1.DRAIN ENGINE COOLANT
2.DRAIN ENGINE COOLANT (w/ Urea SCR System)
17940D
3.REMOVE INTERCOOLER ASSEMBLY (w/ Urea SCR System)
17410
4.REMOVE FRONT EXHAUST PIPE ASSEMBLY
17168
5.REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR
53736B
6.REMOVE NO. 1 FRONT FENDER APRON TO FRAME SEAL RH
17705
7.REMOVE AIR CLEANER CAP SUB-ASSEMBLY WITH AIR CLEANER HOSE
17801
8.REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY
9.REMOVE AIR CLEANER CASE SUB-ASSEMBLY
89481B
10.REMOVE DIFFERENTIAL PRESSURE SENSOR
89425
11.REMOVE EXHAUST GAS TEMPERATURE SENSOR
12633
12.REMOVE NO. 3 ENGINE COVER BRACKET (w/o Urea SCR System)
25733A
13.REMOVE NO. 1 VACUUM PIPE
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Remove the nut and clamp from the No. 1 vacuum pipe and No. 2 vacuum pipe.
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Using a 17 mm union nut wrench, remove the No. 1 vacuum pipe from the exhaust manifold converter sub-assembly.
25734
14.REMOVE NO. 2 VACUUM PIPE
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Using a 17 mm union nut wrench, remove the No. 2 vacuum pipe from the exhaust manifold converter sub-assembly.
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Remove the clamp from the pipe clamp.
17578B
15.REMOVE PIPE CLAMP
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Remove the 3 bolts and pipe clamp from the engine cover bracket.
12631A
16.REMOVE ENGINE COVER BRACKET
w/o Urea SCR System:
Detach the 2 clamp and disconnect the engine wire from the engine cover bracket.
w/ Urea SCR System:
Detach the clamp and disconnect the engine wire from the cylinder head cover sub-assembly.
w/ Urea SCR System:
Remove the bolt and disconnect the engine wire from the engine cover bracket.
| *A | w/o Urea SCR System |
| *B | w/ Urea SCR System |
Remove the 2 bolts and engine cover bracket from the cylinder head sub-assembly.
45220
17.DISCONNECT STEERING INTERMEDIATE SHAFT ASSEMBLY (for RHD)
89467B
18.REMOVE AIR FUEL RATIO SENSOR (w/o Urea SCR System)
17167
19.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
Remove the 3 bolts and No. 1 exhaust manifold heat insulator from the exhaust manifold.
17271
20.REMOVE NO. 1 TURBO INSULATOR
Remove the 3 bolts and No. 1 turbo insulator from the exhaust manifold and turbocharger subassembly.
89463C
21.DISCONNECT NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)
Disconnect the connector form the No. 1 nitrogen oxides sensor.
Remove the 2 bolt.
Detach the 4 clamps and disconnect the No. 1 nitrogen oxides sensor.
Remove the bolt and exhaust sensor clamp bracket from the cylinder head sub-assembly.
17118
22.REMOVE NO. 2 EXHAUST PIPE SUPPORT STAY
Remove the bolt, 2 nuts and No. 2 exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.
17118
23.REMOVE EXHAUST PIPE SUPPORT STAY
Remove the 3 bolts and exhaust pipe support stay from the cylinder block sub-assembly and exhaust manifold converter sub-assembly.
25051
24.REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
Remove the bolt and disconnect the No. 3 skid control clamp from the body.
w/ Rear Air Conditioning System:
Remove the bolt.
w/ Rear Air Conditioning System:
Slide the 4 clamps and remove the heater hose from the heater water pipe.
Remove the nut, exhaust pipe clamp and exhaust manifold converter sub-assembly from the turbocharger sub-assembly.
Remove the gasket.
89463C
25.REMOVE NO. 1 NITROGEN OXIDES SENSOR (w/ Urea SCR System)