Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P200C4B  Particulate Filter Over Temperature Bank 1 Over Temperature  P200E4B  Catalyst System Over Temperature Bank 1 Over Temperature  P24284B  Exhaust Gas Temperature Too High Bank 1 Over Temperature  


DESCRIPTION

A351107C02
2.031,2.771 2.135,2.771 2.135,2.771 2.385,2.5 true 0.271,0.677 0.583,0.875 0.313,0.198 10 false *a 0.833,0.448 1.146,0.646 0.313,0.198 10 false *1 2.854,1.469 3.094,1.688 0.24,0.219 10 false *5 3.042,2.052 3.354,2.25 0.313,0.198 10 false *6 2.885,2.823 3.198,3.021 0.313,0.198 10 false *7 2.854,3.323 3.167,3.521 0.313,0.198 10 false *4 6.229,1.958 6.542,2.156 0.313,0.198 10 false *8 1.531,1.76 1.771,1.979 0.24,0.219 10 false *2 1.844,2.719 2.156,2.917 0.313,0.198 10 false *3
*1 Exhaust Fuel Addition Injector Assembly *2 Turbocharger Sub-assembly
*3 DPF Catalytic Converter *4 Air Fuel Ratio Sensor
*5 Exhaust Gas Temperature Sensor *6 No. 2 Exhaust Gas Temperature Sensor
*7 No. 3 Exhaust Gas Temperature Sensor *8 ECM
*a Exhaust Gas - -


The exhaust fuel addition injector assembly is mounted on the exhaust manifold, and low pressure fuel is supplied to the exhaust fuel addition injector assembly by the feed pump in the supply pump assembly. The exhaust fuel addition injector assembly adds fuel in response to a control signal from the ECM, in order to perform PM forced regeneration.

During PM forced regeneration, the exhaust fuel addition injector assembly adds fuel to raise the DPF* catalyst temperature.

This injector adds fuel by a control signal from the ECM.

This injector is used for two different controls: PM forced regeneration and PM reduction.

During PM forced regeneration, the injector adds fuel to raise the catalyst temperature.

In the other control, the injector helps the air-fuel ratio become rich. As a result, PM in the exhaust gas will be reduced in response to the rich air-fuel ratio.

*: Diesel Particulate Filter

HINT:
·

For more information on the exhaust fuel addition injector assembly and DPF catalyst, refer to the following procedures.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION

·

If DTC P200C4B, P200E4B and P24284B are present, refer to the diagnostic trouble code (DTC) chart for Diesel Particulate Filter System.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION



DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P200C4B Particulate Filter Over Temperature Bank 1 Over Temperature The value of "Exhaust Temperature B1S3" is higher than 1000°C (1832°F) for 5 seconds.
(1 trip detection logic)
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Exhaust manifold converter sub-assembly


Sub Trouble Area
·

No. 3 exhaust gas temperature sensor

·

Air fuel ratio sensor

·

Mass air flow meter sub-assembly

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Injector assembly

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored SAE Code: P200C
P200E4B Catalyst System Over Temperature Bank 1 Over Temperature The value of "Exhaust Temperature B1S2" is higher than 1000°C (1832°F) for 5 seconds.
(1 trip detection logic)
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Exhaust manifold converter sub-assembly


Sub Trouble Area
·

No. 2 exhaust gas temperature sensor

·

Air fuel ratio sensor

·

Mass air flow meter sub-assembly

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Injector assembly

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored SAE Code: P200E
P24284B Exhaust Gas Temperature Too High Bank 1 Over Temperature The value of "Exhaust Temperature B1S1" is higher than 1000°C (1832°F) for 5 seconds.
(1 trip detection logic)
Main Trouble Area
·

