Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) C

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  P223711  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground  P223712  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery  P223713  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open  P223716  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold  P223717  A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold  P225111  O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground  P225112  O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery  


DESCRIPTION

HINT:

If DTC P223711, P223712, P223713, P223716, P223717, P225111 and/or P225112 is present, refer to the DTC table for DPF system.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>SYSTEM DESCRIPTION


Refer to DTC P003012.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>P003012

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory Note
P223711 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Ground The A1A+ voltage is 1.26 V or less for 5 seconds or more (1 trip detection logic).
·

Short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored SAE Code: P2238
P223712 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Short to Battery The A1A+ voltage is higher than 4.47 V for 5 seconds or more (1 trip detection logic).
·

Open in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored SAE Code: P2239
P223713 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Open An open or ground short in the circuit between terminals A1A+ and A1A- of the air fuel ratio sensor (sensor 1) while the engine is running (1 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored SAE Code: P2237
P223716 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Below Threshold Difference between terminals A1A+ and A1A- is 0.1 V or less for 5 seconds or more (1 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored SAE Code: P2238
P223717 A/F (O2) Sensor Positive Current Control Bank 1 Sensor 1 Circuit Voltage Above Threshold Difference between terminals A1A+ and A1A- is higher than 1.0 V for 5 seconds or more (1 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored SAE Code: P2239
P225111 O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Ground The A1A- voltage is 1.07 V or less for 5 seconds or more (1 trip detection logic).
·

Short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored SAE Code: P2252
P225112 O2 Sensor Negative Current Control Bank 1 Sensor 1 Circuit Short to Battery The A1A- voltage is higher than 3.93 V for 5 seconds or more (1 trip detection logic).
·

Open or short in air fuel ratio sensor circuit

·

Air fuel ratio sensor

·

ECM


Comes on DTC stored SAE Code: P2253

Related Data List
DTC No. Data List
P223711
P223712
P223713
P223716
P223717
P225111
P225112
·

A/F (O2) Lambda B1S1

·

Exhaust Temperature B1S2



MONITOR DESCRIPTION

The air fuel ratio sensor outputs a voltage in proportion to the air fuel ratio. If impedance (alternating current resistance) or voltage output of the sensor deviates greatly from the standard range, the ECM interprets this as an open or short malfunction of the air fuel ratio sensor circuit.

CONFIRMATION DRIVING PATTERN

DTC No. DTC Detection Drive Pattern
P223713 Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.
HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S2) is 200°C (392°F) or higher.


P223711
P223712
P223716
P223717
P225111
P225112
Engine switch on (IG) for 5 seconds.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, the new ECM needs registration (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>REGISTRATION) and initialization (Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION).


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK TERMINAL VOLTAGE (AIR FUEL RATIO SENSOR VOLTAGE)
A445676C07
0.552,0.948 0.979,1.198 0.427,0.25 1.854,1.396 2.302,1.875 true 1.604,1.396 1.156,1.875 true 0.635,0.99 1.094,1.188 0.458,0.198 10 false C131 2.188,1.906 2.646,2.104 0.458,0.198 10 false A1A- 0.552,0.156 1.01,0.354 0.458,0.198 10 false *a 0.99,1.906 1.448,2.104 0.458,0.198 10 false A1A+
*a Front view of wire harness connector
(to Air Fuel Ratio Sensor)


HINT:

Make sure that the connector is properly connected. If it is not, securely connect it and check for DTCs again.


a.

Disconnect the air fuel ratio sensor connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
C131-3 (A1A+) - Body ground Engine switch on (IG) 2.8 to 3.0 V
C131-4 (A1A-) - Body ground Engine switch on (IG) 2.3 to 2.7 V
C131-3 (A1A+) - C131-4 (A1A-) Engine switch on (IG) 0.1 to 0.7 V



Result:
Proceed to
OK
NG



OK

2.REPLACE AIR FUEL RATIO SENSOR

NG

3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
2.REPLACE AIR FUEL RATIO SENSOR
a.

Replace the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>AIR FUEL RATIO SENSOR>REMOVAL

HINT:

Perform "A/F Sensor Learning Value Clear" after replacing the air fuel ratio sensor.

Click hereEngine / Hybrid System>1GD-FTV (ENGINE CONTROL)>ECD SYSTEM (w/ DPF)>INITIALIZATION



Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
3.CHECK HARNESS AND CONNECTOR (AIR FUEL RATIO SENSOR - ECM)
a.

Disconnect the air fuel ratio sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C131-3 (A1A+) - C150-33 (A1A+) Always Below 1 Ω
C131-4 (A1A-) - C150-25 (A1A-) Always Below 1 Ω
C131-3 (A1A+) - C150-33 (A1A+) - Body ground and other terminals Always 10 kΩ or higher
C131-4 (A1A-) or C150-25 (A1A-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.REPLACE ECM

NG

5.REPAIR OR REPLACE HARNESS OR CONNECTOR
4.REPLACE ECM

Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.REPAIR OR REPLACE HARNESS OR CONNECTOR
a.

Repair or replace the harness or connector.


Result:
Proceed to
NEXT



NEXT

6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
a.

Warm up the engine (engine coolant temperature is 75°C (167°F) or higher).


b.

Connect the GTS to the DLC3.


c.

Turn the engine switch on (IG).


d.

Turn the GTS on.


e.

Clear the DTCs.


f.

Turn the engine switch off and wait for 30 seconds.


g.

Start the engine and turn the GTS on.


h.

Drive the vehicle at 50 km/h (30 mph) or more for a total of 300 seconds or more.

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


HINT:

Make sure that the exhaust gas temperature (Exhaust Temperature B1S2) is 200°C (392°F) or higher.



i.

Enter the following menus: Powertrain / Engine / Trouble Codes.


j.

Confirm that the DTC is not output again.


Result:
Proceed to
NEXT



NEXT

END