Home › Engine / Hybrid System › 1GD-FTV (ENGINE CONTROL) › ECD SYSTEM (w/ DPF) › from 2020.08
RM27T0E _51 Engine / Hybrid System _053660 1GD-FTV ENGINE CONTROL _0442647 ECD SYSTEM(w/ DPF) J

1GD-FTV ENGINE CONTROL  ECD SYSTEM(w/ DPF)  Lack of Power (Turbocharger System)  


CAUTION / NOTICE / HINT

HINT:
·

The diagnosis flowchart is for lack of power due to turbocharger factors.

·

If symptom-specific diagnosis indicates a turbocharger related problem, check using this flowchart.



PROCEDURE

1.CHECK TURBOCHARGER SUB-ASSEMBLY
a.

Check that no soot or oil adheres to the turbocharger sub-assembly connectors.

A360340E03
1.552,0.583 1.708,0.781 0.156,0.198 10 false A 3.917,0.594 4.073,0.792 0.156,0.198 10 false A 3.958,3.115 4.115,3.313 0.156,0.198 10 false B 4.729,3.833 4.885,4.031 0.156,0.198 10 false B 5.385,3.146 5.542,3.344 0.156,0.198 10 false B 5.073,3.115 5.229,3.313 0.156,0.198 10 false A 4.823,2.531 4.979,2.729 0.156,0.198 10 false B 4.198,1.604 4.354,1.802 0.156,0.198 10 true A

HINT:

If adhering soot or an oil leak exists, air leaking at that position may be the cause of the lack of boost pressure.



Result:
Result Proceed to
No adhering soot or an oil A
Soot adhering around the turbine housing, flange, or V band (A in the illustration) B
Oil leak from the contact surface between the compressor housing and bearing housing (B in the illustration) C


A

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (TURBINE SHAFT)

B

5.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

2.INSPECT TURBOCHARGER SUB-ASSEMBLY (TURBINE SHAFT)
a.

Remove the turbocharger sub-assembly.

·

Check that the turbine shaft rotates smoothly, without catching.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>INSPECTION

·

Check for loose turbine mounting nuts and for axial play in the turbine shaft.

Click hereEngine / Hybrid System>1GD-FTV (INTAKE / EXHAUST)>EXHAUST MANIFOLD W/ TURBOCHARGER>INSPECTION

HINT:

If the turbine shaft catches or if there is no play or excessive play, it could indicate improper sealing due to seizing or poor sliding because of a deposit build-up.




Result:
Result Proceed to
No turbine shaft malfunction A
Turbine shaft malfunction B


A

3.INSPECT TURBOCHARGER SUB-ASSEMBLY

B

3.INSPECT TURBOCHARGER SUB-ASSEMBLY
a.

Check for interference between the turbine wheel and the turbine housing.

HINT:

When there is interference between the turbine wheel and turbine housing and the turbine wheel is damaged, check for fragments of the turbine wheel in the exhaust manifold converter subassembly.



Result:
Result Proceed to
No damage or interference A
Damage or interference exists B


A

4.INSPECT TURBOCHARGER NOZZLE VANE PLATE

B

4.INSPECT TURBOCHARGER NOZZLE VANE PLATE
a.
A348999

Inspect the turbocharger nozzle vane plate.

i.

Remove the e-washer from the turbocharger nozzle vane control actuator.



b.

Move the turbocharger vane control rod subassembly and check that the turbocharger nozzle vane plate moves.


Result:
Result Proceed to
Catches, but operates* A
Gets stuck and does not operate B

HINT:

*: Check several times.



OK

NG

5.CHECK EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY
a.

Check for deformation or cracks in the mounting surfaces on the exhaust manifold converter subassembly and the turbocharger sub-assembly.

HINT:

Deformation or cracks on a mounting surface may allow exhaust gas to leak from the damaged position.


Standard:

No deformation or cracks on a mounting surface



Result:
Result Proceed to
No problem with the mounting surface A
Deformation or cracks on the exhaust manifold converter sub-assembly mounting surface B
Deformation or cracks on the turbocharger subassembly mounting surface C


A

6.REPLACE EXHAUST PIPE CLAMP AND GASKET

B

REPLACE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

C

6.REPLACE EXHAUST PIPE CLAMP AND GASKET
a.

Replace the exhaust pipe clamp and the gasket.



NEXT

7.PERFORM SIMULATION TEST
7.PERFORM SIMULATION TEST
a.

Check that the abnormal state has disappeared.



NEXT

END