For more information on the air fuel ratio sensor and Diesel Particulate Filter (DPF), refer to the following procedures.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION
This DTC is related to the air fuel ratio sensor, although the caption is the oxygen sensor.
The air fuel ratio sensor outputs a voltage* that is proportional to the air fuel ratio. The air fuel ratio sensor output voltage is used to control the air fuel ratio mixture.
The air fuel ratio sensor is located after the Diesel Particulate Filter (DPF) catalytic converter. This sensor has been developed based on the structure and technology of the air fuel ratio sensor that is used for gasoline engine. The cover for the sensor electrode has been modified to suit its application in a diesel engine. This change allows the sensor to function effectively in this DPF type diesel engine, and it also avoids problems with sensor temperature and Particulate Matter (PM).
In order to reduce PM, the ECM adjusts the air fuel ratio to a value slightly richer than that which would otherwise be used (note that this mixture is still leaner than the stoichiometric air fuel ratio). The ECM controls these adjustments on signals from the air fuel ratio sensor.
When the ECM performs PM forced regeneration (cleaning) by adding fuel using the exhaust fuel addition injector assembly, the air fuel ratio sensor feedback is used to ensure that an appropriate air fuel ratio is maintained.
*: This voltage change occurs only inside the ECM. It is not possible to measure this voltage at the sensor. The GTS can be used to monitor this voltage.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | Note |
|---|---|---|---|---|---|---|
| P003012 | HO2S Heater Control Bank 1 Sensor 1 Circuit Short to Battery | Air fuel ratio sensor heater current is 11.5 A or higher when the heater does not operate for 10 seconds (1 trip detection logic). | ·
Short in air fuel ratio sensor heater circuit ·
Air fuel ratio sensor heater ·
ECM |
Comes on | DTC stored | SAE Code: P0032 |
| P003013 | HO2S Heater Control Bank 1 Sensor 1 Circuit Open | Air fuel ratio sensor heater current is 0.8 A or less when the heater operates for 10 seconds (1 trip detection logic). | ·
Open in air fuel ratio sensor heater circuit ·
Air fuel ratio sensor heater ·
ECM |
Comes on | DTC stored | SAE Code: P0031 |
| P101A9E | A/F Sensor Heater Performance Bank 1 Sensor 1 Stuck On | The air fuel ratio sensor heater voltage level is low while the heater is not operating (1 trip detection logic). | ·
Short in air fuel ratio sensor heater circuit ·
Air fuel ratio sensor heater ·
ECM |
Comes on | DTC stored | SAE Code: P101D |
| DTC No. | Data List |
|---|---|
| P003012
P003013 P101A9E |
·
A/F (O2) Lambda B1S1 ·
Exhaust Temperature B1S2 |
The inner surface of the air fuel ratio sensor element is exposed to outside air. The outer surface of the sensor element is exposed to exhaust gases. The sensor element is made of platinum coated zirconia and includes an integrated heating element. The zirconia element generates a small voltage when there is a large difference in the oxygen concentrations of the exhaust and the outside air. The platinum coating amplifies the voltage generation. When heated, the sensor becomes very efficient. If the temperature of the exhaust is low without supplemental heating, the sensor will not generate useful voltage signals. The ECM controls the heating by using a duty-cycle to regulate the average current in the heater element. If the heater current is out of the normal range, the output signals of the sensor are inaccurate and the ECM cannot regulate the air fuel ratio properly. When the heater current is out of the normal operating range, the ECM interprets this as a malfunction and stores a DTC.
| DTC No. | DTC Detection Drive Pattern |
|---|---|
| P003012
P101A9E |
Engine switch on (IG) for 10 seconds |
| P003013 | ·
Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more. ·
Check that "Exhaust Temperature B1S2" displays 200°C (392°F) or higher using the GTS. |
Inspect the fuses of circuits related to this system before performing the following procedure.
After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).
Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
Inspect the air fuel ratio sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Front view of wire harness connector
(to Air Fuel Ratio Sensor) |
Disconnect the air fuel ratio sensor connector.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| C131-2 (+B) - Body ground | Engine switch on (IG) | 11 to 14 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the air fuel ratio sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C131-1 (HA1A) - C150-5 (HA1A) | Always | Below 1 Ω |
| C131-1 (HA1A) or C150-5 (HA1A) - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Replace the ECM.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECM>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the air fuel ratio sensor connector.
Remove the No. 1 integration relay.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| C131-2 (+B) - 1W-3 | Always | Below 1 Ω |
| 1W-2 - 1W-4 | Always | Below 1 Ω |
| 1W-4 - Body ground | Always | Below 1 Ω |
| C131-2 (+B) or 1W-3 - Body ground and other terminals | Always | 10 kΩ or higher |
| 1W-2 or 1W-4 - Body ground and other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Inspect the No. 1 integration relay (EFI MAIN NO. 2 relay).
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>RELAY (w/o Urea SCR System)>ON-VEHICLE INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the ECM power source circuit.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>ECM Power Source Circuit
| Proceed to |
|---|
| NEXT |
NEXT
Replace the air fuel ratio sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL
Perform "A/F Sensor Learning Value Clear" after replacing the air fuel ratio sensor.
Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION
| Proceed to |
|---|
| NEXT |
NEXT
Repair or replace harness or connector.
| Proceed to |
|---|
| NEXT |
NEXT
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear the DTCs.
Turn the engine switch off for 30 seconds or more.
Turn the engine switch on (IG).
Turn the GTS on.
Drive the vehicle at 50 km/h (30 mph) or higher for a total of 300 seconds or more.
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
"Exhaust Temperature B1S2" on the GTS screen should be 200°C (392°F) or higher.
Confirm that the DTC is not output.
Perform the following procedure using the GTS to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P003012, P003013 or P101A9E.
Check that STATUS is NORMAL.
If STATUS is NORMAL, DTC judgment is complete and the system is determined to be normal.
If STATUS is INCOMPLETE, DTC judgment is incomplete. Drive the vehicle at 50 km/h (30 mph) or higher for a total of 300 seconds or more again.
| Proceed to |
|---|
| NEXT |
NEXT