Open or short in exhaust fuel addition injector assembly

·

Exhaust fuel addition injector assembly

·

Exhaust manifold converter sub-assembly


Sub Trouble Area
·

Exhaust gas temperature sensor

·

Air fuel ratio sensor

·

Mass air flow meter sub-assembly

·

Manifold absolute pressure sensor

·

Fuel leaks or blockages in exhaust fuel addition injector assembly

·

Fuel supply pump assembly

·

Injector assembly

·

Blockages or leaks in air intake system

·

Blockages or leaks in exhaust system

·

Blockages or leaks in EGR system

·

ECM


Common Inspection Item:
·

Fuel injection system

·

Intake/Exhaust system

·

After treatment control system


Comes on DTC stored SAE Code: P2428

HINT:
·

Due to fail-safe operation when other DTCs (that involve the engine power limit) are stored, PM forced regeneration may be prohibited.

This DTC or P042000, P20CF00, P244B00 and P246300 may be stored due to the fact that PM forced regeneration is prohibited due to the fail-safe operation of other DTCs.

·

The air fuel ratio and the exhaust gas temperature can be checked by entering the following menus on the GTS: Powertrain / Engine / Data List / Diesel Exhaust / A/F (O2) Lambda B1S1, Exhaust Temperature B1S1, Exhaust Temperature B1S2 and Exhaust Temperature B1S3.

·

Malfunctions in the engine itself may affect the DPF system control and cause storage of this DTC. For example, malfunctions in the injector assemblies that cause a large amount of smoke emission: These affect the exhaust fuel addition injector assembly operation. Blockages or leaks in the air intake system, or an EGR system malfunction such as EGR passage blockages: These malfunctions affect the DPF catalyst temperature control. Therefore, the engine condition itself should also be checked, in addition to the exhaust fuel addition injector assembly.



Related Data List
DTC No. Data List
P200C4B
P200E4B
P24284B
·

Mass Air Flow Sensor

·

Intake Manifold Absolute Pressure

·

Intake Air Temperature B1S1 (Turbo)

·

Target Boost Pressure

·

Atmospheric Pressure

·

Coolant Temperature

·

Engine Speed

·

A/F (O2) Lambda B1S1

·

Exhaust Fuel Addition F/B Bank 1

·

Exhaust Temperature B1S1

·

Exhaust Temperature B1S2

·

Exhaust Temperature B1S3

·

Catalyst Differential Pressure Bank 1

·

Injection Feedback Value #1 to #4

·

Target Injection Volume



MONITOR DESCRIPTION

The ECM monitors DPF catalyst temperature. When the temperature becomes high due to uncombusted fuel, engine oil or thermal degradation to the DPF catalyst, the ECM illuminates the MIL.

A244058E17
3.927,1.177 3.406,0.469 3.406,0.469 3.135,0.469 false 0.104,0.083 1.542,0.417 1.438,0.333 10 false Malfunction Detection: 0.156,1.76 1.542,2.417 1.385,0.656 10 false Exhaust Temperature B1S1, B1S2 or B1S3 3.906,0.656 4.76,0.99 0.854,0.333 10 false MIL Goes On 5.833,1.073 7.104,1.969 1.271,0.896 10 false P200C4B, P200E4B and P24284B Threshold 2.49,0.385 3.115,0.719 0.625,0.333 10 false Abnormal 3.188,2 5.656,2.188 2.469,0.188 10 false Normal (500 to 700°C (932 to 1292°F)) 5.646,1.844 6.125,2.177 0.479,0.333 10 false Normal

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P200C4B PM forced regeneration*
*: When P200C4B is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.
P200E4B PM forced regeneration*
*: When P200E4B is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.
P24284B PM forced regeneration*
*: When P24284B is detected due to a DPF catalyst problem such as thermal degradation, because the malfunction cannot be duplicated even if the vehicle is driven after PM forced regeneration is performed, perform troubleshooting by following the diagnosis procedure and checking the freeze frame data.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click here Engine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT (RECORD STORED DTC AND FREEZE FRAME DATA) (PROCEDURE 1)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Enter the following menus: Powertrain / Engine / Trouble Codes.


d.

Record the stored DTC and freeze frame data.


