135,0.865 0.313,0.198 10 false 8 0.74,0.667 1.115,0.844 0.375,0.177 10 false AM2 1.469,0.667 1.844,0.844 0.375,0.177 10 false ST2 2.948,1.375 3.26,1.573 0.313,0.198 10 false 4 2.927,2.458 3.24,2.656 0.313,0.198 10 false 2 4.052,2.458 4.365,2.656 0.313,0.198 10 false 1 4.042,1.375 4.354,1.573 0.313,0.198 10 false 5 2.385,1.813 2.802,2.01 0.417,0.198 10 false C159 2.823,2.927 3.948,3.156 1.125,0.229 10 false A40*3, r1*4 2.375,2 5.031,2.24 2.656,0.24 10 false Park/Neutral Position Switch Assembly 2.802,3.104 4.823,3.313 2.021,0.208 10 false Clutch Start Switch Assembly 5.281,0.656 5.594,0.854 0.313,0.198 10 false 11 5.302,3.406 5.615,3.604 0.313,0.198 10 false 22 5.583,0.781 6.063,0.979 0.479,0.198 10 false NSW 5.583,3.552 6.063,3.75 0.479,0.198 10 false STA 1.604,5.958 3.208,6.188 1.604,0.229 10 false Starter Assembly 1.396,5.479 1.708,5.677 0.313,0.198 10 false D8 1.948,5 2.26,5.198 0.313,0.198 10 false D11 1.969,5.219 2.281,5.417 0.313,0.198 10 false ST 1.708,5.479 2.021,5.677 0.313,0.198 10 false B 2.292,5 2.604,5.198 0.313,0.198 10 false 1 1.448,5.292 1.76,5.49 0.313,0.198 10 false 1 2.677,4.594 2.99,4.792 0.313,0.198 10 false 1 2.688,3.813 3,4.01 0.313,0.198 10 false 2 1.938,3.813 2.25,4.01 0.313,0.198 10 false 5 1.927,4.594 2.24,4.792 0.313,0.198 10 false 3 2.844,4.198 3.5,4.406 0.656,0.208 10 false ST 1.083,3.708 1.74,3.917 0.656,0.208 10 false ST 0.448,4.552 1.51,4.771 1.063,0.219 10 false 250A FL 5.917,5.01 6.573,5.219 0.656,0.208 10 false ECM 0.521,5.885 1.177,6.094 0.656,0.208 10 false Battery 0.406,2.135 2.01,2.365 1.604,0.229 10 false STRG LOCK/AM2 NO. 1 3.281,5.458 5.938,5.698 2.656,0.24 10 false *2: for Manual Transmission 3.26,5.042 5.917,5.281 2.656,0.24 10 false *1: for Automatic Transmission 3.167,1.594 3.479,1.792 0.313,0.198 10 false B 3.844,1.594 4.156,1.792 0.313,0.198 10 false L 2.531,1.354 2.844,1.552 0.313,0.198 10 false *1 4.406,1.375 4.719,1.573 0.313,0.198 10 false *1 2.448,2.458 2.76,2.656 0.313,0.198 10 false *2 4.479,2.469 4.792,2.667 0.313,0.198 10 false *2 5.906,4.833 6.563,5.042 0.656,0.208 10 false G185 3.281,6.313 5.938,6.552 2.656,0.24 10 false *4: for RHD 3.271,5.885 5.927,6.125 2.656,0.24 10 false *3: for LHD

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses of circuits related to this system before performing the following inspection procedure.

·

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>INITIALIZATION).



HINT:
·

The following troubleshooting process is based on the premise that the engine can crank normally. If the engine does not crank, proceed to Problem Symptoms Table (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM>PROBLEM SYMPTOMS TABLE).

·

If this DTC is output, inspect the starter assembly.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.



PROCEDURE

1.READ VALUE USING GTS (STARTER SW)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Data List / Starter SW.


d.

Read the value displayed on the GTS when the vehicle is driven at 20 km/h (12.4 mph) or more with engine speed at 1000 rpm or more.

Result:
GTS Display Result Proceed to
Starter SW OFF A
ON w/ Entry and Start System for Automatic transmission B
for Manual transmission C
w/o Entry and Start System for Automatic transmission D
for Manual transmission E




A

B

2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

C

6.INSPECT CLUTCH START SWITCH

D

8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY

E

13.INSPECT CLUTCH START SWITCH ASSEMBLY
2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

3.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (park/neutral position switch assembly - ST relay - ECM - certification ECU (smart key ECU assembly)).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P061512)
4.CHECK WHETHER DTC OUTPUT RECURS (DTC P061512)
a.

Connect the GTS to the DLC3.


b.

Turn the ignition switch to ON and turn the GTS on.


c.

Clear the DTCs.


d.

Turn the ignition switch off and wait for at least 30 seconds.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Read the DTCs.


Result:
Result Proceed to
DTC P061512 is output A
DTCs are not output B



A

5.CHECK ENTRY AND START SYSTEM (START FUNCTION)

B

END

5.CHECK ENTRY AND START SYSTEM (START FUNCTION)

Result:
Proceed to
OK
NG



OK

NG

REPAIR ENTRY AND START SYSTEM

6.INSPECT CLUTCH START SWITCH
a.

Inspect the clutch start switch.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

REPLACE CLUTCH START SWITCH

7.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (clutch start switch assembly - ST relay - ECM - certification ECU (smart key ECU assembly)).


Result:
Proceed to
NEXT



NEXT

4.CHECK WHETHER DTC OUTPUT RECURS (DTC P061512)
8.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
a.

Result:
Proceed to
OK
NG



OK

9.INSPECT IGNITION SWITCH ASSEMBLY

NG

9.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

10.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

11.REPLACE IGNITION SWITCH ASSEMBLY
10.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (park/neutral position switch assembly - ST relay - ECM).


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER DTC OUTPUT RECURS
11.REPLACE IGNITION SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

12.CONFIRM WHETHER DTC OUTPUT RECURS
12.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off and wait for 30 seconds.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

13.INSPECT CLUTCH START SWITCH ASSEMBLY
a.

Inspect the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

14.INSPECT IGNITION SWITCH ASSEMBLY

NG

18.REPLACE CLUTCH START SWITCH ASSEMBLY
14.INSPECT IGNITION SWITCH ASSEMBLY
a.

Inspect the ignition switch assembly.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>IGNITION SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

15.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)

NG

16.REPLACE IGNITION SWITCH ASSEMBLY
15.REPAIR OR REPLACE HARNESS OR CONNECTOR (STA SIGNAL CIRCUIT)
a.

Repair or replace the harness or connector (clutch start switch assembly - ST relay - ECM).


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER DTC OUTPUT RECURS
16.REPLACE IGNITION SWITCH ASSEMBLY
a.

Replace the ignition switch assembly.

Click hereEngine / Hybrid System>1GD-FTV (STARTING)>IGNITION SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER DTC OUTPUT RECURS
17.CONFIRM WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs.


c.

Turn the ignition switch off and wait for 30 seconds.


d.

Turn the ignition switch to ON and turn the GTS on.


e.

Drive the vehicle for 25 seconds or more at a speed of 20 km/h (12.4 mph) or more and an engine speed of 1000 rpm or more.


f.

Enter the following menus: Powertrain / Engine / Trouble Codes.


g.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END

18.REPLACE CLUTCH START SWITCH ASSEMBLY
a.

Replace the clutch start switch assembly.

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>REMOVAL


Result:
Proceed to
NEXT



NEXT

17.CONFIRM WHETHER DTC OUTPUT RECURS