Result:
Proceed to
NEXT



NEXT

2.REPLACE EXHAUST GAS TEMPERATURE SENSOR
2.REPLACE EXHAUST GAS TEMPERATURE SENSOR
a.

Check the values of "Exhaust Temperature B1S1", "Exhaust Temperature B1S2" and "Exhaust Temperature B1S3" that were saved in Procedure 1.

Result
Result Items to be Replaced
DTC P24284B is output and the value of "Exhaust Temperature B1S1" is 850°C (1562°F) or higher Exhaust gas temperature sensor
DTC P200E4B is output and the value of "Exhaust Temperature B1S2" is 850°C (1562°F) or higher No. 2 exhaust gas temperature sensor
DTC P200C4B is output and the value of "Exhaust Temperature B1S3" is 850°C (1562°F) or higher No. 3 exhaust gas temperature sensor


b.

If DTC P200C4B, P200E4B and/or P24284B is output, the exhaust gas temperature sensors need to be replaced. However, make sure to perform all diagnostic procedures for DTC P200C4B, P200E4B and/or P24284B before replacing the exhaust gas temperature sensors.

HINT:

If the exhaust gas temperature sensors are subjected to an abnormally high temperature, the internal resistance of the sensor increases. This causes incorrect temperature measurement.



Result:
Proceed to
NEXT



NEXT

3.CHECK FOR BLACK SMOKE
3.CHECK FOR BLACK SMOKE
a.

Start the engine and drive the vehicle until the engine coolant temperature reaches 75°C (167°F) or higher.


b.

Stop the vehicle and allow the engine to idle.


c.

Fully depress the accelerator pedal for 5 seconds, and then release it [A].


d.

Repeat the procedure [A] 10 times [B].


e.

Check for black smoke emission during the procedure [A] and [B].

OK:

Black smoke is emitted less than 5 times.


HINT:

Even if the black smoke is very thin, count the number of black smoke emissions if there is any visible smoke.



Result:
Proceed to
OK
NG



OK

5.CHECK FUEL INJECTION SYSTEM

NG

4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
4.REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Even though it has been determined that the exhaust manifold converter sub-assembly (DPF catalyst) needs to be replaced, make sure to perform all diagnostic procedures for DTC P200C4B, P200E4B and/or P24284B before replacing it.

HINT:

This DTC is stored because an excessive amount of PM has accumulated and resulted in abnormal combustion. It is necessary to diagnose the cause of abnormal PM accumulation and repair the problem. Therefore, do not perform replacement at this time.



Result:
Proceed to
NEXT



NEXT

5.CHECK FUEL INJECTION SYSTEM
5.CHECK FUEL INJECTION SYSTEM

Result:
Proceed to
NEXT



NEXT

6.CHECK INTAKE / EXHAUST SYSTEM
6.CHECK INTAKE / EXHAUST SYSTEM

Result:
Proceed to
NEXT



NEXT

7.CHECK AFTER TREATMENT CONTROL SYSTEM
7.CHECK AFTER TREATMENT CONTROL SYSTEM

Result:
Proceed to
NEXT



NEXT

8.REPLACE MALFUNCTIONING PARTS
8.REPLACE MALFUNCTIONING PARTS
HINT:

Replace the following items only when it has been determined necessary based on diagnosis for DTC P200C4B, P200E4B and/or P24284B.


a.

Replace the exhaust manifold converter sub-assembly.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>MONOLITHIC CONVERTER (w/ DPF)>REMOVAL

NOTICE:

Perform the initialization procedure for "Catalyst Deterioration Learning Value Clear" and "DPF Deposition Value Clear".

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION






Result:
Proceed to
NEXT



NEXT

9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
9.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG) and turn the GTS on.


c.

Clear the DTCs.


d.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


e.

Perform PM forced regeneration.

Click hereEngine / Hybrid System>1GD-FTV (EMISSION CONTROL)>EMISSION CONTROL SYSTEM>ON-VEHICLE INSPECTION

Result:

PM forced regeneration completes normally.



Result:
Proceed to
NEXT



NEXT

END